Experimental investigation of extinction properties and thermal conductivity of metal-coated dielectric fibers in vacuum

1987 ◽  
Vol 8 (2) ◽  
pp. 263-280 ◽  
Author(s):  
H. Reiss ◽  
F. Schmaderer ◽  
G. Wahl ◽  
B. Ziegenbein ◽  
R. Caps
Keyword(s):  
Thermal Conductivity ◽  
Experimental Investigation

Numerical Simulation & Experimental Investigation of SMT Laser Microsoldering Thermal Process

1991 ◽  
Vol 226 ◽  
Author(s):  
Wang Chunqing ◽  
Qian Yiyu ◽  
Jiang Yihong
Keyword(s):  
Thermal Conductivity ◽  
Numerical Simulation ◽  
Experimental Investigation ◽  
Thermal Process ◽  
Light Wave ◽  
Light Reflection ◽  
Lead Wire ◽  
Wire Surface ◽  
Conductivity Variation ◽  
Thermal Conductivity Variation

AbstractIn this paper,a numerical simulation of thermal process in the SMT laser microsoldering joint has been developed, in which, the influence on thermal process of the factors such as the thermal conductivity variation of solder with temperature, light reflection coefficient of the lead wire surface, and heat exchange on the surface of SMT materials all have been considered. In order to carry this numerical calculation practice and prove it's results,the reflexive characteristic of light wave to the SMT materials has been gauged,and the dynamic temperature process of laser microjoint has been measured by a new experimental method which was invented by the authors.The results of numerical simulation have been borne out by the tests, and the influences of heating parameters on thermal process has been analysed in this paper.The conclusions will be advantageous to the further study of the microjoint quality control in the SMT laser microsoldering.

Experimental Investigation on the Thermal Conductivity and Viscosity of Silver-Deionized Water Nanofluid

2010 ◽  
Vol 23 (4) ◽  
pp. 317-332 ◽  
Author(s):  
L. Godson ◽  
B. Raja ◽  
D. Mohan Lal ◽  
S. Wongwises
Keyword(s):  
Thermal Conductivity ◽  
Experimental Investigation ◽  
Deionized Water

scholarly journals Experimental investigation of rockwool insulation hygrothermal properties related to material structure

2015 ◽  
Vol 19 (3) ◽  
pp. 923-928 ◽  
Author(s):  
Maja Djurovic-Petrovic
Keyword(s):  
Thermal Conductivity ◽  
Experimental Investigation ◽  
Sorption Properties ◽  
Material Structure ◽  
Insulation Material ◽  
Wide Range ◽  
Two Samples

The hygrothermal properties related to rockwool insulation material structure with different additives are presented using rockwool insulation products obtained from row material of southern Serbia (Vranje region) in the wide range of reference temperatures (10?C to 70?C). The hygrothermal properties of basic sample (without additives) are compared to two samples with different additives for two sets of rockwool insulation samples namely: light-soft-panels (LSP) with density of 50 kg/m3, and middle-weight-panels (MWP) with density of 80 kg/m3. It is shown that there is significant (approximately 10%) improvement of thermal conductivity for additives based on zeolite. Also, correlation of thermal conductivity and sorption properties of selected samples are presented.

Experimental Investigation of Effective Thermal Conductivity for LHP Wicks

2010 ◽  
Author(s):  
Gongming Xin ◽  
Kehang Cui ◽  
Yan Chen ◽  
Wenjing Du ◽  
Yong Zou ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Experimental Investigation ◽  
Effective Thermal Conductivity ◽  
Pure Copper ◽  
Pure Nickel ◽  
Loop Heat Pipe ◽  
Porosity Level ◽  
Nickel Powders ◽  
Copper Powders ◽  
Reasonable Prediction

In this study, the effective thermal conductivity (ETC) of sintered loop heat pipe wicks, with pure nickel powders, pure copper powders, Ni-10wt%Cu powders and Ni-20wt%Cu powders were experimentally investigated. The ETC of sintered Ni-Cu wicks is found less than those of sintered pure nickel wick and sintered pure copper wicks. In the same porosity level, addition of copper into nickel will reduce ETC of the sintered Ni-Cu wicks. The sintered Ni-20wt%Cu wick presents the lowest ETC among the tested wick samples. Compared to experimental results, Alexander model can provide a reasonable prediction in some wick samples.

Experimental investigation of extinction properties and thermal conductivity of metal-coated dielectric fibers in vacuum

1985 ◽  
Author(s):  
H. REISS ◽  
F. SCHMADERER ◽  
G. WAHL ◽  
B. ZIEGENBEIN ◽  
R. CAPS
Keyword(s):  
Thermal Conductivity ◽  
Experimental Investigation

scholarly journals The Fabrication of Geopolymer Foam Composites Incorporating Coke Dust Waste

Processes ◽  
2020 ◽  
Vol 8 (9) ◽  
pp. 1052
Author(s):  
Buczkowska Katarzyna ◽  
Chi Hiep Le ◽  
Petr Louda ◽  
Szczypiński Michał ◽  
Totka Bakalova ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Experimental Investigation ◽  
Residual Strength ◽  
Elevated Temperatures ◽  
Composite Foam ◽  
Coke Dust ◽  
Composite Foams ◽  
Negative Effect ◽  
Geopolymer Binder

This paper reports the results of an experimental investigation on the mechanical properties of geopolymer foams incorporating filler from the coke dust waste (CDW). In this work, CDW was used to replace a part of geopolymer paste at 5%, 10%, 20%, and 30% by geopolymer binder mass. The physico-mechanical properties and thermal resistance against high temperatures of CDW/geopolymer foams are presented. The primary results obtained show that the use of CDW in the production of geopolymer foam composites made it possible for them to achieve relatively good mechanical properties. However, the incorporation of the CDW into the geopolymer had a slightly negative effect on thermal conductivity, but significantly improved the mechanical strength of the final product. Moreover, this waste also helped the composite foam to achieve a structure with more uniform open pores distribution, compared to the pure foam. After exposure to elevated temperatures, the residual strength of the composite foams maintained well compared to the pure foams.

Sign in / Sign up

Export Citation Format

Share Document