Preparation of Garnet-Type Li7 − 3xAlxLa3Zr2O12 at Lower Temperature by Using Powders of Mixed Pre-treatment Conditions

2018 ◽  
Vol 28 (5) ◽  
pp. 2023-2027 ◽  
Author(s):  
Xiaojuan Lu ◽  
Dongyu Yang
2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Vahideh Yari ◽  
Zeynab Roein ◽  
Atefeh Sabouri

AbstractThe Anemone genus is a tuberous geophyte which undergoes a dormancy period during unfavorable environmental conditions for growth. Five species of the Anemone genus naturally grow in several regions of Iran. The diverse uses of Anemone in gardens for landscaping, cut flowers, and potted plants indicate its high ornamental potential. Its dormancy and flowering are influenced by various factors. The present paper was conducted to explore the flowering behavior of Anemone accessions in response to different pre-treatments. For this purpose, tubers of 18 Anemone accessions (A. coronaria and A. biflora) were collected from natural regions of six provinces in Iran. These tubers were subjected to different conditions of non-chilling (20 °C, 90 days), chilling (4 °C, 90 days), GA3 (150 mgL-1; 24 h), and 5-azaCitidine (5-azaC; 40 µM; 24 h) prior to the cultivation. Most of the accessions were able to enter the flowering stage without chilling. The shortest period for the sprouting of tubers (16.89 ± 7.83 days) belonged to 5-azaC pre-treatment. In addition, this treatment accelerated the flowering time (about 30 days earlier) and diameter of the stem, bud, and flower. Morphological characteristics, such as stem height, number of leaves, bud, and petal and the longevity of flowers on the plant were significantly affected by GA3 pre-treatment. Our results indicated a positive correlation between flower length, stem height, and stem diameter with flower longevity under different pre-treatment conditions. The present study demonstrated that accessions Anm3, Anm12, and Anm18 had ornamental values higher than the population mean across four conditions.


2018 ◽  
Vol 10 (3) ◽  
pp. 223-232
Author(s):  
G.J. Fadimu ◽  
L.O. Sanni ◽  
A.A. Adebowale ◽  
S.O. Kareem ◽  
O.P. Sobukola ◽  
...  

2020 ◽  
Vol 71 (1) ◽  
pp. 19-27
Author(s):  
Günay Özbay ◽  
Caglar Cekic ◽  
Muhammad Syarhabil Ahmad ◽  
Erkan Sami Kokten

In the present study, bio-oil produced from vacuum pyrolysis of woody biomass has been investigated as a source of chemical feedstock. Bio-based resins were produced using the bio- oil with phenol substitutions ranging from 10 to 30 wt%. The conventional GC/MS analysis was carried out for the evaluation of the chemical composition of bio-oil. TGA, DSC and FT-IR analyses were used in order to characterize the bio-oil-phenol-formaldehyde (BPF) resins. The bonding quality of wood samples bonded with the BPF resins was investigated under different pre-treatment conditions. The highest shear strength was observed for the control samples bonded with the laboratory PF resin. As the amount of bio-oil was increased up to 30 wt%, the shear strength of the samples decreased from 12.08 to 11.76 N/mm2. The bonding performance was not negatively affected by the combination of bio-oil under dry conditions. According to TS EN 12765 standard, the relevant performance requirements for bonded samples under dry conditions must be at least 10 N/mm2. Relating to the standard, all samples bonded with BPF resins obtained the requirements for durability class C1. Under wet conditions, the bonding performance was negatively affected by the addition of bio-oil. However, the BPF resins fulfilled the durability requirements for C1, C2, and C3 specified in EN 12765 (2002).


2019 ◽  
Vol 13 (1) ◽  
pp. 271-285 ◽  
Author(s):  
Emily T. Kostas ◽  
Daniel A. White ◽  
David J. Cook

Abstract This study describes the method development for bioethanol production from three species of seaweed. Laminaria digitata, Ulva lactuca and for the first time Dilsea carnosa were used as representatives of brown, green and red species of seaweed, respectively. Acid thermo-chemical and entirely aqueous (water) based pre-treatments were evaluated, using a range of sulphuric acid concentrations (0.125–2.5 M) and solids loading contents (5–25 % [w/v]; biomass: reactant) and different reaction times (5–30 min), with the aim of maximising the release of glucose following enzyme hydrolysis. A pre-treatment step for each of the three seaweeds was required and pre-treatment conditions were found to be specific to each seaweed species. Dilsea carnosa and U. lactuca were more suited with an aqueous (water-based) pre-treatment (yielding 125.0 and 360.0 mg of glucose/g of pre-treated seaweed, respectively), yet interestingly non pre-treated D. carnosa yielded 106.4 g g−1 glucose. Laminaria digitata required a dilute acid thermo-chemical pre-treatment in order to liberate maximal glucose yields (218.9 mg glucose/g pre-treated seaweed). Fermentations with S. cerevisiae NCYC2592 of the generated hydrolysates gave ethanol yields of 5.4 g L−1, 7.8 g L−1 and 3.2 g L−1 from D. carnosa, U. lactuca and L. digitata, respectively. This study highlighted that entirely aqueous based pre-treatments are effective for seaweed biomass, yet bioethanol production alone may not make such bio-processes economically viable at large scale.


2019 ◽  
Vol 249 ◽  
pp. 109397 ◽  
Author(s):  
Wonbae Lee ◽  
Seyong Park ◽  
Fenghao Cui ◽  
Moonil Kim

Sign in / Sign up

Export Citation Format

Share Document