Enhanced thermal stability of lactic acid bacteria during spray drying by intracellular accumulation of calcium

2020 ◽  
Vol 279 ◽  
pp. 109975 ◽  
Author(s):  
Yan Wang ◽  
Fan Hao ◽  
Wenjie Lu ◽  
Xiangshu Suo ◽  
Elise Bellenger ◽  
...  
1999 ◽  
Vol 62 (7) ◽  
pp. 773-777 ◽  
Author(s):  
GIANLUIGI MAURIELLO ◽  
MARIA APONTE ◽  
ROSAMARIA ANDOLFI ◽  
GIANCARLO MOSCHETTI ◽  
FRANCESCO VILLANI

Cell survival, cellular damage, and antagonistic activity were investigated after spray-drying of four bacteriocin-producing strains of lactic acid bacteria: Lactococcus lactis subsp. lactis 140, isolated from natural whey culture and producing a narrow-inhibitory spectrum bacteriocin); L. lactis subsp. lactis G35, isolated from pizza dough and producing nisin; Lactobacillus curvatus 32Y and Lactobacillus sp. 8Z, isolated from dry sausages. Trials were performed with bacteria suspended in skimmed milk or directly grown in whey. Three air temperatures at the inlet of the drier (160, 180, and 200°C) and three flow rates (10, 13, and 17 ml/min) were assayed. Cell viability and bacteriocin activity of the dried materials were determined immediately after the process and after 5, 15, 30, and 60 days of storage at 4°C. There was no significant difference between the two feeding suspensions in cell survival, always decreasing with the increase of inlet-air temperature. No loss of bacteriocin activity was detected in reconstituted powders, nor was any loss of ability to produce bacteriocin found after drying. Investigations of sensitivity to NaCl revealed only temporary damage to dried bacteria. During storage for 2 months at 4°C, all samples, but mainly the lactococcal strains, displayed a gradual decrease in cell survival. Bacteriocin activity remained at the same level, allowing powders to be considered as effective biopreservatives.


2011 ◽  
Vol 335-336 ◽  
pp. 153-156
Author(s):  
Xue Li Wu ◽  
Jian Hui Qiu ◽  
Lin Lei ◽  
Yang Zhao ◽  
Eiichi Sakai

To consider the effective utilization of plastics and agricultural wastes, rice straw fibre was extracted from agricultural wastes, and then composited with polylactic acid(PLA). The thermal stability of straw/poly(lactic acid)(straw/PLA) composites decreased (Thermogravimetric Analysis, TGA). Tensile strength, fracture strain and sharply impact strength of straw/PLA were decreased with the increase of filler content and grain size of straw. Yong’s modulus were increased as the increasing of straw content.


2019 ◽  
Vol 972 ◽  
pp. 172-177
Author(s):  
Sirirat Wacharawichanant ◽  
Patteera Opasakornwong ◽  
Ratchadakorn Poohoi ◽  
Manop Phankokkruad

This work studied the effects of various types of cellulose fibers on the morphology, mechanical and thermal properties of poly(lactic acid) (PLA)/propylene-ethylene copolymer (PEC) (90/10 w/w) blends. The PLA/PEC blends before and after adding cellulose fibers were prepared by melt blending method in the internal mixer and molded by compression method. The morphological analysis observed that the presence of cellulose in PLA did not change the phase morphology of PLA, and PLA/cellulose composite surfaces were observed the cellulose fibers inserted in PLA matrix and fiber pull-out. The phase morphology of PLA/PEC blends was changed from brittle fracture to ductile fracture behavior and showed the phase separation between PLA and PEC phases. The presence of celluloses did not improve the compatibility between PLA and PEC phases. The tensile stress and strain curves found that the tensile stress of PLA was the highest value. The addition of all celluloses increased Young’s modulus of PLA. The PEC presence increased the tensile strain of PLA over two times when compared with neat PLA and PLA was toughened by PEC. The incorporation of cellulose fibers in PLA/PEC blends could improve Young’s modulus, tensile strength, and stress at break of the blends. The thermal stability showed that the degradation temperatures of all types of cellulose were less than the degradation temperatures of PLA. Thus, the incorporation of cellulose in PLA could not enhance the thermal stability of PLA composites and PLA/PEC composites. The degradation temperature of PEC was the highest value, but it could not improve the thermal stability of PLA. The incorporation of cellulose fibers had no effect on the melting temperature of the PLA blend and composites.


2020 ◽  
Vol 837 ◽  
pp. 174-180
Author(s):  
Sirirat Wacharawichanant ◽  
Attachai Sriwattana ◽  
Kulaya Yaisoon ◽  
Manop Phankokkruad

This work studied the morphology, mechanical and thermal properties of poly (lactic acid) (PLA)/ethylene-octene copolymer (EOC) (80/20) blends with different organoclay types. Herein, EOC was introduced to toughening PLA by melt blending and organoclay was used to improve compatibility and tensile properties of the blends. The two organoclay types were nanoclay surface modified with aminopropyltriethoxysilane 0.5-5 wt% and octadecylamine 15-35% (Clay-ASO) and nanoclay surface modified with dimethyl dialkyl (C14-C18) amine 35-45 wt% (Clay-DDA). The organoclay contents were 3, 5 and 7 phr. Scanning electron microscope (SEM) observation results revealed PLA/EOC blends demonstrated a two-phase separation of dispersed EOC phase and PLA matrix phase. The addition of organoclay significantly improved the compatibility between PLA and EOC phases due to EOC droplet size decreased dominantly in PLA matrix, so organoclay could act as an effective compatibilizer. The incorporation of organoclay increased significantly tensile strength of PLA/EOC/organoclay composites while Young’s modulus increased with 5 phr of organoclay. The thermal stability of PLA/EOC blends did not change when compared with neat PLA, and when added Clay-ASO in the blends could improve the thermal stability of the PLA/EOC blends.


Sign in / Sign up

Export Citation Format

Share Document