Characterization of Silver Nanowire Layers in the Terahertz Frequency Range

Thin layers of silver nanowires are commonly studied for transparent electronics. However, reports of their terahertz (THz) properties are scarce. Here, we present the electrical and optical properties of thin silver nanowire layers with increasing densities at THz frequencies. We demonstrate that the absorbance, transmittance and reflectance of the metal nanowire layers in the frequency range of 0.2 THz to 1.3 THz is non-monotonic and depends on the nanowire dimensions and filling factor. We also present and validate a theoretical approach describing well the experimental results and allowing the fitting of the THz response of the nanowire layers by a Drude–Smith model of conductivity. Our results pave the way toward the application of silver nanowires as a prospective material for transparent and conductive coatings, and printable antennas operating in the terahertz range—significant for future wireless communication devices.

Magnetoimpedance of CoFeCrSiB Ribbon-Based Sensitive Element with FeNi Covering: Experiment and Modeling

Soft magnetic materials are widely requested in electronic and biomedical applications. Co-based amorphous ribbons are materials which combine high value of the magnetoimpedance effect (MI), high sensitivity with respect to the applied magnetic field, good corrosion stability in aggressive environments, and reasonably low price. Functional properties of ribbon-based sensitive elements can be modified by deposition of additional magnetic and non-ferromagnetic layers with required conductivity. Such layers can play different roles. In the case of magnetic biosensors for magnetic label detection, they can provide the best conditions for self-assembling processes in biological experiments. In this work, magnetic properties and MI effect were studied for the cases of rapidly quenched Co67Fe3Cr3Si15B12 amorphous ribbons and magnetic Fe20Ni80/Co67Fe3Cr3Si15B12/Fe20Ni80 composites obtained by deposition of Fe20Ni80 1 μm thick films onto both sides of the ribbons by magnetron sputtering technique. Their comparative analysis was used for finite element computer simulations of MI responses with different types of magnetic and conductive coatings. The obtained results can be useful for the design of MI sensor development, including MI biosensors for magnetic label detection.

CREATION OF ELECTRIC CONDUCTIVE COATINGS USING GAS-DYNAMIC SPRAYING

The article presents the results of research on the processes of creating conductive coatings based on copper and aluminum in order to determine the interaction of components on each other during cold gas-dynamic spraying (CGDS) and substantiate the method of introducing an additional component to obtain the desired composite coating. In particular, under conditions when the copper sputtering coefficient is almost zero (at a working air temperature of 300 °C), it is the search for the experimental dependence of the sputtering coefficient on the percentage of copper and aluminum powders in the sprayed mixture, determining their residual content in the coating and then calculating based on these data, the sputtering coefficients of copper and aluminum. The CGDS method obtained samples with composite coatings from mixtures of aluminum and copper powders at different initial mass concentrations of aluminum (from 0 to 100%, in increments of 10%) Other things being equal (air pressure 0,6 MPa, air heating temperature 300 ° C) . The spraying ratio of the mixture and the residual content of the components in the obtained composite coatings were measured. Data on the residual content of the components in the coating allows you to select the composition of the source powder required to obtain a given content of components in the coating. The dependences of the sputtering coefficients of copper and aluminum on the mass content of aluminum in the sprayed mixture are found. At an initial concentration of aluminum less than 66%. the coefficient of copper sputtering is higher than the coefficient of sputtering of aluminum. Both increase monotonically with increasing aluminum concentration until it reaches 61%. At high concentrations of aluminum (more than 66%) the spray coefficients of copper, aluminum and their mixtures coincide. The obtained data on the residual content of the components in the coating allows you to select the composition of the source powder required to obtain a given content of components in the coating. For example, the maximum residual copper content (~ 95%) can be obtained by adding to the source powder 30-40% aluminum. The obtained results confirm the interaction of the components on each other and justify the method of introducing an additional component to obtain a composite coating containing a component that is difficult to spray.

Импульсный магнитный контроль толщины металлических покрытий

The research results of the characteristics of magneto-inductive thickness gauges measuring transducers using harmonic excitation currents for the case of inspecting electrically conductive coatings are presented, on the basis of which a transducing algorithm is proposed and described in detail, which involves pulsed excitation of a magnetic field and the use of the induced EMF area as a primary informative parameter when suppressing the influence of network and pulse noise, used in serial thickness gauges of metallic non-ferromagnetic coatings on ferromagnetic substrates.

Research and Analysis of Graphene Coatings Based on Knowledge Mapping

Graphene coating is a new type of coating made by using the unique structural properties of graphene. It has broad application prospects of anticorrosive coatings, conductive coatings and heat-dissipating coatings. In order to study the development of graphene coating technology research, we use CiteSpace information visualization software, based on the literature of 8 813 articles in the research and application of graphene coatings in Web of Science database from 2010 to 2018. From the perspective of literature measurement, we apply the knowledge map to research the national, discipline and related hotspot analysis of graphene coating research, cited literatures and research frontier status. By comparing and analyzing the literature information on the field of graphene coating research and application at home and abroad, the research progresses and development trend of graphene coatings can be evaluated from the disciplinary distribution and research fronts. It is pointed out that the wear resistance of graphene coatings is the focus of the future research.