Highly stretchable thermal interface materials with uniformly dispersed network of exfoliated graphite nanoplatelets via ball milled processing route

2018 ◽  
Vol 24 (9) ◽  
pp. 3667-3675 ◽  
Author(s):  
Tien-Chan Chang ◽  
Chun-An Liao ◽  
Zhi-Yu Lin ◽  
Yiin-Kuen Fuh
Keyword(s):  
Exfoliated Graphite ◽  
Processing Route ◽  
Thermal Interface Materials ◽  
Graphite Nanoplatelets ◽  
Thermal Interface ◽  
Highly Stretchable ◽  
Exfoliated Graphite Nanoplatelets ◽  
Interface Materials

scholarly journals Ball-Milled Recycled Lead-Graphite Pencils as Highly Stretchable and Low-Cost Thermal-Interface Materials

Polymers ◽  
2018 ◽  
Vol 10 (7) ◽  
pp. 799 ◽  
Author(s):  
Chun-An Liao ◽  
Yee-Kwan Kwan ◽  
Tien-Chan Chang ◽  
Yiin-Kuen Fuh
Keyword(s):  
Low Cost ◽  
Exfoliated Graphite ◽  
Thermal Interface Materials ◽  
Graphite Nanoplatelets ◽  
Thermal Interface ◽  
Thermally Conductive ◽  
Highly Stretchable ◽  
Exfoliated Graphite Nanoplatelets ◽  
Interface Materials ◽  
Thermal Conductivities

A simple and sustainable production of nanoplatelet graphite at low cost is presented using carbon-based materials, including the recycled lead-graphite pencils. In this work, exfoliated graphite nanoplatelets (EGNs), ball-milled exfoliated graphite nanoplatelets (BMEGNs) and recycled lead-graphite pencils (recycled 2B), as well as thermally cured polydimethylsiloxane (PDMS), are used to fabricate highly stretchable thermal-interface materials (TIMs) with good thermally conductive and mechanically robust properties. Several characterization techniques including scanning electron microscopy (SEM) and thermogravimetric analysis (TGA) showed that recycled nanoplatelet graphite with lateral size of tens of micrometers can be reliably produced. Experimentally, the thermal conductivity was measured for EGNs, BMEGNs and recycled 2B fillers with/without the effect of ball milling. The in-plane thermal conductivities of 12.97 W/mK (EGN), 13.53 W/mK (recycled 2B) and 14.56 W/mK (BMEGN) and through-plane thermal conductivities of 0.76 W/mK (EGN), 0.84 W/mK (recycled 2B) and 0.95 W/mK (BMEGN) were experimentally measured. Anisotropies were calculated as 15.31, 15.98 and 16.95 for EGN, recycled 2B and BMEGN, respectively. In addition, the mechanical robustness of the developed TIMs is such that they are capable of repeatedly bending at 180 degrees with outstanding flexibility, including the low-cost renewable material of recycled lead-graphite pencils. For heat dissipating application in high-power electronics, the TIMs of recycled 2B are capable of effectively reducing temperatures to approximately 6.2 °C as favorably compared with thermal grease alone.

Advanced Thermal Interface Materials for Thermal Management

2018 ◽  
Author(s):  
Wei Yu ◽  
◽  
Changqing Liu ◽  
Lin Qiu ◽  
Ping Zhang ◽  
...  
Keyword(s):  
Thermal Management ◽  
Thermal Interface Materials ◽  
Thermal Interface ◽  
Interface Materials

Kinetic Adsorption of Humic Acids Mixture Obtained from Microalgae on Exfoliated Graphite Nanoplatelets

2018 ◽  
Vol 69 (1) ◽  
pp. 191-195
Author(s):  
Elena Radu ◽  
Elena Emilia Oprescu ◽  
Cristina Emanuela Enascuta ◽  
Catalina Calin ◽  
Rusandica Stoica ◽  
...  
Keyword(s):  
Humic Acid ◽  
Humic Acids ◽  
Alkali Treatment ◽  
Exfoliated Graphite ◽  
Acid Mixture ◽  
Acidic Ph ◽  
Graphite Nanoplatelets ◽  
Mixture Concentration ◽  
Ft Ir ◽  
Exfoliated Graphite Nanoplatelets

The dehydration of polysaccharides fraction in the presence of acid catalysts, is a chemical process in which results as secondary product humic matter. In our work, the humic acid mixture was for the first time based on our knowledge extracted from defatted microalgae biomass rich in polysaccharides by standard alkali treatment, followed by precipitation at acidic pH. The dried humic acid mixture has been characterized using infrared spectroscopic measurements (FT-IR). Exfoliated graphite nanoplatelets (xGnP) were used as new adsorbents for this type of humic acids mixture, their adsorption being investigated. The effect of several parameters such as: contact time, concentration of humic acid mixture, concentration of xGnP, temperature and pH of the solutions were studied. The process of adsorption took place with good results, in the following conditions: at a concentration of humic acid mixture of 18.6 mg L-1, an xGnP amount of 0.01 mg in 25 mL of solution, at a temperature of 25 �� and at acidic pH values, in aqueous solution.

scholarly journals Carbon Nanotube Films for Energy Applications

Energies ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 1890
Author(s):  
Monika Rdest ◽  
Dawid Janas
Keyword(s):  
Carbon Nanotube ◽  
Mechanical Energy ◽  
Research Community ◽  
Thermal Interface Materials ◽  
Thermal Interface ◽  
Conductive Coatings ◽  
Storage Devices ◽  
Energy Applications ◽  
Wide Range ◽  
Interface Materials

This perspective article describes the application opportunities of carbon nanotube (CNT) films for the energy sector. Up to date progress in this regard is illustrated with representative examples of a wide range of energy management and transformation studies employing CNT ensembles. Firstly, this paper features an overview of how such macroscopic networks from nanocarbon can be produced. Then, the capabilities for their application in specific energy-related scenarios are described. Among the highlighted cases are conductive coatings, charge storage devices, thermal interface materials, and actuators. The selected examples demonstrate how electrical, thermal, radiant, and mechanical energy can be converted from one form to another using such formulations based on CNTs. The article is concluded with a future outlook, which anticipates the next steps which the research community will take to bring these concepts closer to implementation.

Sign in / Sign up

Export Citation Format

Share Document