Additive Manufacturing of Semiconductor Silicon on Silicon Using Direct Laser Melting

2017 ◽  
pp. 104-116 ◽  
Author(s):  
Marie Le Dantec ◽  
Mustafa Abdulstaar ◽  
Matthias Leistner ◽  
Marc Leparoux ◽  
Patrik Hoffmann
Keyword(s):  
Additive Manufacturing ◽  
Laser Melting ◽  
Semiconductor Silicon ◽  
Direct Laser

scholarly journals Epitaxial Growth of Silicon on Silicon Wafers by Direct Laser Melting

Materials ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 4728
Author(s):  
Marie Le Dantec ◽  
Mustafa Abdulstaar ◽  
Marc Leparoux ◽  
Patrik Hoffmann
Keyword(s):  
Additive Manufacturing ◽  
Epitaxial Growth ◽  
Silicon Powder ◽  
Process Conditions ◽  
Single Element ◽  
Thermal Gradients ◽  
Laser Melting ◽  
Direct Laser ◽  
Final Microstructure ◽  
High Purity Silicon

Additive manufacturing (AM) of brittle materials remains challenging, as they are prone to cracking due to the steep thermal gradients present during melting and cooling after laser exposition. Silicon is an ideal brittle material for study since most of the physical properties of single-element materials can be found in the literature and high-purity silicon powders are readily available. Direct laser melting (DLM) of silicon powder was performed to establish the conditions under which cracks occur and to understand how the solidification front impacts the final microstructure. Through careful control of process conditions, paying special attention to thermal gradients and the growth velocity, epitaxial pillars free of cracks could be grown to a length of several millimeters.

scholarly journals Improving surface quality in selective laser melting based tool making

2021 ◽  
Author(s):  
Filippo Simoni ◽  
Andrea Huxol ◽  
Franz-Josef Villmer
Keyword(s):  
Surface Roughness ◽  
Additive Manufacturing ◽  
Surface Quality ◽  
Selective Laser Melting ◽  
Melting Process ◽  
Laser Remelting ◽  
Laser Melting ◽  
Great Cost ◽  
Starting Point ◽  
Processing Techniques

AbstractIn the last years, Additive Manufacturing, thanks to its capability of continuous improvements in performance and cost-efficiency, was able to partly replace and redefine well-established manufacturing processes. This research is based on the idea to achieve great cost and operational benefits especially in the field of tool making for injection molding by combining traditional and additive manufacturing in one process chain. Special attention is given to the surface quality in terms of surface roughness and its optimization directly in the Selective Laser Melting process. This article presents the possibility for a remelting process of the SLM parts as a way to optimize the surfaces of the produced parts. The influence of laser remelting on the surface roughness of the parts is analyzed while varying machine parameters like laser power and scan settings. Laser remelting with optimized parameter settings considerably improves the surface quality of SLM parts and is a great starting point for further post-processing techniques, which require a low initial value of surface roughness.

scholarly journals Directionally-Dependent Mechanical Properties of Ti6Al4V Manufactured by Electron Beam Melting (EBM) and Selective Laser Melting (SLM)

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3603
Author(s):  
Tim Pasang ◽  
Benny Tavlovich ◽  
Omry Yannay ◽  
Ben Jakson ◽  
Mike Fry ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Surface Roughness ◽  
Tensile Strength ◽  
Electron Beam ◽  
Additive Manufacturing ◽  
Selective Laser Melting ◽  
Electron Beam Melting ◽  
Rolling Direction ◽  
Laser Melting ◽  
Plate Rolling

An investigation of mechanical properties of Ti6Al4V produced by additive manufacturing (AM) in the as-printed condition have been conducted and compared with wrought alloys. The AM samples were built by Selective Laser Melting (SLM) and Electron Beam Melting (EBM) in 0°, 45° and 90°—relative to horizontal direction. Similarly, the wrought samples were also cut and tested in the same directions relative to the plate rolling direction. The microstructures of the samples were significantly different on all samples. α′ martensite was observed on the SLM, acicular α on EBM and combination of both on the wrought alloy. EBM samples had higher surface roughness (Ra) compared with both SLM and wrought alloy. SLM samples were comparatively harder than wrought alloy and EBM. Tensile strength of the wrought alloy was higher in all directions except for 45°, where SLM samples showed higher strength than both EBM and wrought alloy on that direction. The ductility of the wrought alloy was consistently higher than both SLM and EBM indicated by clear necking feature on the wrought alloy samples. Dimples were observed on all fracture surfaces.

Additive Manufacturing of Glass

2014 ◽  
Vol 136 (6) ◽  
Author(s):  
Junjie Luo ◽  
Heng Pan ◽  
Edward C. Kinzel
Keyword(s):  
Additive Manufacturing ◽  
Glass Powder ◽  
Processing Parameters ◽  
Gradient Index ◽  
Continuous Line ◽  
Single Track ◽  
Laser Melting ◽  
Powder Bed ◽  
Transparent Parts ◽  
Insight Into

Selective laser melting (SLM) is a technique for the additive manufacturing (AM) of metals, plastics, and even ceramics. This paper explores using SLM for depositing glass structures. A CO2 laser is used to locally melt portions of a powder bed to study the effects of process parameters on stationary particle formation as well as continuous line quality. Numerical modeling is also applied to gain insight into the physical process. The experimental and numerical results indicate that the absorptivity of the glass powder is nearly constant with respect to the processing parameters. These results are used to deposit layered single-track wide walls to demonstrate the potential of using the SLM process for building transparent parts. Finally, the powder bed process is compared to a wire-fed approach. AM of glass is relevant for gradient index optics, systems with embedded optics, and the formation of hermetic seals.

scholarly journals Additive Manufacturing of Bulk Nanocrystalline FeNdB Based Permanent Magnets

Micromachines ◽  
2021 ◽  
Vol 12 (5) ◽  
pp. 538
Author(s):  
Dagmar Goll ◽  
Felix Trauter ◽  
Timo Bernthaler ◽  
Jochen Schanz ◽  
Harald Riegel ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Melt Spinning ◽  
Permanent Magnets ◽  
Maximum Energy ◽  
Laser Melting ◽  
Powder Bed ◽  
Melt Pool ◽  
Bulk Nanocrystalline ◽  
Ribbon Structures ◽  
Nanocrystalline Ribbon

Lab scale additive manufacturing of Fe-Nd-B based powders was performed to realize bulk nanocrystalline Fe-Nd-B based permanent magnets. For fabrication a special inert gas process chamber for laser powder bed fusion was used. Inspired by the nanocrystalline ribbon structures, well-known from melt-spinning, the concept was successfully transferred to the additive manufactured parts. For example, for Nd16.5-Pr1.5-Zr2.6-Ti2.5-Co2.2-Fe65.9-B8.8 (excess rare earth (RE) = Nd, Pr; the amount of additives was chosen following Magnequench (MQ) powder composition) a maximum coercivity of µ0Hc = 1.16 T, remanence Jr = 0.58 T and maximum energy density of (BH)max = 62.3 kJ/m3 have been achieved. The most important prerequisite to develop nanocrystalline printed parts with good magnetic properties is to enable rapid solidification during selective laser melting. This is made possible by a shallow melt pool during laser melting. Melt pool depths as low as 20 to 40 µm have been achieved. The printed bulk nanocrystalline Fe-Nd-B based permanent magnets have the potential to realize magnets known so far as polymer bonded magnets without polymer.

scholarly journals Selective Laser Melting of Crack-Free High Density M2 High Speed Steel Parts by Baseplate Preheating

2014 ◽  
Vol 136 (6) ◽  
Author(s):  
Karolien Kempen ◽  
Bey Vrancken ◽  
Sam Buls ◽  
Lore Thijs ◽  
Jan Van Humbeeck ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Selective Laser Melting ◽  
High Speed ◽  
Crack Formation ◽  
High Speed Steel ◽  
Thermal Gradients ◽  
Laser Melting ◽  
Mechanical And Physical Properties ◽  
The World ◽  
M2 High Speed Steel

Cracks and delamination, resulting from residual stresses, are a barrier in the world of additive manufacturing and selective laser melting (SLM) that prohibits the use of many metals in this field. By preheating the baseplate, thermal gradients are lowered and stresses can be reduced. In this work, some initial tests were performed with M2 high speed steel (HSS). The influence of preheating on density and mechanical and physical properties is investigated. The paper shows many promising results for the production of SLM parts in materials that are very sensitive to crack formation and delamination. When using a preheating of 200 °C, crack-free M2 HSS parts were produced with a relative density of 99.8%.

Sign in / Sign up

Export Citation Format

Share Document