scholarly journals Metal powder bed fusion process chains: an overview of modelling techniques

2021 ◽  
Author(s):  
Shukri Afazov ◽  
Adam Roberts ◽  
Louise Wright ◽  
Prashant Jadhav ◽  
Adam Holloway ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Metal Powder ◽  
Surface Finishing ◽  
Topology Optimisation ◽  
Powder Bed Fusion ◽  
Powder Bed ◽  
Advantages And Disadvantages ◽  
Process Chains ◽  
Modelling Techniques ◽  
Research Domains

AbstractMetal powder bed fusion (MPBF) is not a standalone process, and other manufacturing technologies, such as heat treatment and surface finishing operations, are often required to achieve a high-quality component. To optimise each individual process for a given component, its progression through the full process chain must be considered and understood, which can be achieved through the use of validated models. This article aims to provide an overview of the various modelling techniques that can be utilised in the development of a digital twin for MPBF process chains, including methods for data transfer between physical and digital entities and uncertainty evaluation. An assessment of the current maturity of modelling techniques through the use of technology readiness levels is conducted to understand their maturity. Summary remarks highlighting the advantages and disadvantages in physics-based modelling techniques used in MPBF research domains  (i.e. prediction of: powder distortion; temperature; material properties; distortion; residual stresses; as well as topology optimisation), post-processing (i.e. modelling of: machining; heat treatment; and surface engineering), and digital twins (i.e. simulation of manufacturing process chains; interoperability; and computational performance) are provided. Future perspectives for the challenges in these MPBF research domains are also discussed and summarised.

Microstructure of Built Part Obtained by Powder Bed Fusion Process with Metal

2019 ◽  
Vol 825 ◽  
pp. 1-6
Author(s):  
Tatsuaki Furumoto ◽  
Kyota Egashira ◽  
Souta Matsuura ◽  
Makoto Nikawa ◽  
Masato Okada ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Metal Powder ◽  
Maraging Steel ◽  
Process Parameters ◽  
Steel Powder ◽  
Powder Bed Fusion ◽  
Laser Melting ◽  
Powder Bed ◽  
Suitable Heat Treatment ◽  
Deposited Metal

The influence of various process parameters on the building of maraging steel powder by the selective laser melting (SLM) processes is investigated. The microstructure in the built part was observed and the influence of the heat treatment was evaluated. As results, the depth of solidified layer was higher than that of deposited metal powder, and its value was influenced with the process parameters. The microstructure in the boundary between the built part and the substrate was quite different from the built part even if the suitable heat treatment was performed.

scholarly journals Carbon Particle In-Situ Alloying of the Case-Hardening Steel 16MnCr5 in Laser Powder Bed Fusion

Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 896
Author(s):  
Matthias Schmitt ◽  
Albin Gottwalt ◽  
Jakob Winkler ◽  
Thomas Tobie ◽  
Georg Schlick ◽  
...  
Keyword(s):  
Laser Beam ◽  
Mechanical Strength ◽  
Carbon Content ◽  
Metal Powder ◽  
Case Hardening ◽  
Powder Bed Fusion ◽  
Powder Bed ◽  
Carbon Particles ◽  
Case Hardening Steel

The carbon content of steel affects many of its essential properties, e.g., hardness and mechanical strength. In the powder bed fusion process of metals using a laser beam (PBF-LB/M), usually, pre-alloyed metal powder is solidified layer-by-layer using a laser beam to create parts. A reduction of the carbon content in steels is observed during this process. This study examines adding carbon particles to the metal powder and in situ alloying in the PBF-LB/M process as a countermeasure. Suitable carbon particles are selected and their effect on the particle size distribution and homogeneity of the mixtures is analysed. The workability in PBF-LB is then shown. This is followed by an evaluation of the resulting mechanical properties (hardness and mechanical strength) and microstructure in the as-built state and the state after heat treatment. Furthermore, potential use cases like multi-material or functionally graded parts are discussed.

scholarly journals Laser Powder Bed Fusion Processing of Fe-Mn-Al-Ni Shape Memory Alloy—On the Effect of Elevated Platform Temperatures

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 185
Author(s):  
Felix Clemens Ewald ◽  
Florian Brenne ◽  
Tobias Gustmann ◽  
Malte Vollmer ◽  
Philipp Krooß ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Crack Formation ◽  
Microstructural Analysis ◽  
Tensile Load ◽  
Grain Structure ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Cyclic Heat Treatment ◽  
Powder Bed ◽  
Cyclic Heat

In order to overcome constraints related to crack formation during additive processing (laser powder bed fusion, L-BPF) of Fe-Mn-Al-Ni, the potential of high-temperature L-PBF processing was investigated in the present study. The effect of the process parameters on crack formation, grain structure, and phase distribution in the as-built condition, as well as in the course of cyclic heat treatment was examined by microstructural analysis. Optimized processing parameters were applied to fabricate cylindrical samples featuring a crack-free and columnar grained microstructure. In the course of cyclic heat treatment, abnormal grain growth (AGG) sets in, eventually promoting the evolution of a bamboo like microstructure. Testing under tensile load revealed a well-defined stress plateau and reversible strains of up to 4%.

scholarly journals Gold, Silver, and Electrum Electroless Plating on Additively Manufactured Laser Powder-Bed Fusion AlSi10Mg Parts: A Review

Coatings ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 422
Author(s):  
Dana Ashkenazi ◽  
Alexandra Inberg ◽  
Yosi Shacham-Diamand ◽  
Adin Stern
Keyword(s):  
Additive Manufacturing ◽  
Low Cost ◽  
Ion Beam ◽  
Surface Finishing ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
Finishing Process ◽  
Gold Silver ◽  
3D Printed

Additive manufacturing (AM) revolutionary technologies open new opportunities and challenges. They allow low-cost manufacturing of parts with complex geometries and short time-to-market of products that can be exclusively customized. Additive manufactured parts often need post-printing surface modification. This study aims to review novel environmental-friendly surface finishing process of 3D-printed AlSi10Mg parts by electroless deposition of gold, silver, and gold–silver alloy (e.g., electrum) and to propose a full process methodology suitable for effective metallization. This deposition technique is simple and low cost method, allowing the metallization of both conductive and insulating materials. The AlSi10Mg parts were produced by the additive manufacturing laser powder bed fusion (AM-LPBF) process. Gold, silver, and their alloys were chosen as coatings due to their esthetic appearance, good corrosion resistance, and excellent electrical and thermal conductivity. The metals were deposited on 3D-printed disk-shaped specimens at 80 and 90 °C using a dedicated surface activation method where special functionalization of the printed AlSi10Mg was performed to assure a uniform catalytic surface yielding a good adhesion of the deposited metal to the substrate. Various methods were used to examine the coating quality, including light microscopy, optical profilometry, XRD, X-ray fluorescence, SEM–energy-dispersive spectroscopy (EDS), focused ion beam (FIB)-SEM, and XPS analyses. The results indicate that the developed coatings yield satisfactory quality, and the suggested surface finishing process can be used for many AM products and applications.

Toward Metamodels for Composable and Reusable Additive Manufacturing Process Models

2014 ◽  
Vol 136 (6) ◽  
Author(s):  
Paul Witherell ◽  
Shaw Feng ◽  
Timothy W. Simpson ◽  
David B. Saint John ◽  
Pan Michaleris ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Metal Powder ◽  
Manufacturing Process ◽  
Process Model ◽  
Model Development ◽  
Process Models ◽  
Powder Bed Fusion ◽  
Powder Bed ◽  
Future Work ◽  
Am Processes

In this paper, we advocate for a more harmonized approach to model development for additive manufacturing (AM) processes, through classification and metamodeling that will support AM process model composability, reusability, and integration. We review several types of AM process models and use the direct metal powder bed fusion AM process to provide illustrative examples of the proposed classification and metamodel approach. We describe how a coordinated approach can be used to extend modeling capabilities by promoting model composability. As part of future work, a framework is envisioned to realize a more coherent strategy for model development and deployment.

Fast prediction of thermal distortion in metal powder bed fusion additive manufacturing: Part 1, a thermal circuit network model

2018 ◽  
Vol 22 ◽  
pp. 852-868 ◽  
Author(s):  
Hao Peng ◽  
Morteza Ghasri-Khouzani ◽  
Shan Gong ◽  
Ross Attardo ◽  
Pierre Ostiguy ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Metal Powder ◽  
Network Model ◽  
Thermal Distortion ◽  
Powder Bed Fusion ◽  
Powder Bed ◽  
Thermal Circuit ◽  
Fast Prediction

scholarly journals Studies of Post-Fabrication Heat Treatment of L-PBF-Inconel 718: Effects of Hold Time on Microstructure, Annealing Twins, and Hardness

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 266
Author(s):  
Wakshum M. Tucho ◽  
Vidar Hansen
Keyword(s):  
Heat Treatment ◽  
Solid Solution ◽  
Additive Manufacturing ◽  
Inconel 718 ◽  
Solution Heat Treatment ◽  
Hold Time ◽  
Powder Bed Fusion ◽  
Powder Bed ◽  
Annealing Twins ◽  
Complete Recrystallization

The widely adopted temperature for solid solution heat treatment (ST) for the conventionally fabricated Inconel 718 is 1100 °C for a hold time of 1 h or less. This ST scheme is, however, not enough to dissolve Laves and annihilate dislocations completely in samples fabricated with Laser metal powder bed fusion (L-PBF) additive manufacturing (AM)-Inconel 718. Despite this, the highest hardness obtained after aging for ST temperatures (970–1250 °C) is at 1100 °C/1 as we have ascertained in our previous studies. The unreleased residual stresses in the retained lattice defects potentially affect other properties of the material. Hence, this work aims to investigate if a longer hold time of ST at 1100 °C will lead to complete recrystallization while maintaining the hardness after aging or not. For this study, L-PBF-Inconel 718 samples were ST at 1100 °C at various hold times (1, 3, 6, 9, 16, or 24 h) and aged to study the effects on microstructure and hardness. In addition, a sample was directly aged to study the effects of bypassing ST. The samples (ST and aged) gain hardness by 43–49%. The high density of annealing twins evolved during 3 h of ST and only slightly varies for longer ST.

Sign in / Sign up

Export Citation Format

Share Document