A DESK-TOP PERSONAL COMPUTER FOR FINITE ELEMENT POST-PROCESSING

1983 ◽  
pp. 689-695
Author(s):  
JAMES R. STAFFORD
Keyword(s):  
Finite Element ◽  
Personal Computer ◽  
Post Processing

scholarly journals Folding photopolymerized origami sheets by post-curing

2021 ◽  
Vol 3 (1) ◽  
Author(s):  
Xiaodong He ◽  
Christopher-Denny Matte ◽  
Tsz-Ho Kwok
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Maximum Principal Stress ◽  
Second Step ◽  
Post Processing ◽  
Element Analysis ◽  
Digital Light Processing ◽  
Processing Step ◽  
Lower Maximum

AbstractThe paper presents a novel manufacturing approach to fabricate origami based on 3D printing utilizing digital light processing. Specifically, we propose to leave part of the model uncured during the printing step, and then cure it in the post-processing step to set the shape in a folded configuration. While the cured regions in the first step try to regain their unfolded shape, the regions cured in the second step attempt to keep their folded shape. As a result, the final shape is obtained when both regions’ stresses reach equilibrium. Finite element analysis is performed in ANSYS to obtain the stress distribution on common hinge designs, demonstrating that the square-hinge has a lower maximum principal stress than elliptical and triangle hinges. Based on the square-hinge and rectangular cavity, two variables—the hinge width and the cavity height—are selected as principal variables to construct an empirical model with the final folding angle. In the end, experimental verification shows that the developed method is valid and reliable to realize the proposed deformation and 3D development of 2D hinges.

Advancement in the Application of Finite Element Analysis to the Optimization of Composite Yacht Structures

2011 ◽  
Author(s):  
David Fornaro
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Composite Structures ◽  
State Of The Art ◽  
Load Case ◽  
Post Processing ◽  
Principal Stresses ◽  
Element Analysis ◽  
Current State ◽  
Case Development

Finite Element Analysis (FEA) is mature technology that has been in use for several decades as a tool to optimize structures for a wide variety of applications. Its application to composite structures is not new, however the technology for modeling and analyzing the behavior of composite structures continues to evolve on several fronts. This paper provides a review of the current state-of-the-art with regard to composites FEA, with a particular emphasis on applications to yacht structures. Topics covered are divided into three categories: Pre-processing; Postprocessing; and Non-linear Solutions. Pre-processing topics include meshing, ply properties, laminate definitions, element orientations, global ply tracking and load case development. Post-processing topics include principal stresses, failure indices and strength ratios. Nonlinear solution topics include progressive ply failure. Examples are included to highlight the application of advanced finite element analysis methodologies to the optimization of composite yacht structures.

scholarly journals A New Design Procedure for Rotor Laminations of Synchronous Reluctance Machines with Fluid Shaped Barriers

Electronics ◽  
2022 ◽  
Vol 11 (1) ◽  
pp. 134
Author(s):  
Federica Uberti ◽  
Lucia Frosini ◽  
Loránd Szabó
Keyword(s):  
Finite Element ◽  
Design Procedure ◽  
Optimization Procedure ◽  
Torque Ripple ◽  
Stator Winding ◽  
Post Processing ◽  
Processing Stage ◽  
Synchronous Reluctance Machine ◽  
Design And Optimization ◽  
Reluctance Machine

A new procedure for the design and optimization of the rotor laminations of a synchronous reluctance machine is presented in this paper. The configuration of the laminations is symmetrical and contains fluid-shaped barriers. The parametrization principle is used, which executes variations in the lamination geometry by changing the position, thickness and shape of the flux barriers. Hence, the optimization procedure analyzes the various configurations through finite element simulations, by means of the communication between MATLAB and Flux 2D. In the post processing stage, the best geometry which optimizes mean torque, torque ripple, efficiency and power factor is selected. Once the best rotor configuration is defined, further investigations allow improving its performance by modifying the current angle, the stator winding and the thickness of the radial ribs.

Linear Static, Real-Time Finite Element Computations Based on Element Masks

2011 ◽  
Author(s):  
Holger Graf ◽  
Andre´ Stork
Keyword(s):  
Finite Element ◽  
Stress Field ◽  
Boundary Conditions ◽  
Real Time ◽  
Stiffness Matrix ◽  
New Method ◽  
Stress Distributions ◽  
Post Processing ◽  
Time Performance ◽  
Computational Overhead

This paper presents a new method for the manipulation of a given CAE domain in view of VR based explorations that enables engineers to interactively inspect and analyze a linear static domain. The interactions can ideally be performed in real-time in order to provide an intuitive impression of the changes to the underlying volumetric domain. We take the approach of element masking, i.e. the blending out of computations resulting from computational overhead for inner nodes, based on the inversion of the stiffness matrix. This allows us to optimize the re-simulation loop and to achieve real-time performance for strain and stress distributions with immediate visualization feedback caused by interactively changing boundary conditions. The novelty of the presented approach is a direct coupling of view dependent simulations and its close linkage to post-processing tasks. This allows engineers to also inspect the changes of the stress field inside of the volume during, e.g. cross sectioning.

Sign in / Sign up

Export Citation Format

Share Document