A study on strontium niobate based piezo-resistive materials for high-temperature and high-pressure sensor applications

2019 ◽  
Vol 8 (1) ◽  
pp. 25-30 ◽  
Author(s):  
P. Sivagnanapalani ◽  
Benudhar Sahoo ◽  
Prasanta Kumar Panda
2014 ◽  
Vol 609-610 ◽  
pp. 1053-1059
Author(s):  
Zhong Ren ◽  
Qiu Lin Tan ◽  
Chen Li ◽  
Tao Luo ◽  
Ting Cai ◽  
...  

A wide range pressure sensor is designed based on the theoretical basis of LC series resonance circuit model to realize the wireless passive measurement in the harsh environment, such as high temperature and high pressure. The capacitive pressure sensitive device is devised by the technology of high-temperature co-fired ceramics (HTCC) to form nine density cavities in zirconia ceramic substrates, and thick film technology to print capacitance plates and planar spiral inductors. The theoretical calculation and simulation analysis of the designed sensor are made respectively under high pressure (10MPa) and temperature (600 °C), the results of which verify the feasibility of the design in a wide range of pressure for high-temperature applications, and provide the reliable theory basis for the fabrication of wide range pressure sensor.


2014 ◽  
Vol 472 ◽  
pp. 242-246
Author(s):  
Bo Jiang ◽  
Xing Lin Qi ◽  
Zhi Ning Zhao

MEMS technology has been widely used in military industry, in order to further expand the scope of the MEMS pressure sensor applications in military industry, to make fuze development toward miniaturization and intelligent, do the study on special fuze MEMS pressure sensor. Environment of MEMS pressure sensor application in fuze is analyzed, consist service treatment environment and using environment, which can provide indicators for the development of the sensor. The paper analyzes several key technology of the fuze MEMS pressure sensor, including the technique of high temperature resistant, acceleration compensation, leadless, high frequency resistant and overload resistant and so on. To sum up, the continuous development of MEMS technology can make its products meet the use environment of fuze, and the development trend of the fuze also needs the support of MEMS technology, so it is necessary and feasible to carry out the research of the fuze MEMS pressure sensor.


2021 ◽  
Author(s):  
Meiling Jia ◽  
Chenghan Yi ◽  
Yankun Han ◽  
Xin Li ◽  
Guoliang Xu ◽  
...  

Abstract Thin, lightweight, and flexible textile pressure sensors with the ability to precisely detect the full range of faint pressure (< 100 Pa), low pressure (in the range of KPa) and high pressure (in the range of MPa) are in significant demand to meet the requirements for applications in daily activities and more meaningfully in some harsh environments, such as high temperature and high pressure. However, it is still a major challenge to fulfill these requirements simultaneously in a single pressure sensor. Herein, a high-performance pressure sensor enabled by polyimide fiber fabric with functionalized carbon-nanotube (PI/FCNT) is obtained via a facile electrophoretic deposition (EPD) approach. High-density FCNT is evenly wrapped and chemically bonded to the fiber surface during the EPD process, forming a conductive hierarchical fiber/FCNT matrix. Benefiting from the abundant yet firm contacting points, point-to-point contacting mode, and high elastic modulus of both PI and CNT, the proposed PI/FCNT pressure sensor exhibits ultra-high sensitivity (3.57 MPa− 1), ultra-wide linearity (3.24 MPa), exceptionally broad sensing range (~ 45 MPa), and long-term stability (> 4000 cycles). Furthermore, under a high working temperature of 200 ºC, the proposed sensor device still shows an ultra-high sensitivity of 2.64 MPa− 1 within a wide linear range of 7.2 MPa, attributing to its intrinsic high-temperature-resistant properties of PI and CNT. Thanks to these merits, the proposed PI/FCNT(EPD) pressure sensor could serve as an E-skin device to monitor the human physiological information, precisely detect tiny and extremely high pressure, and can be integrated into an intelligent mechanical hand to detect the contact force under high-temperature (> 300 ºC), endowing it with high applicability in the fields of real-time health monitoring, intelligent robots, and harsh environments.


2010 ◽  
Vol 437 ◽  
pp. 397-401 ◽  
Author(s):  
Zhuang De Jiang ◽  
Li Bo Zhao ◽  
Yu Long Zhao ◽  
Yuan Hao Liu ◽  
Philip D. Prewett ◽  
...  

In order to solve pressure measurement problems in the fields of aerospace, petroleum and chemical industry, mobile and military industry, a oil-filled isolated piezoresistive high pressure sensor has been developed with the range of 0~100 MPa, and was able to work reliably under high temperature of above 200 °C. Based on MEMS (Micro Electro-Mechanical System) and SIMOX (Separation by Implantation of Oxygen) technology, the piezoresistive sensor chip has been developed. By high temperature packaging process, the oil-filled isolated high pressure sensor was fabricated with the sensor chip and corrugated diaphragm. The experimental results showed that the oil-filled isolated high pressure sensor had good performances under high temperature of 200 °C, such as linearity error of 0.07%FS, repeatability error of 0.04%FS, hysteresis error of 0.03%FS.


2020 ◽  
Vol 8 (47) ◽  
pp. 17107-17113
Author(s):  
Grace Dansoa Tabi ◽  
Joo Sung Kim ◽  
Benjamin Nketia-Yawson ◽  
Do Hwan Kim ◽  
Young-Yong Noh

A facile method to fabricate high-capacitance stretchable polyurethane ionogels is reported for organic transistor and pressure sensor applications, measuring remarkable mobility of ∼2 cm2 V−1 s−1 and a high-pressure sensitivity of 0.12 kPa−1.


Sign in / Sign up

Export Citation Format

Share Document