Texture Development under Conditions of Imposed Strain; The Influence of Stacking Fault Energy and Degree of Order

1969 ◽  
pp. 110-119 ◽  
Author(s):  
I. L. Dillamore ◽  
N. S. Stoloff
Keyword(s):  
Stacking Fault ◽  
Stacking Fault Energy ◽  
Texture Development ◽  
Degree Of Order

scholarly journals Texture Development in Extruded Al–Cu Composites

1993 ◽  
Vol 21 (2-3) ◽  
pp. 121-137 ◽  
Author(s):  
H. Gertel ◽  
H. G. Brokmeier ◽  
H. J. Bunge
Keyword(s):  
Heat Treatment ◽  
Texture Analysis ◽  
Recrystallization Texture ◽  
Stacking Fault ◽  
Stacking Fault Energy ◽  
Texture Development ◽  
Processing Conditions ◽  
Heat Treated ◽  
Temperature Heat ◽  
Temperature Heat Treatment

Extensive neutron texture analysis of extruded Al–Cu composites was conducted in order to investigate the influence of material composition as well as various processing conditions (extrusion temperature, heat treatment) on the texture development in both phases. Texture changes in cold extruded and subsequently heat treated samples were investigated up to 400℃. Moreover, the texture of a series of cold extruded samples was compared with that of warm extruded samples. It was found that the recrystallization behaviour of the two metals differs and that the stacking fault energy has a large influence on the recrystallization texture.

Deformation Textures of Ordered and Disordered Cu3Au*

1968 ◽  
Vol 12 ◽  
pp. 372-390 ◽  
Author(s):  
E. A. Starke ◽  
J. C. Ogle ◽  
C. J. Sparks
Keyword(s):  
Deformation Twinning ◽  
Stacking Fault ◽  
Stacking Fault Energy ◽  
Disordered Materials ◽  
Rolling Schedule ◽  
Total Reduction ◽  
Deformation Textures ◽  
Degree Of Order ◽  
Stacking Fault Energies

AbstractThe development of deformation textures of both initially disordered and ordered Cu3Au has been studied and discussed in terms of the stacking fault energies and twinning probabilities. No differences in the deforir.ation textures of the ordered and disordered materials were detected at deformations up to 40% reduction. However, at reductions of approximately 42% a marked difference was observed. This difference is attributed both to the degree of order and to the stacking fault energy of the ordered sample being conducive to deformation twinning at this stage of the rolling schedule. For samples which were reordered below the racrystallization temperature at intermediate stages of deformation (every 10% in total reduction) no differences between the ordered and initially disordered samples were observed up to 90% total reduction in thickness.

On effects of non-systematic reflections on weak-beam images of partial dislocations

1991 ◽  
Vol 49 ◽  
pp. 688-689
Author(s):  
K. Z. Botros ◽  
S. S. Sheinin
Keyword(s):  
High Precision ◽  
Stacking Fault ◽  
Important Application ◽  
Stacking Fault Energy ◽  
Sharp Peak ◽  
Weak Beam ◽  
Partial Dislocations ◽  
Deviation Parameter ◽  
Beam Diffraction

The main features of weak beam images of dislocations were first described by Cockayne et al. using calculations of intensity profiles based on the kinematical and two beam dynamical theories. The feature of weak beam images which is of particular interest in this investigation is that intensity profiles exhibit a sharp peak located at a position very close to the position of the dislocation in the crystal. This property of weak beam images of dislocations has an important application in the determination of stacking fault energy of crystals. This can easily be done since the separation of the partial dislocations bounding a stacking fault ribbon can be measured with high precision, assuming of course that the weak beam relationship between the positions of the image and the dislocation is valid. In order to carry out measurements such as these in practice the specimen must be tilted to "good" weak beam diffraction conditions, which implies utilizing high values of the deviation parameter Sg.

Structural features and strength behavior of TRIP/TWIP steels

2020 ◽  
pp. 5-18
Author(s):  
D. V. Prosvirnin ◽  
◽  
M. S. Larionov ◽  
S. V. Pivovarchik ◽  
A. G. Kolmakov ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Chemical Composition ◽  
Thermomechanical Processing ◽  
Maximum Load ◽  
Structural Features ◽  
Stacking Fault ◽  
Stacking Fault Energy ◽  
Structural And Functional Properties ◽  
Twip Steels ◽  
The Creation

A review of the literature data on the structural features of TRIP / TWIP steels, their relationship with mechanical properties and the relationship of strength parameters under static and cyclic loading was carried out. It is shown that the level of mechanical properties of such steels is determined by the chemical composition and processing technology (thermal and thermomechanical processing, hot and cold pressure treatment), aimed at achieving a favorable phase composition. At the atomic level, the most important factor is stacking fault energy, the level of which will be decisive in the formation of austenite twins and / or the formation of strain martensite. By selecting the chemical composition, it is possible to set the stacking fault energy corresponding to the necessary mechanical characteristics. In the case of cyclic loads, an important role is played by the strain rate and the maximum load during testing. So at high loading rates and a load approaching the yield strength under tension, the intensity of the twinning processes and the formation of martensite increases. It is shown that one of the relevant ways to further increase of the structural and functional properties of TRIP and TWIP steels is the creation of composite materials on their basis. At present, surface modification and coating, especially by ion-vacuum methods, can be considered the most promising direction for the creation of such composites.

scholarly journals A theoretical calculation of stacking fault energy of Ni alloys: The effects of temperature and composition

2021 ◽  
Vol 191 ◽  
pp. 110326
Author(s):  
Mohammad S. Dodaran ◽  
Shengmin Guo ◽  
Michael M. Khonsari ◽  
Nima Shamsaei ◽  
Shuai Shao
Keyword(s):  
Theoretical Calculation ◽  
Stacking Fault ◽  
Stacking Fault Energy ◽  
Ni Alloys ◽  
Effects Of Temperature
Sign in / Sign up

Export Citation Format

Share Document