scholarly journals Mechanical properties of graphene oxide–silk fibroin bionanofilms via nanoindentation experiments and finite element analysis

Friction ◽  
2021 ◽  
Author(s):  
Hyeonho Cho ◽  
Joonho Lee ◽  
Hyundo Hwang ◽  
Woonbong Hwang ◽  
Jin-Gyun Kim ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Graphene Oxide ◽  
Water Vapor ◽  
Silk Fibroin ◽  
Annealing Process ◽  
Indentation Modulus ◽  
Element Analysis ◽  
Vapor Annealing

AbstractUnderstanding the mechanical properties of bionanofilms is important in terms of identifying their durability. The primary focus of this study is to examine the effect of water vapor annealed silk fibroin on the indentation modulus and hardness of graphene oxide–silk fibroin (GO–SF) bionanofilms through nanoindentation experiments and finite element analysis (FEA). The GO–SF bionanofilms were fabricated using the layer-by-layer technique. The water vapor annealing process was employed to enhance the interfacial properties between the GO and SF layers, and the mechanical properties of the GO–SF bionanofilms were found to be affected by this process. By employing water vapor annealing, the indentation modulus and hardness of the GO–SF bionanofilms can be improved. Furthermore, the FEA models of the GO–SF bionanofilms were developed to simulate the details of the mechanical behaviors of the GO–SF bionanofilms. The difference in the stress and strain distribution inside the GO–SF bionanofilms before and after annealing was analyzed. In addition, the load-displacement curves that were obtained by the developed FEA model conformed well with the results from the nanoindentation tests. In summary, this study presents the mechanism of improving the indentation modulus and hardness of the GO–SF bionanofilms through the water vapor annealing process, which is established with the FEA simulation models.

Three-dimensional finite element analysis of the effects of anisotropy on bone mechanical properties measured by nanoindentation

2004 ◽  
Vol 19 (1) ◽  
pp. 114-123 ◽  
Author(s):  
Z. Fan ◽  
J.Y. Rho ◽  
J.G. Swadener
Keyword(s):  
Mechanical Properties ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Cortical Bone ◽  
Three Dimensional ◽  
Indentation Modulus ◽  
Element Analysis ◽  
Fea Model ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

A three-dimensional finite element analysis (FEA) model with elastic–plastic anisotropy was built to investigate the effects of anisotropy on nanoindentation measurements for cortical bone. The FEA model has demonstrated a capability to capture the cortical bone material response under the indentation process. By comparison with the contact area obtained from monitoring the contact profile in FEA simulations, the Oliver–Pharr method was found to underpredict or overpredict the contact area due to the effects of anisotropy. The amount of error (less than 10% for cortical bone) depended on the indentation orientation. The indentation modulus results obtained from FEA simulations at different surface orientations showed a trend similar to experimental results and were also similar to moduli calculated from a mathematical model. The Oliver–Pharr method has been shown to be useful for providing first-order approximations in the analysis of anisotropic mechanical properties of cortical bone, although the indentation modulus is influenced by anisotropy.

Finite Element Analysis of Reinforced Concrete Beams with Exterior FRP Shell

2011 ◽  
Vol 243-249 ◽  
pp. 1461-1465
Author(s):  
Chuan Min Zhang ◽  
Chao He Chen ◽  
Ye Fan Chen
Keyword(s):  
Mechanical Properties ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Reinforced Concrete ◽  
Concrete Beams ◽  
Reinforced Concrete Beams ◽  
Test Results ◽  
Contact Interface ◽  
Accurate Calculation ◽  
Element Analysis

The paper makes an analysis of the reinforced concrete beams with exterior FRP Shell in Finite Element, and compares it with the test results. The results show that, by means of this model, mechanical properties of reinforced concrete beams with exterior FRP shell can be predicted better. However, the larger the load, the larger deviation between calculated values and test values. Hence, if more accurate calculation is required, issues of contact interface between the reinforced concrete beams and the FRP shell should be taken into consideration.

The equivalent method of double V-wing honeycombs on the in-plane dynamic impact

2021 ◽  
pp. 073168442199086
Author(s):  
Yunfei Qu ◽  
Dian Wang ◽  
Hongye Zhang
Keyword(s):  
Mechanical Properties ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Elastic Modulus ◽  
Energy Absorption ◽  
Width Ratio ◽  
Size Factor ◽  
Dynamic Impact ◽  
Element Analysis ◽  
Equivalent Method

The double V-wing honeycomb can be applied in many fields because of its lower mass and higher performance. In this study, the volume, in-plane elastic modulus and unit cell area of the double V-wing honeycomb were analytically derived, which became parts of the theoretical basis of the novel equivalent method. Based on mass, plateau load, in-plane elastic modulus, compression strain and energy absorption of the double V-wing honeycomb, a novel equivalent method mapping relationship between the thickness–width ratio and the basic parameters was established. The various size factor of the equivalent honeycomb model was denoted as n and constructed by the explicit finite element analysis method. The mechanical properties and energy absorption performance for equivalent honeycombs were investigated and compared with hexagonal honeycombs under dynamic impact. Numerical results showed a well coincidence for each honeycomb under dynamic impact before 0.009 s. Honeycombs with the same thickness–width ratio had similar mechanical properties and energy absorption characteristics. The equivalent method was verified by theoretical analysis, finite element analysis and experimental testing. Equivalent honeycombs exceeded the initial honeycomb in performance efficiency. Improvement of performance and weight loss reached 173.9% and 13.3% to the initial honeycomb. The double V-wing honeycomb possessed stronger impact resistance and better load-bearing capacity than the hexagonal honeycomb under impact in this study. The equivalent method could be applied to select the optimum honeycomb based on requirements and improve the efficiency of the double V-wing honeycomb.

Evaluation of the mechanical properties of SS-316L thin foils by small punch testing and finite element analysis

2015 ◽  
Vol 83 ◽  
pp. 75-84 ◽  
Author(s):  
S. Haroush ◽  
E. Priel ◽  
D. Moreno ◽  
A. Busiba ◽  
I. Silverman ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Element Analysis ◽  
Small Punch ◽  
Thin Foils

Structural Optimization Design of MR Fluid Clutch

2007 ◽  
Vol 546-549 ◽  
pp. 1673-1676 ◽  
Author(s):  
Wei Jia Meng ◽  
Zhan Wen Huang ◽  
Yan Ju Liu ◽  
Xiao Rong Wu ◽  
Yi Sun
Keyword(s):  
Magnetic Field ◽  
Mechanical Properties ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Optimization Design ◽  
Element Analysis ◽  
Mr Fluids ◽  
Magneto Rheological ◽  
Ferromagnetic Fluids ◽  
Ferromagnetic Particles

Magnetorheological (MR) fluids are suspensions of micron sized ferromagnetic particles dispersed in varying proportions of a variety of non-ferromagnetic fluids. MR fluids exhibit rapid, reversible and significant changes in their rheological (mechanical) properties while subjected to an external magnetic field. In this paper, a double-plate magneto-rheological fluid (MRF) clutch with controllable torque output have been designed. Electromagnetic finite element analysis is used to optimize the design of the clutch by using the commercial FEA software ANSYS.

Sign in / Sign up

Export Citation Format

Share Document