Enhancing mechanical properties and corrosion resistance of a high strength 7A99 Al alloy by introducing pre-rolling in solution and aging treatments

2021 ◽  
pp. 162972
Author(s):  
Liang Chen ◽  
Yuzhu Hou ◽  
Zhigang Li ◽  
Guoqun Zhao ◽  
Cunsheng Zhang
Keyword(s):  
Mechanical Properties ◽  
Corrosion Resistance ◽  
High Strength ◽  
Al Alloy ◽  
Mechanical Properties And Corrosion

Effects of Cu on mechanical properties and corrosion resistance on (Ti36.1Zr33.2Ni5.8Be24.9)100-xCux alloys

2020 ◽  
Vol 10 (6) ◽  
pp. 812-818
Author(s):  
Xiangjie Yang ◽  
Xinhua Huang ◽  
Linhao Zhu ◽  
Hongmin Guo ◽  
Hualan Jin
Keyword(s):  
Mechanical Properties ◽  
Corrosion Resistance ◽  
Thermal Properties ◽  
Plastic Strain ◽  
Yield Strength ◽  
Metallic Glass ◽  
High Strength ◽  
Mechanical Behaviors ◽  
Cu Content ◽  
Mechanical Properties And Corrosion

Due to high strength, perfect plasticity and higher hardness, bulk metallic glass (BMG) has been widely concerned. The work used the vaccum casting of copper-formed mold to establish (Ti36.1Zr33.2Ni5.8Be24.9)100-xCux, where x = 3, 5, 7, 9 and 11. Thermal properties, mechanical behaviors of compression, and corrosion resistance in the proposed compounds were investigated. The results show that the increase in Cu content enhances the heat resistance and the forming of glass of BMGs, small amount of fine dendritic crystals presents in BMG when x = 3, and the best corrosion resistance and mechanical properties can be obtained when x = 7, the yield strength, fracture strength and plastic strain can reach 1496.15 MPa, 2003.44 MPa and 19.19%, respectively.

Corrosion of New Wrought Magnesium Alloys

2005 ◽  
Vol 488-489 ◽  
pp. 839-844 ◽  
Author(s):  
Young Gee Na ◽  
Dan Eliezer ◽  
Kwang Seon Shin
Keyword(s):  
Mechanical Properties ◽  
Corrosion Resistance ◽  
Magnesium Alloys ◽  
Corrosion Behavior ◽  
Weight Ratio ◽  
Hot Extrusion ◽  
High Strength ◽  
Tensile Tests ◽  
Mechanical Properties And Corrosion ◽  
Extrusion Method

The development of new components with magnesium alloys for the automotive industry has increased in recent years due to their high potential as structural materials for low density and high strength/weight ratio demands. However, the limited mechanical properties of the magnesium alloys have led to search new kind of magnesium alloys for better strength and ductility. The main objective of this research is to investigate the mechanical properties and the corrosion behavior of new wrought magnesium alloys; Mg-Zn-Ag (ZQ) and Mg-Zn-Si (ZS) alloys. The ZQ6X and ZS6X samples were fabricated using hot extrusion method. Tensile tests and immersion tests were carried out on the specimens from the extruded rods, which contained different amounts of silver or silicon, in order to evaluate the mechanical properties and corrosion behavior. The microstructure was examined using optical and electron microscopy (TEM and SEM) and EDS. The results showed that the addition of silver improved the mechanical properties but decreased the corrosion resistance. The addition of silicon improved both mechanical properties and corrosion resistance. These results can be explained by the effects of alloying elements on the microstructures of the Mg-Zn alloys such as grain size and precipitates caused by the change in precipitation and recrystallization behavior.

scholarly journals The Effect of Cu and Mo on Mechanical Properties and Corrosion Resistance of Austempered Ductile Iron

MESIN ◽  
2020 ◽  
Vol 11 (2) ◽  
Author(s):  
Sulardjaka Sulardjaka ◽  
Yusuf Umardani ◽  
Agus Suprihanto
Keyword(s):  
Mechanical Properties ◽  
Corrosion Resistance ◽  
Ductile Iron ◽  
Brinell Hardness ◽  
High Strength ◽  
Hardness Test ◽  
Salt Bath ◽  
Austempered Ductile Iron ◽  
Immersion Corrosion ◽  
Mechanical Properties And Corrosion

The metal casting is the most economical manufacturing process. It can make products with complex geometries in one process. Austempered Ductile Iron (ADI) is a cast iron product that has high prospects for application, because ADI has a high strength closed to forged iron. The purpose of this study is to investigate the effect of addition of Cu and Mo on mechanical properties and corrosion resistance of ADI. Cu is added with percentages of 0.5 and 1% by weight, while Mo is added by percentages of 0.3 and 0.6% by weight. The austempering process is conducted on salt bath temperture 350 <sup>o</sup>C for 4 hours. The results of the process were characterized by hardness test, tensile test and corrosion resistance. Hardness and tensile strength of ADI were tested by Brinell hardness test based on ASTM E10 and ASTM E8 repectively. Corrosion resistance of ADI was tested by immersion corrosion testing based on ASTM G31 standard.  The results of this study indicate that the addition of Cu element significantly increases the strength of ADI. The addition of Mo element inhibits graphite nodularity and not significantly increases the mechanical properties. Addition of Mo increases corrosion resistance due the amount of retained austenite.

scholarly journals Effect of Rare-Earth Elements on the Corrosion Resistance of Flux-Cored Arc-Welded Metal with 10CrNi3MoV Steel

2018 ◽  
Vol 2018 ◽  
pp. 1-12 ◽  
Author(s):  
Kai Wang ◽  
Qinghua Lu ◽  
Zexin Jiang ◽  
Yaoyong Yi ◽  
Jianglong Yi ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Corrosion Resistance ◽  
Rare Earth ◽  
Rare Earth Elements ◽  
Electrochemical Impedance ◽  
Hsla Steel ◽  
High Strength ◽  
Cored Wire ◽  
Uniform Microstructure ◽  
Mechanical Properties And Corrosion

We modified the content of rare-earth elements (REE) in the flux-cored wire used to produce welds of high-strength low-alloy (HSLA) steel. The effect of REE addition on the microstructure as well as on the mechanical and electrochemical properties of the welded metal (WM) was investigated. REE-modified welded metals show very different responses during electrochemical impedance spectroscopy and the potentiodynamic polarization tests. The results indicate that the addition of REE of 0.3 wt.% facilitates a more uniform microstructure and improves both mechanical properties and corrosion resistance in welded metals.

Influence of Grain Size on Corrosion Resistance of a HSLA Steel

2012 ◽  
Vol 557-559 ◽  
pp. 143-146 ◽  
Author(s):  
Yan Tang Chen ◽  
Kai Guang Zhang
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Corrosion Resistance ◽  
Mechanical Performance ◽  
Hsla Steel ◽  
High Strength ◽  
Corrosion Resistant ◽  
Hsla Steels ◽  
Mechanical Properties And Corrosion ◽  
Mn Steel

The mechanical performance, workability, weldability and corrosion resistance of structural high strength low alloy (HSLA) steels used in offshore engineering have been generally required. The effect of grain size on the corrosion resistant performance of a C-Mn structural steel has been investigated with stress on hunting a appropriate grain size to balance mechanical properties and corrosion resistant performance. The results showed that the C-Mn steel with grain size in 10～25μm scope provided expected mechanical properties and corrosion resistance.

Sign in / Sign up

Export Citation Format

Share Document