scholarly journals Computational analyses of tail fin configurations for a sounding rocket

2021 ◽  
Author(s):  
S. Sai Sankalp ◽  
Vansh Sharma ◽  
Abhyudaya Singh ◽  
Aneesh Surendra Salian ◽  
G. Srinivas
Keyword(s):  
Wind Tunnel ◽  
Three Dimensional ◽  
Design Criterion ◽  
Sounding Rocket ◽  
Computational Results ◽  
Aerodynamic Coefficients ◽  
Rolling Moment ◽  
Sounding Rockets ◽  
Computational Fluid Dynamics Cfd ◽  
Computational Analyses

AbstractMissiles and sounding rockets usually deviate from the trajectory due to unstable roll. Fins with cant angles are generally used to provide a rolling moment in sounding rockets and missiles to minimize the instability. Inducing a rolling moment also leads to an increase in the rocket motor’s power consumption due to the rise in drag, so inducing an optimal rolling moment with a minimal increase in drag is a crucial design criterion. It is crucial to maintain the similarity parameters while testing a scaled-down model in a wind tunnel. Therefore, computational fluid dynamics (CFD) is more efficient than extensive wind tunnel tests. In this paper, three-dimensional, incompressible simulations were performed on different models of sounding rockets using commercial CFD package fluent. The simulations were performed with the help of $$k-\epsilon $$ k - ϵ standard turbulence model. The results obtained were tabulated and graphically represented, and the trends of aerodynamic coefficients like $$C_{\text {d}}$$ C d and $$C_{\text {m}}$$ C m were analyzed. The purpose of this study is to analyze the dependency of aerodynamic coefficients on different fin configurations with emphasis on the cant angle. This study will be helpful to researchers designing a sounding rocket and help in maximizing apogee. The experimental and computational results show a favourable comparison. The results will show a particular configuration of fin having greater $$C_{\text {m}}/C_{\text {d}}$$ C m / C d which yields in a greater rolling moment and least amount of drag.

The simulation of single wraparound fin on a semi-cylindrical missile body

2020 ◽  
Vol 92 (3) ◽  
pp. 418-427 ◽  
Author(s):  
Nayhel Sharma ◽  
Rakesh Kumar
Keyword(s):  
Research Study ◽  
Cfd Simulation ◽  
Three Dimensional ◽  
Future Research ◽  
Aerodynamic Coefficients ◽  
Content Type ◽  
Computational Fluid Dynamics Cfd ◽  
Predicted Values ◽  
Characteristic Trend ◽  
Practical Implications

Purpose The purpose of this paper is to establish a freestream computational fluid dynamics (CFD) model of a three-dimensional non-spinning semi-cylindrical missile model with a single wrap around fin in Mach 2.70-3.00M range and 0° angle of attack, and ultimately establishing itself for future research study. Design/methodology/approach In this study, the behaviour of flow around the fin was investigated using a κ-ϵ turbulence model of second-order of discretization. This was done using a highly structured mesh. Additionally, an inviscid CFD simulation involving the same boundary conditions have also been carried out for comparison. Findings The obtained values of aerodynamic coefficients and pressure contours visualizations are compared against their experimental and computational counterparts. A typical missile aerodynamic characteristic trend can be seen in the current CFD. Practical implications The predicted values of the aerodynamic coefficients of this single fin model have also been compared to those of the full missile body comprising of four fins from the previous research studies, and a similar aerodynamic trend can be seen. Originality/value This study explores the possibility of the use of turbulence modelling in a single fin model of a missile and provides a basic computational model for further understanding the flow behaviour near the fin.

Aerodynamic Behavior of a Compound Wing Configuration in Ground Effect

2014 ◽  
Vol 66 (2) ◽  
Author(s):  
Saeed Jamei ◽  
Adi Maimun ◽  
Shuhaimi Mansor ◽  
Agoes Priyanto ◽  
Nor Azwadi ◽  
...  
Keyword(s):  
Three Dimensional ◽  
Ground Effect ◽  
Tip Vortex ◽  
Aerodynamic Coefficients ◽  
Ground Clearance ◽  
Reverse Taper ◽  
Current Experimental Data ◽  
Computational Fluid Dynamics Cfd ◽  
Ram Effect ◽  
Wing In Ground Effect

The aerodynamic coefficients of wing in ground effect can be affected with its design which can be the main parameter for efficiency of wing-in-ground effect craft. In this study, the aerodynamic coefficients of a compound wing were numerically determined in ground effect. The compound wing was divided into three parts with one rectangular wing in the middle and two reverse taper wings with an anhedral angle at the sides. An NACA6409 airfoil was employed as a section of wings. Three dimensional (3D) computational fluid dynamics (CFD) was applied as a numerical scheme. A realizable k-ε turbulent model was used for simulation the turbulent flow around the wing surfaces. For validation purpose, the numerical results of a compound wing with aspect ratio 1.25, at ground clearance of 0.15 and different angles of attack were compared with the current experimental data. Then, the aerodynamic coefficients of the compound wings were computed at various ground clearances and angle of attack of 4°. According to pressure and velocity distribution of air around wing surfaces, ground clearance had considerable effects on ram effect pressure and tip vortex of the compound wing, and aerodynamic coefficients of the compound wing had some improvements as compared with the rectangular wing.

3D Numerical Simulation of the Airflow in a Pneumatic Splicer

2011 ◽  
Vol 130-134 ◽  
pp. 2345-2348
Author(s):  
Xiao Xing ◽  
Guo Ming Ye
Keyword(s):  
Numerical Simulation ◽  
High Speed ◽  
Air Flow ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Swirling Flows ◽  
Computational Results ◽  
Cfd Model ◽  
3D Numerical Simulation ◽  
Computational Fluid Dynamics Cfd

To investigate the effect of air flow in an pneumatic splicer on splicing performance, a computational fluid dynamics (CFD) model has been developed to simulate the air flow characteristics in an splicing chamber. Three-dimensional numerical simulation is conducted and standard K-ε turbulence model is used. Velocity distributions in the chamber are presented and analyzed. The computational results show that the velocities in the chamber are transonic. The air flows in the chamber are two swirling flows with opposite directions. This work also shows that CFD technique can provide a better understanding of the behavior of the high speed air flow in the air splicing chamber.

Permissible three-dimensional testing in a two-dimensional adaptive wall wind tunnel

AIAA Journal ◽  
1997 ◽  
Vol 35 ◽  
pp. 749-750
Author(s):  
David Sumner ◽  
Ewart Brundrett
Keyword(s):  
Wind Tunnel ◽  
Three Dimensional ◽  
Two Dimensional

scholarly journals Galloping Stability and Wind Tunnel Test of Iced Quad Bundled Conductors considering Wake Effect

2020 ◽  
Vol 2020 ◽  
pp. 1-15
Author(s):  
Xiaohui Liu ◽  
Ming Zou ◽  
Chuan Wu ◽  
Mengqi Cai ◽  
Guangyun Min ◽  
...  
Keyword(s):  
Wind Tunnel ◽  
Transmission Lines ◽  
Degrees Of Freedom ◽  
Wind Tunnel Test ◽  
Aerodynamic Coefficients ◽  
Wake Effect ◽  
Aerodynamic Coefficient ◽  
Set Up ◽  
The Stability ◽  
Three Degrees Of Freedom

A new quad bundle conductor galloping model considering wake effect is proposed to solve the problem of different aerodynamic coefficients of each subconductor of iced quad bundle conductor. Based on the quasistatic theory, a new 3-DOF (three degrees of freedom) galloping model of iced quad bundle conductors is established, which can accurately reflect the energy transfer and galloping of quad bundle conductor in three directions. After a series of formula derivations, the conductor stability judgment formula is obtained. In the wind tunnel test, according to the actual engineering situation, different variables are set up to accurately simulate the galloping of iced quad bundle conductor under the wind, and the aerodynamic coefficient is obtained. Finally, according to the stability judgment formula of this paper, calculate the critical wind speed of conductor galloping through programming. The dates of wind tunnel test and calculation in this paper can be used in the antigalloping design of transmission lines.

Assessment of Unsteady Flows in Turbines

1992 ◽  
Vol 114 (1) ◽  
pp. 79-90 ◽  
Author(s):  
O. P. Sharma ◽  
G. F. Pickett ◽  
R. H. Ni
Keyword(s):  
Unsteady Flow ◽  
Three Dimensional ◽  
Flow Simulation ◽  
Experimental Investigations ◽  
Flow Parameters ◽  
Research Activities ◽  
Flow Features ◽  
Computational Fluid Dynamics Cfd ◽  
Turbine Design ◽  
The Impact

The impacts of unsteady flow research activities on flow simulation methods used in the turbine design process are assessed. Results from experimental investigations that identify the impact of periodic unsteadiness on the time-averaged flows in turbines and results from numerical simulations obtained by using three-dimensional unsteady Computational Fluid Dynamics (CFD) codes indicate that some of the unsteady flow features can be fairly accurately predicted. Flow parameters that can be modeled with existing steady CFD codes are distinguished from those that require unsteady codes.

The Effect of Bench Arrangements on the Natural Ventilation of a Multispan Greenhouse

2013 ◽  
Author(s):  
Sunita Kruger ◽  
Leon Pretorius
Keyword(s):  
Fluid Dynamics ◽  
Natural Ventilation ◽  
Three Dimensional ◽  
Two Dimensional ◽  
Low Velocity ◽  
Lower Velocity ◽  
Cfd Models ◽  
Temperature Distributions ◽  
Computational Fluid Dynamics Cfd ◽  
Plant Level

In this paper, the influence of various bench arrangements on the microclimate inside a two-span greenhouse is numerically investigated using three-dimensional Computational Fluid Dynamics (CFD) models. Longitudinal and peninsular arrangements are investigated for both leeward and windward opened roof ventilators. The velocity and temperature distributions at plant level (1m) were of particular interest. The research in this paper is an extension of two-dimensional work conducted previously [1]. Results indicate that bench layouts inside the greenhouse have a significant effect on the microclimate at plant level. It was found that vent opening direction (leeward or windward) influences the velocity and temperature distributions at plant level noticeably. Results also indicated that in general, the leeward facing greenhouses containing either type of bench arrangement exhibit a lower velocity distribution at plant level compared to windward facing greenhouses. The latter type of greenhouses has regions with relatively high velocities at plant level which could cause some concern. The scalar plots indicate that more stagnant areas of low velocity appear for the leeward facing greenhouses. The windward facing greenhouses also display more heterogeneity at plant level as far as temperature is concerned.

Mechanism and Flow Control on the Mismatching of Impeller and Vaned Diffuser Caused by Inlet Prewhirl for Centrifugal Compressors

2016 ◽  
Author(s):  
Qiangqiang Huang ◽  
Xinqian Zheng ◽  
Aolin Wang
Keyword(s):  
Flow Control ◽  
Control Method ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Vaned Diffuser ◽  
Inlet Distortion ◽  
Computational Fluid Dynamics Cfd ◽  
Stagger Angle ◽  
Good Agreement ◽  
Matching Relation

Air often flows into compressors with inlet prewhirl, because it will obtain a circumferential component of velocity via inlet distortion or swirl generators such as inlet guide vanes. A lot of research has shown that inlet prewhirl does influence the characteristics of components, but the change of the matching relation between the components caused by inlet prewhirl is still unclear. This paper investigates the influence of inlet prewhirl on the matching of the impeller and the diffuser and proposes a flow control method to cure mismatching. The approach combines steady three-dimensional Reynolds-averaged Navier-Stokes (RANS) simulations with theoretical analysis and modeling. The result shows that a compressor whose impeller and diffuser match well at zero prewhirl will go to mismatching at non-zero prewhirl. The diffuser throat gets too large to match the impeller at positive prewhirl and gets too small for matching at negative prewhirl. The choking mass flow of the impeller is more sensitive to inlet prewhirl than that of the diffuser, which is the main reason for the mismatching. To cure the mismatching via adjusting the diffuser vanes stagger angle, a one-dimensional method based on incidence matching has been proposed to yield a control schedule for adjusting the diffuser. The optimal stagger angle predicted by analytical method has good agreement with that predicted by computational fluid dynamics (CFD). The compressor is able to operate efficiently in a much broader flow range with the control schedule. The flow range, where the efficiency is above 80%, of the datum compressor and the compressor only employing inlet prewhirl and no control are just 25.3% and 31.8%, respectively. For the compressor following the control schedule, the flow range is improved up to 46.5%. This paper also provides the perspective of components matching to think about inlet distortion.

Sign in / Sign up

Export Citation Format

Share Document