Suspension Plasma-Sprayed Fluoridated Hydroxyapatite/Calcium Silicate Composite Coatings for Biomedical Applications

2019 ◽  
Vol 28 (5) ◽  
pp. 1025-1038 ◽  
Author(s):  
Sheng-jian Zhou ◽  
Yu Bai ◽  
Wen Ma ◽  
Wei-dong Chen
Keyword(s):  
Calcium Silicate ◽  
Biomedical Applications ◽  
Composite Coatings ◽  
Fluoridated Hydroxyapatite ◽  
Plasma Sprayed

scholarly journals Microstructural Charactistics of Plasma Sprayed NiCrBSi Coatings and Their Wear and Corrosion Behaviors

Coatings ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 170
Author(s):  
Songqiang Huang ◽  
Jingzhong Zhou ◽  
Kuoteng Sun ◽  
Hailiang Yang ◽  
Weichen Cai ◽  
...  
Keyword(s):  
Laser Scanning ◽  
Acid Corrosion ◽  
Composite Coatings ◽  
Atmospheric Plasma ◽  
Confocal Laser ◽  
Formation Mechanisms ◽  
Temperature Oxidation ◽  
Surface Protection ◽  
Plasma Sprayed ◽  
Nicrbsi Coatings

Nickel-based alloys are commonly used as protective coating materials for surface protection applications owing to their superior resistance to corrosion, wear and high-temperature oxidation. It is urgent to study the fundamental mechanism between the structure and corrosion properties of the Nickel-base composite coatings. This paper, therefore, focuses on clarifying the mechanisms of the microstructure influencing the acid corrosion and mechanical characteristics of the as-sprayed NiCrBSi coating and post-heat-treated coating. The formation mechanisms of the amorphous phase of flat particles during the plasma spray process were studied by using X-ray diffraction analysis, Raman spectroscopy and confocal laser scanning microscope at first. Then the evolutionary process of the corrosion structure and phase of the coating in the accelerated corrosion experiment is directly visualized by using scanning electron microscopy and energy spectrum analysis. The mechanical properties of the amorphous NiCrBSi coatings are lastly measured by microhardness and friction wear tests. The critical phenomena and results help to elucidate the relative influence of the surface features of atmospheric plasma sprayed coatings on acid corrosion responses and wear resistance, aiming at contributing to the development of a protective technique for electrical engineering.

Evaluation of Slurry Erosive Wear Performance of Plasma-Sprayed Flyash-TiO2 Composite Coatings

2021 ◽  
Vol 7 (3) ◽  
Author(s):  
R. Keshavamurthy ◽  
B. E. Naveena ◽  
C. S. Ramesh ◽  
M. R. Haseebuddin
Keyword(s):  
Composite Coatings ◽  
Erosive Wear ◽  
Wear Performance ◽  
Plasma Sprayed

scholarly journals Layer-by-Layer Self-Assembly Composite Coatings for Improved Corrosion and Wear Resistance of Mg Alloy for Biomedical Applications

Coatings ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 515
Author(s):  
Tongfang Liu ◽  
Song Rui ◽  
Sheng Li
Keyword(s):  
Wear Resistance ◽  
Self Assembly ◽  
Biomedical Applications ◽  
Composite Coatings ◽  
Covalent Bond ◽  
Mg Alloys ◽  
Mg Alloy ◽  
Layer By Layer ◽  
Corrosion Propagation ◽  
Chemical Linkage

Mg alloys are promising biomedical metal due to their natural degradability, good processability, and favorable mechanical properties. However, the poor corrosion resistance limits their further clinical applications. In this study, the combined strategies of surface chemical treatment and layer-by-layer self-assembly were used to prepare composite coatings on Mg alloys to improve the biocorrosion resistance. Specially, alkalized AZ91 Mg alloy generated chemical linkage with silane via Si–O–Mg covalent bond at the interface. Subsequently, Si–OH group from silane formed a crosslinked silane layer by Si–O–Si network. Further chemical assembly with graphene oxide (GO), lengthened the diffusion pathway of corrosive medium. The chemically assembled composite coatings could firmly bond to Mg alloy substrate, which persistently and effectively acted as compact barriers against corrosion propagation. Improved biocorrosion resistance of AZ91 Mg alloy with self-assembly composite coatings of silane/GO was subsequently confirmed by immersion tests. Besides, the Mg alloy exhibited good wear resistance due to outside layer of GO with a lubricant effect. Cell viability of higher than 75% had also been found for the alloy with self-assembly composite coatings, which showed good cytocompatibility.

Fabrication and Ablation Behavior of Plasma Sprayed ZrC-W Composite Coatings

2014 ◽  
Vol 602-603 ◽  
pp. 552-555
Author(s):  
Dan Lu ◽  
Ya Ran Niu ◽  
Xue Lian Ge ◽  
Xue Bing Zheng ◽  
Guang Chen
Keyword(s):  
Thermal Conductivity ◽  
Thermal Shock ◽  
Plasma Spray ◽  
Composite Coatings ◽  
Lamellar Microstructure ◽  
Atmospheric Plasma Spray ◽  
Atmospheric Plasma ◽  
Plasma Flame ◽  
Plasma Sprayed ◽  
Zrc Coating

In this work, atmospheric plasma spray (APS) technology was applied to fabricate ZrC-W composite coatings. The microstructure of the composite coatings was characterized. The influence of W content on the ablation-resistant and thermal shock properties of ZrC-W composite coatings was evaluated using a plasma flame. The results show that the ZrC-W composite coatings had typically lamellar microstructure, which was mainly made up of cubic ZrC, cubic W and a small amount of tetragonal ZrO2. The ZrC-W coatings had improved ablation resistant and thermal shock properties compared with those of the pure ZrC coating. It was supposed that the improved density, thermal conductivity and toughness of the composite coatings contributed to this phenomenon.

Electrodeposition of MgO/Calcium Phosphate Composite Coatings on Titanium for Biomedical Applications

2013 ◽  
Vol 785-786 ◽  
pp. 872-876
Author(s):  
Yong Huang ◽  
Shu Guang Han ◽  
Ya Jing Yan ◽  
Xiao Feng Pang
Keyword(s):  
Corrosion Resistance ◽  
Phase Composition ◽  
Calcium Phosphate ◽  
Biomedical Applications ◽  
Lower Layer ◽  
Composite Coatings ◽  
Polarization Test ◽  
Coated Surface ◽  
Bare Titanium ◽  
Superior Corrosion Resistance

This work elucidated corrosion resistance of the electrodeposited MgO/calcium phosphate (Ca-P/MgO) films on titanium (Ti). The microstructure, phase composition, and corrosion resistance of the films were studied. Results revealed that The Ca-P/MgO composite coatings were rough and inhomogeneous, the upper layer was floral-like crystals or flakes agglomerates morphology, and the lower layer was needle-like crystals which were mutually cross linked. The coating was very dense, and the content of Mg was about 0.3 wt%. Potentiodynamic polarization test manifested that the Ca-P/MgO-coated surface exhibited superior corrosion resistance than the bare titanium.

Sign in / Sign up

Export Citation Format

Share Document