The molecular weight of the polyethylene oxide as a factor in the physico-mechanical properties of wet-spun triacetate fibre

1973 ◽  
Vol 5 (4) ◽  
pp. 428-431
Author(s):  
M. V. Polovnikova ◽  
I. Z. Zakirov ◽  
M. Sh. Tairov ◽  
B. E. Geller ◽  
L. G. Polyantseva
Keyword(s):  
Mechanical Properties ◽  
Molecular Weight ◽  
Polyethylene Oxide ◽  
Triacetate Fibre

Molecular Weight Effects on the Processing, Thermal, and Mechanical Properties of Oligomeric Bisphenol a Phthalonitrile Resins

2019 ◽  
Author(s):  
Tristan Butler ◽  
Stephen Deese ◽  
Madeleine Taylor ◽  
Matt Laskoski
Keyword(s):  
Mechanical Properties ◽  
Molecular Weight ◽  
Bisphenol A ◽  
Thermal And Mechanical Properties

Influence of resin molecular weight on bonding interface, water resistance, and mechanical properties of bamboo scrimber composite

2021 ◽  
Vol 292 ◽  
pp. 123458
Author(s):  
Fei Rao ◽  
Yaohui Ji ◽  
Yuxiang Huang ◽  
Neng Li ◽  
Yahui Zhang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Molecular Weight ◽  
Water Resistance ◽  
Bonding Interface ◽  
Bamboo Scrimber

scholarly journals Melt- vs. Non-Melt Blending of Complexly Processable Ultra-High Molecular Weight Polyethylene/Cellulose Nanofiber Bionanocomposite

Polymers ◽  
2021 ◽  
Vol 13 (3) ◽  
pp. 404
Author(s):  
Nur Sharmila Sharip ◽  
Hidayah Ariffin ◽  
Tengku Arisyah Tengku Yasim-Anuar ◽  
Yoshito Andou ◽  
Yuki Shirosaki ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Molecular Weight ◽  
Tensile Strength ◽  
Yield Strength ◽  
Young’S Modulus ◽  
High Molecular Weight ◽  
Melt Processing ◽  
Cellulose Nanofiber ◽  
Melt Blending ◽  
Ultra High Molecular Weight

The major hurdle in melt-processing of ultra-high molecular weight polyethylene (UHMWPE) nanocomposite lies on the high melt viscosity of the UHMWPE, which may contribute to poor dispersion and distribution of the nanofiller. In this study, UHMWPE/cellulose nanofiber (UHMWPE/CNF) bionanocomposites were prepared by two different blending methods: (i) melt blending at 150 °C in a triple screw kneading extruder, and (ii) non-melt blending by ethanol mixing at room temperature. Results showed that melt-processing of UHMWPE without CNF (MB-UHMWPE/0) exhibited an increment in yield strength and Young’s modulus by 15% and 25%, respectively, compared to the Neat-UHMWPE. Tensile strength was however reduced by almost half. Ethanol mixed sample without CNF (EM-UHMWPE/0) on the other hand showed slight decrement in all mechanical properties tested. At 0.5% CNF inclusion, the mechanical properties of melt-blended bionanocomposites (MB-UHMWPE/0.5) were improved as compared to Neat-UHMWPE. It was also found that the yield strength, elongation at break, Young’s modulus, toughness and crystallinity of MB-UHMWPE/0.5 were higher by 28%, 61%, 47%, 45% and 11%, respectively, as compared to the ethanol mixing sample (EM-UHMWPE/0.5). Despite the reduction in tensile strength of MB-UHMWPE/0.5, the value i.e., 28.4 ± 1.0 MPa surpassed the minimum requirement of standard specification for fabricated UHMWPE in surgical implant application. Overall, melt-blending processing is more suitable for the preparation of UHMWPE/CNF bionanocomposites as exhibited by their characteristics presented herein. A better mechanical interlocking between UHMWPE and CNF at high temperature mixing with kneading was evident through FE-SEM observation, explains the higher mechanical properties of MB-UHMWPE/0.5 as compared to EM-UHMWPE/0.5.

scholarly journals Improving Rheological and Mechanical Properties of Various Virgin and Recycled Polypropylenes by Blending with Long-Chain Branched Polypropylene

Polymers ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 1137
Author(s):  
Sascha Stanic ◽  
Thomas Koch ◽  
Klaus Schmid ◽  
Simone Knaus ◽  
Vasiliki-Maria Archodoulaki
Keyword(s):  
Mechanical Properties ◽  
Molecular Weight ◽  
Tensile Test ◽  
Reactive Extrusion ◽  
Original Material ◽  
Melt Flow Rate ◽  
Single Screw Extruder ◽  
Pp Blends ◽  
The Impact ◽  
Long Chain

Blends of two long-chain branched polypropylenes (LCB-PP) and five linear polypropylenes (L-PP) were prepared in a single screw extruder at 240 °C. The two LCB-PPs were self-created via reactive extrusion at 180 °C by using dimyristyl peroxydicarbonate (PODIC C126) and dilauroyl peroxide (LP) as peroxides. For blending two virgin and three recycled PPs like coffee caps, yoghurt cups and buckets with different melt flow rate (MFR) values were used. The influence of using blends was assessed by investigating the rheological (dynamic and extensional rheology) and mechanical properties (tensile test and impact tensile test). The dynamic rheology indicated that the molecular weight as well as the molecular weight distribution could be increased or broadened. Also the melt strength behavior could be improved by using the two peroxide modified LCB-PP blends on the basis of PODIC C126 or PEROXAN LP (dilauroyl peroxide). In addition, the mechanical properties were consistently enhanced or at least kept constant compared to the original material. In particular, the impact tensile strength but also the elongation at break could be increased considerably. This study showed that the blending of LCB-PP can increase the investigated properties and represents a promising option, especially when using recycled PP, which demonstrates a real “up-cycling” process.

scholarly journals The Effect of Stereocomplex Polylactide Particles on the Stereocomplexation of High Molecular Weight Polylactide Blends

Polymers ◽  
2021 ◽  
Vol 13 (12) ◽  
pp. 2018
Author(s):  
Muhammad Samsuri ◽  
Ihsan Iswaldi ◽  
Purba Purnama
Keyword(s):  
Mechanical Properties ◽  
Molecular Weight ◽  
High Molecular Weight ◽  
Nucleating Agent ◽  
Solution Casting ◽  
Casting Method ◽  
Crystalline Fraction ◽  
Crystalline Structures ◽  
Solution Casting Method

Stereocomplexation is one of several approaches for improving polylactide (PLA) properties. The high molecular weight of poly L-lactide (PLLA) and poly D-lactide (PDLA) homopolymers are a constraint during the formation of stereocomplex PLAs (s-PLAs). The presence of s-PLA particles in PLA PLLA/PDLA blends can initiate the formation of s-PLA crystalline structures. We used the solution casting method to study the utilization of s-PLA materials from high molecular weight PLLA/PDLA blends for increasing s-PLA formation. The s-PLA particles initiated the formation of high molecular weight PLLA/PDLA blends, obtaining 49.13% s-PLA and 44.34% of the total crystalline fraction. In addition, the mechanical properties were enhanced through s-PLA crystalline formation and the increasing of total crystallinity of the PLLA/PDLA blends. The s-PLA particles supported initiation for s-PLA formation and acted as a nucleating agent for PLA homopolymers. These unique characteristics of s-PLA particles show potential to overcome the molecular weight limitation for stereocomplexation of PLLA/PDLA blends.

scholarly journals Cationic Copolymerization of Isobutylene with 4-Vinylbenzenecyclobutylene: Characteristics and Mechanisms

Polymers ◽  
2020 ◽  
Vol 12 (1) ◽  
pp. 201 ◽  
Author(s):  
Zhifei Chen ◽  
Shuxin Li ◽  
Yuwei Shang ◽  
Shan Huang ◽  
Kangda Wu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Molecular Weight ◽  
Cationic Polymerization ◽  
Transfer Reaction ◽  
Chain Transfer ◽  
Solid Phase ◽  
Random Copolymer ◽  
Glass Transition Temperatures ◽  
Cationic Copolymerization ◽  
Chain Transfer Reaction

A random copolymer of isobutylene (IB) and 4-vinylbenzenecyclobutylene (4-VBCB) was synthesized by cationic polymerization at −80 °C using 2-chloro-2,4,4-trimethylpentane (TMPCl) as initiator. The laws of copolymerization were investigated by changing the feed quantities of 4-VBCB. The molecular weight of the copolymer decreased, and its molecular weight distribution (MWD) increased with increasing 4-VBCB content. We proposed a possible copolymerization mechanism behind the increase in the chain transfer reaction to 4-VBCB with increasing of feed quantities of 4-VBCB. The thermal properties of the copolymers were studied by solid-phase heating and crosslinking. After crosslinking, the decomposition and glass transition temperatures (Tg) of the copolymer increased, the network structure that formed did not break when reheated, and the mechanical properties remarkably improved.

Effect of molecular weight on mechanical properties and microstructure of 3D printed PEEK

2020 ◽  
Author(s):  
Qinfei Xu ◽  
Yingshuang Shang ◽  
Zilong Jiang ◽  
Zhaoyang Wang ◽  
Chenyi Zhou ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Molecular Weight ◽  
3D Printed

Junction Size and Mechanical Properties of Atactic and Syndiotactic High-Molecular Weight Poly(vinyl alcohol) Hydrogels

2012 ◽  
Vol 69 (11) ◽  
pp. 623-630 ◽  
Author(s):  
Risei WADA ◽  
Hidenobu SHIMIZU ◽  
Masaru OKABE
Keyword(s):  
Mechanical Properties ◽  
Molecular Weight ◽  
High Molecular Weight ◽  
Vinyl Alcohol ◽  
Poly Vinyl Alcohol ◽  
High Molecular Weight Poly

Influence of stereospecificity and molecular weight on mechanical properties of iso-syndio-polypropylene obtained by combination of metallocene catalysts

2017 ◽  
Vol 90 ◽  
pp. 183-194 ◽  
Author(s):  
Ester López-Moya ◽  
Rafael van Grieken ◽  
Alicia Carrero ◽  
Beatriz Paredes
Keyword(s):  
Mechanical Properties ◽  
Molecular Weight ◽  
Metallocene Catalysts
Sign in / Sign up

Export Citation Format

Share Document