Numerical investigation of influence of under- and over- treatment on residual stress state induced by HFMI

2021 ◽  
Author(s):  
Yuki Banno ◽  
Koji Kinoshita ◽  
Zuheir Barsoum
Keyword(s):  
Residual Stress ◽  
Stress State ◽  
Numerical Investigation ◽  
Residual Stress State

Numerical investigation of the WC re-precipitation impact on the residual stress state in WC20 wt.-%Co hardmetal

2019 ◽  
Vol 84 ◽  
pp. 105003
Author(s):  
Wolfgang Kayser ◽  
Stanley van Kempen ◽  
Alexander Bezold ◽  
Mirko Boin ◽  
Robert Wimpory ◽  
...  
Keyword(s):  
Residual Stress ◽  
Stress State ◽  
Numerical Investigation ◽  
Residual Stress State

scholarly journals Influence of Steel Grain Size on Residual Stress in Grinding Processing

2010 ◽  
Vol 638-642 ◽  
pp. 2389-2394 ◽  
Author(s):  
Masahide Gotoh ◽  
Katsuhiro Seki ◽  
M. Shozu ◽  
Hajime Hirose ◽  
Toshihiko Sasaki
Keyword(s):  
Mechanical Properties ◽  
Residual Stress ◽  
Grain Size ◽  
Stress State ◽  
Mechanical Grinding ◽  
Fine Grained ◽  
Residual Stress State ◽  
Analysis Methods ◽  
Average Grain Size ◽  
Fine Grained Steels

The fine-grained rolling steels NFG600 and the conventional usual rolling steels SM490 were processed by sand paper polishing and mechanical grinding to compare the residual stress generated after processing. The average grain size of NFG600 and SM490 is 3 μm and 15μm respectively. Therefore improvement of mechanical properties for such fine-grained steels is expected, it is important to understand the residual stress state of new fine-grained materials with processing. In this study, multi axial stresses of two kinds of specimens after polishing and grinding were measured by three kinds of analysis methods including cos-ψ method. As a result, as for σ33, the stress of NFG was compression, though that of SM490 was tension.

About Residual Stress State of Castings: The Case of HPDC Parts and Possible Advantages through Semi-Solid Processes

2022 ◽  
Vol 327 ◽  
pp. 272-278
Author(s):  
Elisa Fracchia ◽  
Federico Simone Gobber ◽  
Claudio Mus ◽  
Yuji Kobayashi ◽  
Mario Rosso
Keyword(s):  
Residual Stress ◽  
Stress State ◽  
Residual Stresses ◽  
Casting Process ◽  
Ray Method ◽  
Premature Failure ◽  
Thin Walls ◽  
Residual Stress State ◽  
Semi Solid ◽  
Pressure Die Casting

Nowadays, one of the most crucial focus in the aluminium-foundry sector is the production of high-quality castings. Mainly, High-Pressure Die Casting (HPDC) is broadly adopted, since by this process is possible to realize aluminium castings with thin walls and high specific mechanical properties. On the other hand, this casting process may cause tensile states into the castings, namely residual stresses. Residual stresses may strongly affect the life of the product causing premature failure of the casting. Various methods can assess these tensile states, but the non-destructive X-Ray method is the most commonly adopted. Namely, in this work, the residual stress analysis has been performed through Sinto-Pulstec μ-X360s. Detailed measurements have been done on powertrain components realized in aluminium alloy EN AC 46000 through HPDC processes to understand and prevent dangerous residual stress state into the aluminium castings. Furthermore, a comparison with stresses induced by Rheocasting processes is underway. In fact, it is well known that Semi-Solid metal forming combines the advantages of casting and forging, solving safety and environmental problems and possibly even the residual stress state can be positively affected.

scholarly journals Analysis of the Influence of Surface Modifications on the Fatigue Behavior of Hot Work Tool Steel Components

Materials ◽  
2021 ◽  
Vol 14 (23) ◽  
pp. 7324
Author(s):  
Thomas Wild ◽  
Timo Platt ◽  
Dirk Biermann ◽  
Marion Merklein
Keyword(s):  
Residual Stress ◽  
Stress State ◽  
Surface Integrity ◽  
Fatigue Behavior ◽  
Hot Forging ◽  
Surface Modifications ◽  
Bending Test ◽  
Fatigue Properties ◽  
Machining Processes ◽  
Residual Stress State

Hot work tool steels (HWS) are widely used for high performance components as dies and molds in hot forging processes, where extreme process-related mechanical and thermal loads limit tool life. With the functionalizing and modification of tool surfaces with tailored surfaces, a promising approach is given to provide material flow control resulting in the efficient die filling of cavities while reducing the process forces. In terms of fatigue properties, the influence of surface modifications on surface integrity is insufficiently studied. Therefore, the potential of the machining processes of high-feed milling, micromilling and grinding with regard to the implications on the fatigue strength of components made of HWS (AISI H11) hardened to 50 ± 1 HRC was investigated. For this purpose, the machined surfaces were characterized in terms of surface topography and residual stress state to determine the surface integrity. In order to analyze the resulting fatigue behavior as a result of the machining processes, a rotating bending test was performed. The fracture surfaces were investigated using fractographic analysis to define the initiation area and to identify the source of failure. The investigations showed a significant influence of the machining-induced surface integrity and, in particular, the induced residual stress state on the fatigue properties of components made of HWS.

Residual Stress State and Fatigue Behaviour of Laser Shock Peened Titanium Alloys

2006 ◽  
pp. 129-134
Author(s):  
I. Altenberger ◽  
Yuji Sano ◽  
M.A. Cherif ◽  
Ivan Nikitin ◽  
Berthold Scholtes
Keyword(s):  
Residual Stress ◽  
Stress State ◽  
Titanium Alloys ◽  
Fatigue Behaviour ◽  
Laser Shock ◽  
Residual Stress State

Hydration and radiation effects on the residual stress state of cortical bone

2013 ◽  
Vol 9 (12) ◽  
pp. 9503-9507 ◽  
Author(s):  
Patrick K.M. Tung ◽  
Stephen Mudie ◽  
John E. Daniels
Keyword(s):  
Residual Stress ◽  
Stress State ◽  
Cortical Bone ◽  
Radiation Effects ◽  
Residual Stress State
Sign in / Sign up

Export Citation Format

Share Document