Progressive inelastic deformation characteristics of cylindrical structure with plate-to-shell junction under moving temperature front

2003 ◽  
Vol 17 (3) ◽  
pp. 400-408 ◽  
Author(s):  
Hyeong Yeon Lee ◽  
Jong Bum Kim ◽  
Jae-Han Lee
Keyword(s):  
Inelastic Deformation ◽  
Deformation Characteristics ◽  
Cylindrical Structure ◽  
Temperature Front

Cyclic Loading Histories for Seismic Experimentation on Structural Components

1996 ◽  
Vol 12 (1) ◽  
pp. 1-12 ◽  
Author(s):  
Helmut Krawinkler
Keyword(s):  
Inelastic Deformation ◽  
Cyclic Load ◽  
Deformation Characteristics ◽  
Frequency Content ◽  
Structural Components ◽  
Seismic Demands ◽  
Critical Issues ◽  
Load Tests ◽  
Two Parameters ◽  
Selection Of

In order to utilize results obtained from quasi-static cyclic load tests on structural components for a general performance evaluation, the need exists to establish loading histories that capture critical issues of component capacity as well as seismic demands. In inelastic seismic problems capacity and demands cannot be separated since one may strongly depend on the other. Because of cumulative damage issues the capacity depends on the number of inelastic excursions and the magnitude of each excursion (not just the largest one). These two parameters depend on the frequency content of the ground motion, the period(s) of the structure, and the strength and inelastic deformation characteristics of the structure. The paper presents procedures how these characteristics can be considered in the selection of suitable loading histories.

Transmission Electron Microscopic Observations of Al3Li and Al3Ti Precipitation in A Rapidly Solidified Al-3Li-0.2Ti ALLOY

1980 ◽  
Vol 38 ◽  
pp. 336-337
Author(s):  
J. E. O’Neal ◽  
K. K. Sankaran ◽  
S. M. L. Sastry
Keyword(s):  
Rapid Solidification ◽  
Metallic Substrate ◽  
Deformation Characteristics ◽  
Phase Decomposition ◽  
Electron Microscopic ◽  
Transmission Electron ◽  
Supersaturated Solid Solutions ◽  
Transmission Electron Microscopic ◽  
Rapidly Solidified ◽  
Microstructural Homogeneity

Rapid solidification of a molten, multicomponent alloy against a metallic substrate promotes greater microstructural homogeneity and greater solid solubility of alloying elements than can be achieved by slower-cooling casting methods. The supersaturated solid solutions produced by rapid solidification can be subsequently annealed to precipitate, by controlled phase decomposition, uniform 10-100 nm precipitates or dispersoids. TEM studies were made of the precipitation of metastable Al3Li(δ’) and equilibrium AL3H phases and the deformation characteristics of a rapidly solidified Al-3Li-0.2Ti alloy.

Effect Of Elevated Temperatures On Complete Concrete Deformation Diagrams

2019 ◽  
pp. 9-14
Keyword(s):  
Experimental Data ◽  
Elastic Modulus ◽  
Elevated Temperatures ◽  
Peak Load ◽  
Relative Deformation ◽  
Deformation Characteristics ◽  
Compression Tests ◽  
Strain Behavior ◽  
Different Temperatures ◽  
Deformation Diagrams

The analysis of the previous results of the study on concrete stress-strain behavior at elevated temperatures has been carried out. Based on the analysis, the main reasons for strength retrogression and elastic modulus reduction of concrete have been identified. Despite a significant amount of research in this area, there is a large spread in experimental data received, both as a result of compression and tension. In addition, the deformation characteristics of concrete are insufficiently studied: the coefficient of transverse deformation, the limiting relative compression deformation corresponding to the peak load and the almost complete absence of studies of complete deformation diagrams at elevated temperatures. The two testing chambers provided creating the necessary temperature conditions for conducting studies under bending compression and tension have been developed. On the basis of the obtained experimental data of physical and mechanical characteristics of concrete at different temperatures under conditions of axial compression and tensile bending, conclusions about the nature of changes in strength and deformation characteristics have been drawn. Compression tests conducted following the method of concrete deformation complete curves provided obtaining diagrams not only at normal temperature, but also at elevated temperature. Based on the experimental results, dependences of changes in prism strength and elastic modulus as well as an equation for determining the relative deformation and stresses at elevated temperatures at all stages of concrete deterioration have been suggested.

Sign in / Sign up

Export Citation Format

Share Document