scholarly journals Hierarchical network enabled flexible textile pressure sensors with ultra-high sensitivity, ultra-wide linearity and high-temperature resistance

2021 ◽  
Author(s):  
Meiling Jia ◽  
Chenghan Yi ◽  
Yankun Han ◽  
Xin Li ◽  
Guoliang Xu ◽  
...  
Keyword(s):  
High Pressure ◽  
High Temperature ◽  
Pressure Sensor ◽  
High Performance ◽  
Full Range ◽  
Pressure Sensors ◽  
Fiber Surface ◽  
High Sensitivity ◽  
Harsh Environments ◽  
Point To Point

Abstract Thin, lightweight, and flexible textile pressure sensors with the ability to precisely detect the full range of faint pressure (< 100 Pa), low pressure (in the range of KPa) and high pressure (in the range of MPa) are in significant demand to meet the requirements for applications in daily activities and more meaningfully in some harsh environments, such as high temperature and high pressure. However, it is still a major challenge to fulfill these requirements simultaneously in a single pressure sensor. Herein, a high-performance pressure sensor enabled by polyimide fiber fabric with functionalized carbon-nanotube (PI/FCNT) is obtained via a facile electrophoretic deposition (EPD) approach. High-density FCNT is evenly wrapped and chemically bonded to the fiber surface during the EPD process, forming a conductive hierarchical fiber/FCNT matrix. Benefiting from the abundant yet firm contacting points, point-to-point contacting mode, and high elastic modulus of both PI and CNT, the proposed PI/FCNT pressure sensor exhibits ultra-high sensitivity (3.57 MPa− 1), ultra-wide linearity (3.24 MPa), exceptionally broad sensing range (~ 45 MPa), and long-term stability (> 4000 cycles). Furthermore, under a high working temperature of 200 ºC, the proposed sensor device still shows an ultra-high sensitivity of 2.64 MPa− 1 within a wide linear range of 7.2 MPa, attributing to its intrinsic high-temperature-resistant properties of PI and CNT. Thanks to these merits, the proposed PI/FCNT(EPD) pressure sensor could serve as an E-skin device to monitor the human physiological information, precisely detect tiny and extremely high pressure, and can be integrated into an intelligent mechanical hand to detect the contact force under high-temperature (> 300 ºC), endowing it with high applicability in the fields of real-time health monitoring, intelligent robots, and harsh environments.

scholarly journals Hierarchical network enabled flexible textile pressure sensor with ultra-broad response range and high-temperature resistance

2021 ◽  
Author(s):  
Meiling Jia ◽  
Chenghan Yi ◽  
Yankun Han ◽  
Xin Li ◽  
Guoliang Xu ◽  
...  
Keyword(s):  
High Pressure ◽  
High Temperature ◽  
Pressure Sensor ◽  
Full Range ◽  
Pressure Sensors ◽  
Fiber Surface ◽  
Harsh Environments ◽  
Temperature Resistance ◽  
High Temperature Resistance ◽  
Fiber Fabric

Abstract Thin, lightweight, and flexible textile pressure sensors with the ability to detect the full range of faint pressure (<100 Pa), low pressure (in the range of KPa) and high pressure (in the range of MPa) are in significant demand to meet the requirements for applications in daily activities and more meaningfully in some harsh environments, such as high temperature and high pressure. However, it is still a significant challenge to fulfill these requirements simultaneously in a single pressure sensor. Herein, a high-performance pressure sensor enabled by polyimide fiber fabric with functionalized carbon-nanotube (PI/FCNT) is obtained via a facile electrophoretic deposition (EPD) approach. High-density FCNT is evenly wrapped and chemically bonded to the fiber surface during the EPD process, forming a conductive hierarchical fiber/FCNT matrix. Benefiting from the large compressible region of PI fiber fabric, abundant yet firm contacting points, point-to-point contacting mode, and high elastic modulus of both PI and CNT, the proposed PI/FCNT pressure sensor can be customized and modulated to achieve both a wide linear ranges, ultra-broad sensing range, long-term stability and high-temperature resistance. Thanks to these merits, the proposed PI/FCNT(EPD) pressure sensor could monitor the human physiological information, detect tiny and extremely high pressure, can be integrated into an intelligent mechanical hand to detect the contact force under high-temperature (>300 ºC), endowing it with high applicability in the fields of real-time health monitoring, intelligent robots, and harsh environments.

scholarly journals A Ceramic Diffusion Bonding Method for Passive LC High-Temperature Pressure Sensor

Sensors ◽  
2018 ◽  
Vol 18 (8) ◽  
pp. 2676
Author(s):  
Chen Li ◽  
Boshan Sun ◽  
Yanan Xue ◽  
Jijun Xiong
Keyword(s):  
High Temperature ◽  
Pressure Sensor ◽  
Pressure Sensors ◽  
Alumina Ceramic ◽  
Harsh Environments ◽  
Ceramic Substrates ◽  
Integrated Technology ◽  
All Ceramic ◽  
Test Platform ◽  
Bonding Method

Alumina ceramic is a highly promising material for fabricating high-temperature pressure sensors. In this paper, a direct bonding method for fabricating a sensitive cavity with alumina ceramic is presented. Alumina ceramic substrates were bonded together to form a sensitive cavity for high-temperature pressure environments. The device can sense pressure parameters at high temperatures. To verify the sensitivity performance of the fabrication method in high-temperature environments, an inductor and capacitor were integrated on the ceramic substrate with the fabricated sensitive cavity to form a wireless passive LC pressure sensor with thick-film integrated technology. Finally, the fabricated sensor was tested using a system test platform. The experimental results show that the sensor can realize pressure measurements above 900 °C, confirming that the fabricated sensitive cavity has excellent sealing properties. Therefore, the direct bonding method can potentially be used for developing all-ceramic high-temperature pressure sensors for application in harsh environments.

scholarly journals Nano Carbon Black-Based High Performance Wearable Pressure Sensors

Nanomaterials ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 664 ◽  
Author(s):  
Junsong Hu ◽  
Junsheng Yu ◽  
Ying Li ◽  
Xiaoqing Liao ◽  
Xingwu Yan ◽  
...  
Keyword(s):  
Carbon Black ◽  
Pressure Sensor ◽  
High Performance ◽  
Large Scale ◽  
Pressure Sensors ◽  
High Sensitivity ◽  
Wearable Electronics ◽  
Atmospheric Pollutant ◽  
Piezoresistive Pressure Sensor ◽  
Nano Carbon

The reasonable design pattern of flexible pressure sensors with excellent performance and prominent features including high sensitivity and a relatively wide workable linear range has attracted significant attention owing to their potential application in the advanced wearable electronics and artificial intelligence fields. Herein, nano carbon black from kerosene soot, an atmospheric pollutant generated during the insufficient burning of hydrocarbon fuels, was utilized as the conductive material with a bottom interdigitated textile electrode screen printed using silver paste to construct a piezoresistive pressure sensor with prominent performance. Owing to the distinct loose porous structure, the lumpy surface roughness of the fabric electrodes, and the softness of polydimethylsiloxane, the piezoresistive pressure sensor exhibited superior detection performance, including high sensitivity (31.63 kPa−1 within the range of 0–2 kPa), a relatively large feasible range (0–15 kPa), a low detection limit (2.26 pa), and a rapid response time (15 ms). Thus, these sensors act as outstanding candidates for detecting the human physiological signal and large-scale limb movement, showing their broad range of application prospects in the advanced wearable electronics field.

scholarly journals Flexible and Highly Sensitive Pressure Sensors Based on Microstructured Carbon Nanowalls Electrodes

Nanomaterials ◽  
2019 ◽  
Vol 9 (4) ◽  
pp. 496 ◽  
Author(s):  
Xi Zhou ◽  
Yongna Zhang ◽  
Jun Yang ◽  
Jialu Li ◽  
Shi Luo ◽  
...  
Keyword(s):  
Pressure Sensor ◽  
High Performance ◽  
Limit Of Detection ◽  
Pressure Sensors ◽  
High Sensitivity ◽  
Physiological Signals ◽  
Healthcare Applications ◽  
Highly Sensitive ◽  
Carbon Nanowalls ◽  
Pressure Regime

Wearable pressure sensors have attracted widespread attention in recent years because of their great potential in human healthcare applications such as physiological signals monitoring. A desirable pressure sensor should possess the advantages of high sensitivity, a simple manufacturing process, and good stability. Here, we present a highly sensitive, simply fabricated wearable resistive pressure sensor based on three-dimensional microstructured carbon nanowalls (CNWs) embedded in a polydimethylsiloxane (PDMS) substrate. The method of using unpolished silicon wafers as templates provides an easy approach to fabricate the irregular microstructure of CNWs/PDMS electrodes, which plays a significant role in increasing the sensitivity and stability of resistive pressure sensors. The sensitivity of the CNWs/PDMS pressure sensor with irregular microstructures is as high as 6.64 kPa−1 in the low-pressure regime, and remains fairly high (0.15 kPa−1) in the high-pressure regime (~10 kPa). Both the relatively short response time of ~30 ms and good reproducibility over 1000 cycles of pressure loading and unloading tests illustrate the high performance of the proposed device. Our pressure sensor exhibits a superior minimal limit of detection of 0.6 Pa, which shows promising potential in detecting human physiological signals such as heart rate. Moreover, it can be turned into an 8 × 8 pixels array to map spatial pressure distribution and realize array sensing imaging.

scholarly journals High-Sensitivity Flexible Pressure Sensor-Based 3D CNTs Sponge for Human–Computer Interaction

Polymers ◽  
2021 ◽  
Vol 13 (20) ◽  
pp. 3465
Author(s):  
Jianli Cui ◽  
Xueli Nan ◽  
Guirong Shao ◽  
Huixia Sun
Keyword(s):  
Pressure Sensor ◽  
High Performance ◽  
Large Scale ◽  
Low Cost ◽  
Pressure Sensors ◽  
Chemical Vapor ◽  
High Sensitivity ◽  
Wearable Electronics ◽  
Wide Range ◽  
Flexible Pressure Sensors

Researchers are showing an increasing interest in high-performance flexible pressure sensors owing to their potential uses in wearable electronics, bionic skin, and human–machine interactions, etc. However, the vast majority of these flexible pressure sensors require extensive nano-architectural design, which both complicates their manufacturing and is time-consuming. Thus, a low-cost technology which can be applied on a large scale is highly desirable for the manufacture of flexible pressure-sensitive materials that have a high sensitivity over a wide range of pressures. This work is based on the use of a three-dimensional elastic porous carbon nanotubes (CNTs) sponge as the conductive layer to fabricate a novel flexible piezoresistive sensor. The synthesis of a CNTs sponge was achieved by chemical vapor deposition, the basic underlying principle governing the sensing behavior of the CNTs sponge-based pressure sensor and was illustrated by employing in situ scanning electron microscopy. The CNTs sponge-based sensor has a quick response time of ~105 ms, a high sensitivity extending across a broad pressure range (less than 10 kPa for 809 kPa−1) and possesses an outstanding permanence over 4,000 cycles. Furthermore, a 16-pixel wireless sensor system was designed and a series of applications have been demonstrated. Its potential applications in the visualizing pressure distribution and an example of human–machine communication were also demonstrated.

scholarly journals A Soft Pressure Sensor Array Based on a Conducting Nanomembrane

Micromachines ◽  
2021 ◽  
Vol 12 (8) ◽  
pp. 933
Author(s):  
Daekwang Jung ◽  
Kyumin Kang ◽  
Hyunjin Jung ◽  
Duhwan Seong ◽  
Soojung An ◽  
...  
Keyword(s):  
Pressure Sensor ◽  
High Performance ◽  
Sensor Array ◽  
Pressure Sensors ◽  
Strain Range ◽  
High Sensitivity ◽  
Critical Issue ◽  
Mechanical Stimuli ◽  
Highly Sensitive ◽  
Accumulated Strain

Although skin-like pressure sensors exhibit high sensitivity with a high performance over a wide area, they have limitations owing to the critical issue of being linear only in a narrow strain range. Various strategies have been proposed to improve the performance of soft pressure sensors, but such a nonlinearity issue still exists and the sensors are only effective within a very narrow strain range. Herein, we fabricated a highly sensitive multi-channel pressure sensor array by using a simple thermal evaporation process of conducting nanomembranes onto a stretchable substrate. A rigid-island structure capable of dissipating accumulated strain energy induced by external mechanical stimuli was adopted for the sensor. The performance of the sensor was precisely controlled by optimizing the thickness of the stretchable substrate and the number of serpentines of an Au membrane. The fabricated sensor exhibited a sensitivity of 0.675 kPa−1 in the broad pressure range of 2.3–50 kPa with linearity (~0.990), and good stability (>300 Cycles). Finally, we successfully demonstrated a mapping of pressure distribution.

Wearable and visual pressure sensors based on Zn2GeO4@polypyrrole nanowire aerogels

2017 ◽  
Vol 5 (42) ◽  
pp. 11018-11024 ◽  
Author(s):  
Jie Xue ◽  
Jiawei Chen ◽  
Jizhong Song ◽  
Leimeng Xu ◽  
Haibo Zeng
Keyword(s):  
Pressure Sensor ◽  
High Performance ◽  
Light Emitting Diode ◽  
Pressure Sensors ◽  
High Sensitivity ◽  
Light Emitting

A high-performance and tailorable pressure sensor based on the Zn2GeO4@PPy nanowire aerogel for applications in visual and wearable fields has been developed and show high sensitivity of the pressure sensor (0.38 kPa−1at pressure regions less than 1.5 kPa). We also combined the aerogels with Light Emitting Diode which make a visible sensor come true.

scholarly journals Simulation and Nonlinearity Optimization of a High-Pressure Sensor

Sensors ◽  
2020 ◽  
Vol 20 (16) ◽  
pp. 4419
Author(s):  
Ting Li ◽  
Haiping Shang ◽  
Weibing Wang
Keyword(s):  
High Pressure ◽  
Pressure Sensor ◽  
Pressure Sensors ◽  
Original Model ◽  
Ansys Software ◽  
Nonlinear Error ◽  
Sensor Model ◽  
Optimized Model ◽  
Simulation Results ◽  
Better Than

A pressure sensor in the range of 0–120 MPa with a square diaphragm was designed and fabricated, which was isolated by the oil-filled package. The nonlinearity of the device without circuit compensation is better than 0.4%, and the accuracy is 0.43%. This sensor model was simulated by ANSYS software. Based on this model, we simulated the output voltage and nonlinearity when piezoresistors locations change. The simulation results showed that as the stress of the longitudinal resistor (RL) was increased compared to the transverse resistor (RT), the nonlinear error of the pressure sensor would first decrease to about 0 and then increase. The theoretical calculation and mathematical fitting were given to this phenomenon. Based on this discovery, a method for optimizing the nonlinearity of high-pressure sensors while ensuring the maximum sensitivity was proposed. In the simulation, the output of the optimized model had a significant improvement over the original model, and the nonlinear error significantly decreased from 0.106% to 0.0000713%.

scholarly journals Study on the Stability of the Electrical Connection of High-Temperature Pressure Sensor Based on the Piezoresistive Effect of P-Type SiC

Micromachines ◽  
2021 ◽  
Vol 12 (2) ◽  
pp. 216
Author(s):  
Yongwei Li ◽  
Ting Liang ◽  
Cheng Lei ◽  
Qiang Li ◽  
Zhiqiang Li ◽  
...  
Keyword(s):  
High Temperature ◽  
Pressure Sensor ◽  
Pressure Sensors ◽  
Extreme Environment ◽  
Maximum Temperature ◽  
Piezoresistive Effect ◽  
Electrical Connection ◽  
Contact Stability ◽  
The Stability ◽  
P Type

In this study, a preparation method for the high-temperature pressure sensor based on the piezoresistive effect of p-type SiC is presented. The varistor with a positive trapezoidal shape was designed and etched innovatively to improve the contact stability between the metal and SiC varistor. Additionally, the excellent ohmic contact was formed by annealing at 950 °C between Ni/Al/Ni/Au and p-type SiC with a doping concentration of 1018cm−3. The aging sensor was tested for varistors in the air of 25 °C–600 °C. The resistance value of the varistors initially decreased and then increased with the increase of temperature and reached the minimum at ~450 °C. It could be calculated that the varistors at ~100 °C exhibited the maximum temperature coefficient of resistance (TCR) of ~−0.35%/°C. The above results indicated that the sensor had a stable electrical connection in the air environment of ≤600 °C. Finally, the encapsulated sensor was subjected to pressure/depressure tests at room temperature. The test results revealed that the sensor output sensitivity was approximately 1.09 mV/V/bar, which is better than other SiC pressure sensors. This study has a great significance for the test of mechanical parameters under the extreme environment of 600 °C.

Sign in / Sign up

Export Citation Format

Share Document