Estimating milk yield for individual cows using measurements of total milk flow

2021 ◽  
Vol 190 ◽  
pp. 106473
Author(s):  
P.R. Shorten
Keyword(s):  
2011 ◽  
Vol 28 (2) ◽  
pp. 139-146 ◽  
Author(s):  
Peter Strapák ◽  
Peter Antalík ◽  
Iveta Szencziová

Milkability evaluation of Holstein dairy cows by LactocorderThe aim of this work was to evaluate chosen milk flow characteristics of Holstein dairy cows, using mobile electronic milk flow meters - Lactocorders. A total of 181 Holstein dairy cows were evaluated and divided according to parity, lactation stage and bimodality in order to carry out a detailed comparison of measured milkability traits. The average total milk yield was 11.98±3.41 kg per milking with an average milk flow rate of 2.52±0.75 kg min-1 and a maximum milk flow rate of 3.94±1.30 kg min-1. The total milk yield showed positive correlations with the average milk flow rate (r = 0.48; P<0.001) and also with the maximum milk flow rate (r = 0.32; P<0.001). More than 47% of milk flow curves were classified as bimodal. Bimodality was positively correlated with the duration of the incline phase (r = 0.73; P<0.001) and negatively correlated with the quantity of milk obtained during the first minute of milking (r = -0.34; P<0.001). In relation to the lactation stage - the highest average milk flow rate was reached by Holstein dairy cows at the beginning of the lactation (up to 100 days in milk), and in relation to parity - the highest milk flow rates were measured in second-lactation dairy cows.


1995 ◽  
Vol 62 (4) ◽  
pp. 559-566 ◽  
Author(s):  
Hans-Ulrich Pfeilsticker ◽  
Rupert M. Bruckmaier ◽  
Jürg W. Blum

SUMMARYExperiments were designed to test the hypothesis that milk ejection rate decreases during milking, thereby causing insufficient refill of the cistern and decreasing milk flow rate towards the end of milking. In a first series of experiments machine milking of the left front quarters of 11 cows was interrupted for 2 min after removal of 25, 50 or 75% of expected total milk yield, while milking was continued in the other three quarters. Milk flow was recorded during machine-on times. Intramammary pressure (IMP) was recorded during premilking teat stimulation and during interruption of milking. IMP during interruption of milking decreased with decreasing amounts of milk remaining in the udder. The IMP did not change during these interruptions when they occurred after 25 and 50% of expected total milk yield was removed. Thus, the ejection rate could keep up with the milk flow or removal rate. However, IMP increased during interruption of milking following removal of 75% of total yield, although significantly so only in cows with a high milk flow rate. Obviously, more milk was removed than was transported to the cisternal cavity. It is likely that a reduced ejection rate caused the decreased milk flow rate. In a second series of experiments the pulsation ratio of the milking machine was changed from the usual 70:30 to 50:50 with the aim of reducing the milk flow rate and thus adapting to the ejection rate at the end of milking. The changed pulsation ratio caused a reduced peak flow rate and a prolonged high milk flow period, whereas the main flow rate did not change significantly.


2017 ◽  
Vol 48 (1) ◽  
pp. 53-55
Author(s):  
Francesco Maria Tangorra ◽  
Stefania Leonardi ◽  
Valerio Bronzo ◽  
Nicola Rota ◽  
Paolo Moroni

The objective of the present study was to investigate the effect of pre-milking mechanical teat stimulation on milk yield and milking performance of dairy buffaloes in early lactation. For this purpose, twenty-two healthy Italian Mediterranean buffaloes in their first to third lactation and in early lactation (<120 days in milk) were subjected to two treatments of teat stimulation: i) washing of the teats with water for about 5 s and attaching of the milking unit within 60 s, without any pre-milking massage (farm milking routine); ii) fast pulsation (FP), achieved by increasing pulsation rate to 120 pulsations per min during the first 60 s after application of teat cups. Each treatment lasted for 10 days and the following parameters were measured: milk yield (kg/milking), milk yield at 2 min after unit attachment (kg), time between milking unit attachment and its automatic removal (min), peak milk flow rate (kg/min), and milking time to reach peak flow rate (min). The average milk flow rate (kg/min) was calculated by dividing milk yield by the actual milking time. Milk yield was not affected by mechanical pre-stimulation and during the first 2 min of milking 20.2% and 19.6% of total milk yield were milked respectively when treatments 1 and 2 were applied. The time elapsed from attachment of the milking cluster until its automatic removal was less than 8 min both for buffaloes subjected to FP, and for buffaloes subjected just to washing of the teats before attaching the milking unit. FP stimulation did not show an enhancing effect on peak and average milk flow rates and on milking time to reach peak flow rate.


2012 ◽  
Vol 48 (No. 10) ◽  
pp. 275-282 ◽  
Author(s):  
V. Tancin ◽  
A.H. Ipema ◽  
D. Peskovicova ◽  
P.H. Hogeverf ◽  
J. Macuhova

The objectives of our study were to describe the variation of quarter milk flow parameters and to determine the factors that affect these parameters the most. Additionally, repeatabilities (r<sub>2</sub>) of the quarter milk flow traits (duration of milk flow, time to reach peak flow, peak flow rate, and duration of milk flow in single phases &ndash; increase, plateau, decline and blind phase) were calculated. Repeatability of total milk yield and milk yield in single phases was calculated, too. The data from 39 Holstein cows, in their first to third lactation and free of clinical mastitis, were used for statistical analysis. A total of 1 656 curves of quarter milk flows were recorded during six consecutive days. At the last evening and morning milking samples of milk from each quarter were collected for determination of somatic cell count (SCC). Peak flow rate, quarter position, time of milking (morning and evening) and SCC significantly affected most of the measured traits. The highest r2 were for total milk yield and yield of plateau phase 0.53 and 0.50, resp. The lowest r2 were calculated for the duration of increase phase, and milk yield of the increase and blind phase 0.26, 0.12 and 0.21, resp. Peak flow rate, SCC, time of milking and front-rear position influenced the values of r2 of traits to various extent.


10.5219/1071 ◽  
2019 ◽  
Vol 13 (1) ◽  
pp. 275-279
Author(s):  
Lucia Mačuhová ◽  
Vladimír Tančin ◽  
Juliana Mačuhová ◽  
Michal Uhrinčať ◽  
Milan Margetin

Improved Valachian (IV x LC; n = 41) and Tsigai (TS x LC; n = 44) crossbred ewes with Lacaune were used to study the effects of three weaning systems on milk production. Prior to parturition, ewes were assigned to one of the following three treatments for the first 53 day of lactation: 1) ewes weaned from their lambs at 24 h postpartum and afterwards machine milked twice daily (MTD), 2) ewes, beginning 24 h postpartum, kept during the daytime with their lambs and allowed them to suckle for 12 h, nights separated from their lambs for 12 h and machine milked once daily in the morning (MIX), and 3) ewes exclusively suckled by their lambs (ES). After the treatment period, lambs were weaned from MIX and ES ewes, and all three groups were machine milked twice daily. Furthermore, ewes were evaluated according to number of live-born and weaned lambs (with one (n = 35) or with two lambs (n = 50)). The measurements of milk yield and milk flow were performed on 110 ±5 day of lactation by the equipment for graduated electronic recording of the milk level in a jar in one-second intervals. No significant differences were observed in the measured values (total milk yield, machine milk yield, latency time, milking time, machine stripping, milk flow rate, and machine milk yield in 30 and 60 s) among weaning treatments and between ewes with one or two lambs and evaluated breeds too. The highest occurrence of one peak milk flow (milk flow without milk ejection) was found out in MTD ewes (50%) compared to MIX (19%) and ES (17%). In conclusion, the different systems of weaning did not influence the milk yield and milk flow parameters in the mid-lactation.


2008 ◽  
Vol 53 (No. 12) ◽  
pp. 528-536 ◽  
Author(s):  
L. Mačuhová ◽  
M. Uhrinčať ◽  
J. Mačuhová ◽  
M. Margetín ◽  
V. Tančin

The aim of this study was to evaluate the milkability of two purebred breeds Tsigai (TS, <i>n</i> = 14) and Improved Valachian (IV, <i>n</i> = 15), their crosses with Lacaune 50% TS × 50% LC (<i>n</i> = 13), 50% IV × 50% LC (<i>n</i> = 9) and purebred Lacaune (LC, <i>n</i> = 19). The measurements of the milk flow were performed on day 90 ± 10 of lactation during evening machine milking. The recording of milk flow was carried out by the equipment for graduated electronic recording of milk level in a jar in one-second intervals. The milk flow curves were classified into four types: 1 peak (1P), 2 peaks (2P), plateau I (maximal milk flow over 0.4 l/min (PLI)), plateau II (maximal milk flow less than 0.4 l/min (PLII)). The last two types refer to ewes with steady milk flow during milking. Udder morphology traits were measured (cisternal depth, teat angle) and subjectively assessed by the use of linear scores (cistern depth, teat position). The average total milk yield was 0.335 ± 0.043, 0.392 ± 0.042, 0.407 ± 0.042 l in purebred TS, IV, LC resp. and 0.397 ± 0.046, 0.434 ± 0.056 l in crosses TS × LC and IV × LC, resp. The frequency of occurrence of different types of milk flow /1P:2P:PLI:PLII/ was 27, 47, 22, 4%, resp. The highest milk yield was observed in ewes with PLI (0.481 ± 0.045 l), followed by 2P (0.401 ± 0.029 l) and 1P (0.293 ± 0.036 l) type of milk flow curve (<i>P</i> = 0.0112). An opposite effect was observed in the percentage of machine stripping yield where 1P had 41.94 ± 3.83%, 2P 21.29 ± 3.04% and PLI 15.90 ± 4.70% (<i>P</i> < 0.0001). LC and TS × LC, IV × LC had the more horizontal teat position than TS and IV. It can be supposed that at least during around 69% milkings the sheep released oxytocin in response to machine milking and that TS, IV and their crosses with LC also have a suitable potential for machine milking.


2003 ◽  
Vol 51 (2) ◽  
pp. 191-198
Author(s):  
P. Mijić ◽  
I. Knežević ◽  
M. Baban ◽  
M. Domaćinović ◽  
D. Rimac

Recently secondary cattle selection traits have been given more attention in developed cattle breeding countries in establishing a selection index. In this way, milking traits have acquired a prominent place. This paper aimed to determine coefficients of correlation and regression between a number of milking traits, that could be helpful in establishing a selection index for breeding bulls and their dams. A further goal was to determine the distribution of milking parameters. The data of 303 Holstein Friesian and 235 Simmental cows were analysed.  The results showed that in both cow breeds correlations existed between milk yield and average milk flow (0.39 and 0.49), as well as between milk yield and milking time (0.53 and 0.35). Negative correlations were found between average milk flow and milking time (-0.49 and -0.56). For the Holstein Friesian breed, 67.0% of the cows had a total milk flow in the range of 1.61 to 3.60 kg/min, whereas in the Simmental breed 72.2% of the cows had a total milk flow of 2.40 kg/min.  The milk flow rate can be indirectly affected by selecting cows with higher milk production. The definition of an optimal milk flow rate and the determination of breeding goals for milking traits will lead to faster progress in milking trait improvement and an easier choice of quality breeding bulls and dams.


1996 ◽  
Vol 63 (2) ◽  
pp. 191-200 ◽  
Author(s):  
Rupert M. Bruckmaier ◽  
Hans-Ulrich Pfeilsticker ◽  
Jürg W. Blum

SummaryFor six successive milkings, six dairy cows were relocated immediately before milking to an unfamiliar operating theatre, a procedure previously shown to inhibit oxytocin release and milk ejection. Two control milkings were performed in familiar surroundings. After milk flow had ceased, two i.v. injections of 1 i.u. oxytocin were given to remove the remaining milk. Milk flow was recorded continuously and blood samples were taken every minute during milking and 10 min after milking. During the first milking in unfamiliar surroundings, no oxytocin was released. Thereby, only 13% of the total milk yield, the cisternal milk, was available and the alveolar milk fraction could only be removed after injection of oxytocin. During subsequent relocations oxytocin release steadily increased toward the control level, although the timing of oxytocin release remained delayed as compared with controls. However, the milk fraction available before oxytocin injection increased with increasing number of removals, following an asymptotic approach to control levels. The concentrations of β-endorphin, cortisol (and perhaps also of prolactin) gradually declined with the number of times the animal was moved to unfamiliar surroundings, i.e. hormone concentrations gradually adjusted to control level. During milking, concentrations of prolactin and cortisol increased, while β-endorphin concentrations decreased (except for the first relocation). We conclude that milking-related oxytocin release and therefore milk ejection adapted gradually to repeated relocations to unfamiliar surroundings. This adaptation was inversely related to β-endorphin concentrations, so it is possible that oxytocin release was suppressed by high circulating β-endorphin concentrations.


10.5219/1411 ◽  
2020 ◽  
Vol 14 ◽  
pp. 1035-1041
Author(s):  
Lucia Mačuhová ◽  
Vladimí­r Tančin ◽  
Juliana Mačuhová ◽  
Michal Uhrinčať ◽  
Marta Oravcová ◽  
...  

The trial aimed to study the effect of somatic cell count, breed, milk flow type, and parity on the milkability and milk composition of ewes. The flock consists of purebred Lacaune ewes (LC; n = 29) and crossbreds ewes of Improved Valachian (IV x LC; n = 35) and Tsigai (TS x LC; n = 37) with LC (with a genetic portion of Lacaune 25 and 50%). Ewes were assigned according to somatic cell count (SCC) to one of the following three groups: SCC ≤300,000 cells per mL (SCC Group 300,000), SCC between 300,000 and 1000,000 cells per mL (SCC Group 300,000 – 1000,000), SCC ≥1000,000 cells per mL (SCC Group 1000,000). 56% of evaluated ewes had less than 300,000 cells per mL and 29% more than 1000,000 cells per mL in milk. No significant differences were observed between different groups of SCC in total, machine milk yield, and the proportion of milk yield in 30 s and 60 s. The significant differences were observed between SCC Group 300,000 and SCC Group 300,000 – 1000,000 in the proportion of machine stripping from total milk yield (41 ±2 vs. 57 ±4%). Milk flow type had a significant effect on all evaluated milkability parameters but not on milk composition. Ewes on fourth parity had the highest proportion of machine stripping from total milk yield then ewes on third, fifth, and sixth and higher (60% vs. 47, 45, 46%; resp.). Effect of SCC Group on milk composition manifested only in solids not fat. The significant differences were observed between SCC Group 1000,000 to SCC Group 300,000 and SCC Group 300,000 – 1000,000 (10.75 ±0.08% vs. 11.05 ±0.06 and 11.15 ±0.11%, p ≤0.0004).


2013 ◽  
Vol 53 (6) ◽  
pp. 573 ◽  
Author(s):  
J. P. Edwards ◽  
J. G. Jago ◽  
N. Lopez-Villalobos

It was hypothesised that large rotary dairies (>60 clusters) are not more operator efficient than medium-sized rotaries (40–60 clusters). This was tested by collecting and analysing milking data, during peak and late lactation, from block calving herds milked in rotary dairies fitted with electronic milk meters. Data were collected from a total of 61 unique farms around New Zealand, with rotary dairies ranging in size from 28 to 80 clusters, for two 5-day periods during spring (September–November 2010; 47 farms; average milk yield 23.1 kg/day) and autumn (February–April 2011; 60 farms; average milk yield 16.4 kg/day). A telephone survey was conducted to collect basic farm details: size, land area, the number of herds managed (including hospital herds), number of operators in the dairy and total labour input. A site visit was conducted to collect data such as the number of bails/stalls over the entrance and exit of the platform. The herd management software on each farm was programmed to record similar fields for each of the six machine manufacturers represented. Variables recorded included cow, date, identification time, bail number, milk yield, milking duration, and average milk flow rate. Calculations were performed to determine the number of cows milked and milk harvested per hour as well as the operator efficiency values for these measures and an estimate of cluster utilisation. Mixed models were used to determine the relationship between the dependent variables, cows milked per hour, milk harvested per hour, cows milked per operator per hour, milk harvested per operator per hour, and cluster utilisation, and the independent variables collected. Cows milked and milk harvested per hour increased linearly with rotary size, during both spring and autumn and there was a quadratic relationship between operator efficiency measures and rotary size, which peaked at ~60 clusters. Cluster utilisation, the amount of time clusters were harvesting milk out of the plant running time, was estimated at 46 ± 6%. Larger rotary dairies on average achieved greater throughput; however, they were not more operator efficient than medium-sized rotaries. Thus, large rotary dairies are best suited to farms where the additional throughput is required.


Sign in / Sign up

Export Citation Format

Share Document