Variation in the primary and secondary metabolites derived from the isoprenoid pathway in the Perovskia species in response to different wavelengths generated by light emitting diodes (LEDs)

2019 ◽  
Vol 140 ◽  
pp. 111592 ◽  
Author(s):  
Zahra Ghaffari ◽  
Mehdi Rahimmalek ◽  
Mohammad R. Sabzalian
HortScience ◽  
2008 ◽  
Vol 43 (7) ◽  
pp. 2243-2244 ◽  
Author(s):  
Mark G. Lefsrud ◽  
Dean A. Kopsell ◽  
Carl E. Sams

The use of light-emitting diodes (LEDs) for plant production is a new field of research that has great promise to optimize wavelength-specific lighting systems for precise management of plant physiological responses and important secondary metabolite production. In our experiment, hydroponically cultured kale plants (Brassica oleracea L. var. acephala D.C.) were grown under specific LED wavelength treatments of 730, 640, 525, 440, and 400 nm to determine changes in the accumulation of chlorophylls, carotenoids, and glucosinolates. Maximum accumulation, on a fresh mass basis, of chlorophyll a and b and lutein occurred at the wavelength of 640 nm, whereas β-carotene accumulation peaked under the 440-nm treatment. However, when lutein was measured on a dry mass basis, maximum accumulation was shifted to 440 nm. Sinigrin was the only glucosinolate to respond to wavelength treatments. Wavelength control using LED technology can affect the production of secondary metabolites such as carotenoids and glucosinolates with irradiance levels also a factor in kale. Management of irradiance and wavelength may hold promise to maximize nutritional potential of vegetable crops grown in controlled environments.


2000 ◽  
Vol 660 ◽  
Author(s):  
Thomas M. Brown ◽  
Ian S. Millard ◽  
David J. Lacey ◽  
Jeremy H. Burroughes ◽  
Richard H. Friend ◽  
...  

ABSTRACTThe semiconducting-polymer/injecting-electrode heterojunction plays a crucial part in the operation of organic solid state devices. In polymer light-emitting diodes (LEDs), a common fundamental structure employed is Indium-Tin-Oxide/Polymer/Al. However, in order to fabricate efficient devices, alterations to this basic structure have to be carried out. The insertion of thin layers, between the electrodes and the emitting polymer, has been shown to greatly enhance LED performance, although the physical mechanisms underlying this effect remain unclear. Here, we use electro-absorption measurements of the built-in potential to monitor shifts in the barrier height at the electrode/polymer interface. We demonstrate that the main advantage brought about by inter-layers, such as poly(ethylenedioxythiophene)/poly(styrene sulphonic acid) (PEDOT:PSS) at the anode and Ca, LiF and CsF at the cathode, is a marked reduction of the barrier to carrier injection. The electro- absorption results also correlate with the electroluminescent characteristics of the LEDs.


2003 ◽  
Vol 764 ◽  
Author(s):  
X. A. Cao ◽  
S. F. LeBoeuf ◽  
J. L. Garrett ◽  
A. Ebong ◽  
L. B. Rowland ◽  
...  

Absract:Temperature-dependent electroluminescence (EL) of InGaN/GaN multiple-quantum-well light-emitting diodes (LEDs) with peak emission energies ranging from 2.3 eV (green) to 3.3 eV (UV) has been studied over a wide temperature range (5-300 K). As the temperature is decreased from 300 K to 150 K, the EL intensity increases in all devices due to reduced nonradiative recombination and improved carrier confinement. However, LED operation at lower temperatures (150-5 K) is a strong function of In ratio in the active layer. For the green LEDs, emission intensity increases monotonically in the whole temperature range, while for the blue and UV LEDs, a remarkable decrease of the light output was observed, accompanied by a large redshift of the peak energy. The discrepancy can be attributed to various amounts of localization states caused by In composition fluctuation in the QW active regions. Based on a rate equation analysis, we find that the densities of the localized states in the green LEDs are more than two orders of magnitude higher than that in the UV LED. The large number of localized states in the green LEDs are crucial to maintain high-efficiency carrier capture at low temperatures.


Sign in / Sign up

Export Citation Format

Share Document