Effect of different supplementary cementitious materials on mechanical properties of high performance concrete

1995 ◽  
Vol 25 (1) ◽  
pp. 209-220 ◽  
Author(s):  
R.P. Khatri ◽  
V. Sirivivatnanon ◽  
W. Gross
Keyword(s):  
Mechanical Properties ◽  
High Performance ◽  
High Performance Concrete ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials

The Effect of Homogenization Procedure on Mechanical Properties of High-Performance Concrete with Partial Replacement of Cement by Supplementary Cementitious Materials

2019 ◽  
Vol 292 ◽  
pp. 102-107 ◽  
Author(s):  
Josef Fládr ◽  
Petr Bílý ◽  
Karel Šeps ◽  
Roman Chylík ◽  
Vladimír Hrbek
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Water Content ◽  
High Performance ◽  
High Performance Concrete ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Partial Replacement ◽  
Depth Of Penetration ◽  
Cement Additive

High-performance concrete is a very specific type of concrete. Its production is sensitive to both the quality of compounds used and the order of addition of particular compounds during the homogenization process. The mechanical properties were observed for four dosing procedures of each of the three tested concrete mixtures. The four dosing procedures were identical for the three mixes. The three mixes varied only in the type of supplementary cementitious material used and in water content. The water content difference was caused by variable k-value of particular additives. The water-to-binder ratio was kept constant for all the concretes. The additives used were metakaolin, fly ash and microsilica. The comparison of particular dosing procedures was carried out on the values of basic mechanical properties of concrete. The paper compares compressive strength and depth of penetration of water under pressure. Besides the comparsion of macro-mechanical properties, the effect of microsilica and fly ash additives on micro-mechanical properties was observed with the use of scanning electron microscopy (SEM) and nanoindentation data analysis. Nanoindentation was used to determine the thickness and strength of interfacial transition zone (ITZ) for different sequence of addition of cement, additive and aggregate. The thickness obtained by nanoindentation was further investigated by SEM EDS line scanning.

scholarly journals Compressive and Flexural Strength Property Enhancement for Fibre Reinforced Standard Concrete (FRSC), High Strength Concrete (FRHSC) and High Performance Concrete (FRHPC) using Foundry Sand (FS) and Crushed Concrete Waste (CCW)

2021 ◽  
Vol 2 (2) ◽  
Author(s):  
Pruthviraj S R ◽  
Ravi Kumar C M ◽  
Yajnodbhavi H M ◽  
Maruthi T ◽  
Raghavendra S
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
High Performance ◽  
High Performance Concrete ◽  
Research Work ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Specific Test ◽  
Foundry Sand ◽  
Crushed Concrete

Now days, many research works are carried for all grades of concrete to make the concrete most economical and durable there by adding the supplementary cementitious materials and alternative replacement aggregates. In this research work deals with the experimental investigation of mechanical properties of the M30, M50 and M80 grade concrete by replacing the fine and coarse aggregate by foundry sand and crushed concrete waste respectively. Mix design procedures were followed as per IRC44:2017 guidelines and recommendation. Proper dosage of super plasticizer (SP) was maintained in the concrete to make it better performed. In this present investigation, a Poly Propylene fibre (PPF) of 0.3% by weight of the cement is used. Mechanical properties such as Compressive strength and Flexural Strength were determined by preparing the respective mould sizes for specific test and are cured for 7, 14 and 28 days and result obtained for respective days were tabulated and discussed.  

Influence of Washing of Crushed Aggregate on Mechanical Properties of High-Performance Concrete Containing Supplementary Cementitious Materials

2020 ◽  
Vol 309 ◽  
pp. 26-30 ◽  
Author(s):  
Josef Fládr ◽  
Petr Bílý ◽  
Tomáš Trtík ◽  
Roman Chylík ◽  
Vladimír Hrbek
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
High Performance ◽  
High Performance Concrete ◽  
Cementitious Materials ◽  
Positive Influence ◽  
Supplementary Cementitious Materials ◽  
Basic Material ◽  
Depth Of Penetration ◽  
Crushed Aggregate

The paper compares macromechanical and micromechanical properties of high-performance concrete containing supplementary cementitious materials and basalt aggregate. The aggregate was either a common unprocessed crushed basalt aggregate or crushed basalt aggregate the coarse fractions (4/8 and 8/16 mm) of which were washed by water and dried before use. The observed macro-mechanical properties were compressive strength, tensile strength, elastic modulus and depth of penetration of water under pressure; the paper is focused on the first observed property, which is the basic material characteristic. On the microscale, the thickness of the interfacial transition zone (ITZ) was determined by nanoindentation. The positive influence of supplementary cementitious materials and aggregate washing on compressive strength was confirmed and the correlation between macromechanical and micromechanical characteristics was proved.

scholarly journals Experimental Investigation and Prediction of Compressive Strength of Ultra-High Performance Concrete Containing Supplementary Cementitious Materials

2017 ◽  
Vol 2017 ◽  
pp. 1-8 ◽  
Author(s):  
Jisong Zhang ◽  
Yinghua Zhao ◽  
Haijiang Li
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
High Performance ◽  
High Performance Concrete ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Ann Model ◽  
Ultra High Performance Concrete ◽  
Superior Mechanical Properties ◽  
Normal Strength

Ultra-high performance concrete (UHPC) has superior mechanical properties and durability to normal strength concrete. However, the high amount of cement, high environmental impact, and initial cost are regarded as disadvantages, restricting its wider application. Incorporation of supplementary cementitious materials (SCMs) in UHPC is an effective way to reduce the amount of cement needed while contributing to the sustainability and cost. This paper investigates the mechanical properties and microstructure of UHPC containing fly ash (FA) and silica fume (SF) with the aim of contributing to this issue. The results indicate that, on the basis of 30% FA replacement, the incorporation of 10% and 20% SF showed equivalent or higher mechanical properties compared to the reference samples. The microstructure and pore volume of the UHPCs were also examined. Furthermore, to minimise the experimental workload of future studies, a prediction model is developed to predict the compressive strength of the UHPC using artificial neural networks (ANNs). The results indicate that the developed ANN model has high accuracy and can be used for the prediction of the compressive strength of UHPC with these SCMs.

scholarly journals Effect of Graphene Oxide Nanosheets on Physical Properties of Ultra-High-Performance Concrete with High Volume Supplementary Cementitious Materials

Materials ◽  
2020 ◽  
Vol 13 (8) ◽  
pp. 1929 ◽  
Author(s):  
Yu-You Wu ◽  
Jing Zhang ◽  
Changjiang Liu ◽  
Zhoulian Zheng ◽  
Paul Lambert
Keyword(s):  
Graphene Oxide ◽  
Physical Properties ◽  
High Performance ◽  
High Performance Concrete ◽  
High Volume ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Ultra High Performance Concrete ◽  
Steam Curing ◽  
Slump Flow

Nanomaterials have been increasingly employed for improving the mechanical properties and durability of ultra-high-performance concrete (UHPC) with high volume supplementary cementitious materials (SCMs). Recently, graphene oxide (GO) nanosheets have appeared as one of the most promising nanomaterials for enhancing the properties of cementitious composites. To date, a majority of studies have concentrated on cement pastes and mortars with fewer investigations on normal concrete, ultra-high strength concrete, and ultra-high-performance cement-based composites with a high volume of cement content. The studies of UHPC with high volume SCMs have not yet been widely investigated. This paper presents an experimental investigation into the mini slump flow and physical properties of such a UHPC containing GO nanosheets at additions from 0.00 to 0.05% by weight of cement and a water–cement ratio of 0.16. The study demonstrates that the mini slump flow gradually decreases with increasing GO nanosheet content. The results also confirm that the optimal content of GO nanosheets under standard curing and under steam curing is 0.02% and 0.04%, respectively, and the corresponding compressive and flexural strengths are significantly improved, establishing a fundamental step toward developing a cost-effective and environmentally friendly UHPC for more sustainable infrastructure.

Fresh Properties of Mortar made with Pozzolanic Cement and Water Reducers

2012 ◽  
Vol 1488 ◽  
Author(s):  
María E. Sosa ◽  
Yury A. Villagrán-Zaccardi ◽  
Claudio J. Zega ◽  
P.Peralta Juan
Keyword(s):  
High Performance ◽  
High Performance Concrete ◽  
Practical Implication ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Surface Finishing ◽  
Main Role ◽  
Natural Pozzolans ◽  
Different Types ◽  
Pozzolanic Cement

ABSTRACTNatural pozzolans are supplementary cementitious materials (SCMs) that may be used to improve the properties of mortar and concrete, through the formation of additional hydration products by pozzolanic action. Water reducers (WR) play a main role in high performance concrete in terms of durability, strength and surface finishing. A first optimization of constituent proportions in paste and/or mortar is convenient to assess the compatibility between the WR and the cementitious materials. The compatibility between cement and WR may be affected by SCMs, as they can also interact with the molecules of the admixture. However, the practical implication may be variable. This paper deals with the influence of different types and dosages of WRs in mortars made with pozzolanic Portland cement. Both medium and high ranges WRs have been used. Mortar fluidity has been tested by the spread and the slump tests. Results show different fluidizing capacities of WRs, among which polycarboxylate-based WR was the most compatible with the pozzolanic cement.

Sign in / Sign up

Export Citation Format

Share Document