scholarly journals Effect of Casting Position on Mechanical Performance of Ultra-High Performance Concrete

Materials ◽  
2022 ◽  
Vol 15 (2) ◽  
pp. 404
Author(s):  
Sujing Zhao ◽  
Yiheng Bo
Keyword(s):  
Flexural Strength ◽  
High Performance ◽  
Mechanical Performance ◽  
High Performance Concrete ◽  
Fiber Type ◽  
Peak Load ◽  
Load Ratio ◽  
Fiber Types ◽  
Ultra High Performance Concrete ◽  
Fracture Properties

The mechanical performance of ultra-high performance concrete (UHPC) is a function of fiber distribution and orientation, which are affected by the processing of the fresh material. In this study, the influences of two casting positions (mid-cast and end-cast) on strength and fracture properties of UHPCs with different fiber types and fiber contents were investigated. The results show that mid-cast specimens have higher flexural strength and fracture properties than end-cast specimens, while the compressive strength is almost unaffected by casting position. Compared to specimens with straight fibers, the flexural strength of specimens with hooked-end fibers is more likely to be affected by casting position. The residual load-to-peak load ratio is independent of casting position but affected by fiber type and fiber content.

scholarly journals Determination of Axial Capacity for Enhanced Normal and Ultra - High Performance Concrete Columns

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Sarmad Shafeeq Abdulqader ◽  
Asmaa Ali Ahmed ◽  
Nawfal Shihab Ahmed
Keyword(s):  
High Performance ◽  
High Performance Concrete ◽  
Peak Load ◽  
Concrete Cover ◽  
Ultra High Performance Concrete ◽  
Concrete Technology ◽  
Compression Load ◽  
Axial Capacity ◽  
Load Carrying ◽  
Normal Strength

Abstract Concrete Technology has been developing for more than a century. One of the most exceptional achievements in concrete technology is the evolving of Ultra-High Performance Concrete (UHPC) which has been a research focus in a wide applications diversity. In this paper, an experimental work has been carried out for investigating the transverse and longitudinal reinforcements’ variation influence on the axial capacity of UHPC columns. Eight columns (five UHPC columns and three Normal Strength Concrete (NSC) columns) have been poured and tested under a concentric axial compression load till a failure is reached. Then, the results are reported herein. The experimental results show that UHPC columns failed in a controlled manner and no concrete chips or a concrete cover spalling are observed. Also, the longitudinal reinforcements have not buckled away beyond the peak load because of the presence of the reinforcing steel fibers in UHPC. Correspondingly, the steel ties spacing proportionally affects the load carrying capacity of columns as presented hereinafter.

scholarly journals Flexural Strength Evaluation of Reinforced Concrete Members with Ultra High Performance Concrete

2016 ◽  
Vol 2016 ◽  
pp. 1-10 ◽  
Author(s):  
Baek-Il Bae ◽  
Hyun-Ki Choi ◽  
Chang-Sik Choi
Keyword(s):  
Flexural Strength ◽  
High Performance ◽  
Strain Softening ◽  
Steel Fiber ◽  
High Performance Concrete ◽  
High Strength ◽  
Tension Stress ◽  
Compression Stress ◽  
Ultra High Performance Concrete ◽  
Stress Block

Flexural strength evaluation models for steel fiber reinforced ultra high strength concrete were suggested and evaluated with test results. Suggested flexural strength models were composed of compression stress blocks and tension stress blocks. Rectangular stress block, triangular stress block, and real distribution shape of stress were used on compression side. Under tension, rectangular stress block distributed to whole area of tension side and partial area of tension side was used. The last model for tension side is realistic stress distribution. All these models were verified with test result which was carried out in this study. Test was conducted by four-point loading with 2,000 kN actuator for slender beam specimen. Additional verifications were carried out with previous researches on flexural strength of steel fiber reinforced concrete or ultra high strength concrete. Total of 21 test specimens were evaluated. As a result of comparison for flexural strength of section, neutral axis depth at ultimate state, models with triangular compression stress block, and strain-softening type tension stress block can be used as exact solution for ultra high performance concrete. For the conservative and convenient design of section, modified rectangular stress block model can be used with strain softening type tension stress block.

Evaluation of Fundamental UHPC Properties According to the Shape of Steel Fiber

2010 ◽  
Vol 452-453 ◽  
pp. 717-720 ◽  
Author(s):  
Gum Sung Ryu ◽  
Su Tae Kang ◽  
Jung Jun Park ◽  
Kyung Taek Koh ◽  
Sung Wook Kim
Keyword(s):  
Aspect Ratio ◽  
Flexural Strength ◽  
High Performance ◽  
High Performance Concrete ◽  
Steel Fibers ◽  
Flexural Behavior ◽  
Ultra High Performance Concrete ◽  
Aspect Ratios ◽  
Strength Tests ◽  
Shaped Fibers

This paper intends to examine the effects if the length and shape of steel fibers on the mechanical characteristics of ultra-high performance concrete (UHPC). Accordingly, the length (l) of the steel fibers with diameter (d) of 0.2 mm is varied as 13 mm, 16.3 mm and 19.5 mm and their corresponding aspect ratios (l/d) are 65, 82 and 98. Straight and wave-shaped fibers are adopted to manufacture UHPC. Thereafter, the effects of the aspect ratio and characteristics of the wave-shape of the steel fibers on the strength characteristics of UHPC are examined through compressive and flexural strength tests. The results showed small differences in the workability and compressive behavior but revealed that changing the length of the fibers and increasing the aspect ratio are improving the flexural behavior of UHPC. Specifically, the flexural strength was enhanced by 25% and the flexural toughness by 30%. Compared to rectilinear fibers, the adoption of wave-shaped fibers is seen to degrade the flexural behavior regardless of the aspect ratio. Consequently, using straight steel fibers and adopting larger aspect ratio seems advisable to improve the toughness of UHPC.

SUSTAINABLE ULTRA-HIGH-PERFORMANCE GLASS CONCRETE FOR INFRASTRUCTURES

2017 ◽  
Vol 4 (1) ◽  
Author(s):  
Arezki Tagnit-Hamou ◽  
Nancy A. Soliman
Keyword(s):  
High Performance ◽  
Glass Powder ◽  
Mechanical Performance ◽  
High Performance Concrete ◽  
Low Cost ◽  
Research Work ◽  
High Strength ◽  
Quartz Powder ◽  
Ultra High Performance Concrete ◽  
Powder Particles

This paper presents research work on the development of a green type of ultra-high-performance concrete using ground glass powders with different degrees of fineness (UHPGC). This article presents the development of an innovative, low-cost, and sustainable UHPGC through the use of glass powder to replace cement, and quartz powder particles. An UHPGC with a compressive strength (fc) of up to 220 MPa was prepared and its fresh, and mechanical properties were investigated. The test results indicate that the fresh UHPGC properties were improved when the cement and quartz powder were replaced with non-absorptive glass powder particles. The strength improvement can be attributed to the glass powder’s pozzolanicity and to its mechanical performance (very high strength and elastic modulus of glass). A case study of using this UHPGC is presented through the design and construction of a footbridge. Erection of footbridge at University of Sherbrooke Campus using UHPGC is also presented as a full-scale application.

Evaluation of Flexural Performance in UHPC(Ultra High Performance Concrete) According to Placement Methods

2009 ◽  
Vol 417-418 ◽  
pp. 581-584 ◽  
Author(s):  
Gum Sung Ryu ◽  
Su Tae Kang ◽  
Jung Jun Park ◽  
Gyung Taek Koh
Keyword(s):  
Flexural Strength ◽  
High Performance ◽  
High Performance Concrete ◽  
Initial Crack ◽  
Ultra High Performance Concrete ◽  
Remarkable Feature ◽  
Flexural Performance ◽  
Placement Method ◽  
Compaction Properties ◽  
And Diffusion

Apart from its high compressive, tensile and flexural strengths reaching approximately 200MPa, 15MPa and 35MPa, respectively, Ultra High Performance Concrete (UHPC) is characterized by its high resistance against degrading factors that can delay their penetration and diffusion speeds down to 1/20 to maximum 1/10,000 compared to ordinary concrete. UHPC also exhibits self-compaction properties with a slump flow of about 220mm. Furthermore, the most remarkable feature of UHPC is the improvement of its flexural strength and toughness through the admixing of steel fiber. Accordingly, this study evaluates the effects of the placement method on the flexural performance of UHPC. As a result, the flexural strength of UHPC appears to be extremely dependent on the placement method with variation of the maximum flexural strength up to 2 to 3 times while poor influence is observed on the initial crack strength.

scholarly journals Mechanical Performance and Microstructure of Ultra-High-Performance Concrete Modified by Calcium Sulfoaluminate Cement

2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Meimei Song ◽  
Chuanlin Wang ◽  
Ying Cui ◽  
Qiu Li ◽  
Zhiyang Gao
Keyword(s):  
Compressive Strength ◽  
High Performance ◽  
Mechanical Performance ◽  
High Performance Concrete ◽  
Autogenous Shrinkage ◽  
Ultra High Performance Concrete ◽  
Maximum Heat ◽  
Degree Of Hydration ◽  
Calcium Sulfoaluminate ◽  
Shrinkage Property

High autogenous shrinkage property is one of the disadvantages of ultra-high-performance concrete (UHPC), which may induce early age cracking and threaten the safety of concrete structure. In the present study, different dosages of calcium sulfoaluminate (CSA) cement were added in UHPC as an effective expansive binder. Hydration mechanism, autogenous shrinkage property, and compressive strength of UHPC were carried out to investigate the effect of CSA addition on the mechanical properties of UHPC. Scanning electron microscopy was also employed to characterize the intrinsic microstructural reasons relating to the changes in macroproperties. Based on the XRD diagram, increasing formation of ettringite and Ca(OH)2 can be found with increasing CSA content up to 15%. In the heat flow results of UHPC with 10% CSA addition, the maximum heat release increases to 2.6 mW/g, which is 8.3% higher than the reference UHPC, suggesting a higher degree of hydration with CSA addition. The results in autogenous shrinkage show that CSA expansion agent plays a significantly beneficial role in improving the autogenous shrinkage of UHPC. The corresponding autogenous shrinkage of UHPC is −59.66 μ ε , −131.11 μ ε , and −182.31 μ ε , respectively, at 7 d with 5%, 10%, and 15% addition, which is 108%, 117%, and 123% reduction compared to the reference specimen without CSA. In terms of compressive strength, UHPC with 5%, 10%, 15%, and 20% CSA addition has 10.5%, 17.4%, 30.2%, and 22.1% higher compressive strength than that for the reference UHPC at 28 d. Microstructural study shows that there is an extremely dense microstructure in both the bulk matrix and interfacial transition zone of UHPC with 10% CSA addition, which can be attributed to the higher autogenous shrinkage property and can therefore result in higher mechanical performance.

Sign in / Sign up

Export Citation Format

Share Document