Morphology and Properties of Poly(Lactic Acid)/Ethylene-Octene Copolymer Blends with Different Organoclay Types

2020 ◽  
Vol 837 ◽  
pp. 174-180
Author(s):  
Sirirat Wacharawichanant ◽  
Attachai Sriwattana ◽  
Kulaya Yaisoon ◽  
Manop Phankokkruad
Keyword(s):  
Thermal Stability ◽  
Lactic Acid ◽  
Poly Lactic Acid ◽  
Mechanical And Thermal Properties ◽  
Two Phase ◽  
Copolymer Blends ◽  
Ethylene Octene Copolymer ◽  
Surface Modified ◽  
Thermal Stability Of ◽  
Observation Results

This work studied the morphology, mechanical and thermal properties of poly (lactic acid) (PLA)/ethylene-octene copolymer (EOC) (80/20) blends with different organoclay types. Herein, EOC was introduced to toughening PLA by melt blending and organoclay was used to improve compatibility and tensile properties of the blends. The two organoclay types were nanoclay surface modified with aminopropyltriethoxysilane 0.5-5 wt% and octadecylamine 15-35% (Clay-ASO) and nanoclay surface modified with dimethyl dialkyl (C14-C18) amine 35-45 wt% (Clay-DDA). The organoclay contents were 3, 5 and 7 phr. Scanning electron microscope (SEM) observation results revealed PLA/EOC blends demonstrated a two-phase separation of dispersed EOC phase and PLA matrix phase. The addition of organoclay significantly improved the compatibility between PLA and EOC phases due to EOC droplet size decreased dominantly in PLA matrix, so organoclay could act as an effective compatibilizer. The incorporation of organoclay increased significantly tensile strength of PLA/EOC/organoclay composites while Young’s modulus increased with 5 phr of organoclay. The thermal stability of PLA/EOC blends did not change when compared with neat PLA, and when added Clay-ASO in the blends could improve the thermal stability of the PLA/EOC blends.

Morphology and Properties of Poly(Lactic Acid)/Ethylene-Octene Copolymer Nanocomposites

2019 ◽  
Vol 953 ◽  
pp. 47-52
Author(s):  
Sirirat Wacharawichanant ◽  
Attachai Sriwattana ◽  
Kulaya Yaisoon ◽  
Manop Phankokkruad
Keyword(s):  
Thermal Stability ◽  
Tensile Strength ◽  
Lactic Acid ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Poly Lactic Acid ◽  
Mechanical And Thermal Properties ◽  
Melt Mixing ◽  
Ethylene Octene Copolymer ◽  
Thermal Stability Of

The effects of the montmorillonite clay surface modified with 0.5-5 wt% aminopropyltriethoxysilane and 15-35% octadecylamine (Clay-APTSO) on morphology, mechanical and thermal properties of poly(lactic acid) (PLA)/ethylene-octene copolymer (EOC)/Clay-APTSO composites were investigated. The blends of PLA/EOC with and without Clay-APTSO were prepared by melt mixing in an internal mixer. Scanning electron microscopy analysis observed the morphology of PLA/EOC blends demonstrated a phase separation of minor phase and matrix phase. The addition of Clay-APTSO in PLA/EOC blends showed significant decreased in droplet size of dispersed EOC phase, thus, Clay-APTSO acted as an effective compatibilizer in the PLA/EOC blends. The results of tensile properties found the decrease of Young’s modulus of PLA when added EOC due to the low modulus and flexibility of EOC. While the incorporation of Clay-APTSO increased significantly Young’s modulus of PLA/EOC blends at low EOC and Clay-APTSO content. The strain at break of the blends increased with the increase of EOC loading, this indicated the presence of EOC enhanced the elongation at break of PLA, while the addition Clay-APTSO reduced the strain at break of PLA/EOC blends. The tensile strength of all blend compositions improved when added Clay-APTSO and the tensile strength showed the highest value at 3 phr of Clay-APTSO. The thermal stability of PLA/EOC blends did not change when compared with neat PLA, and when added Clay-APTSO in the blends could improve the thermal stability of the PLA/EOC blends.

Morphology, Mechanical and Thermal Properties of Poly(Lactic Acid)/Propylene-Ethylene Copolymer/Cellulose Composites

2019 ◽  
Vol 972 ◽  
pp. 172-177
Author(s):  
Sirirat Wacharawichanant ◽  
Patteera Opasakornwong ◽  
Ratchadakorn Poohoi ◽  
Manop Phankokkruad
Keyword(s):  
Thermal Stability ◽  
Lactic Acid ◽  
Thermal Properties ◽  
Tensile Stress ◽  
Cellulose Fibers ◽  
Phase Morphology ◽  
Poly Lactic Acid ◽  
Mechanical And Thermal Properties ◽  
Ethylene Copolymer ◽  
Thermal Stability Of

This work studied the effects of various types of cellulose fibers on the morphology, mechanical and thermal properties of poly(lactic acid) (PLA)/propylene-ethylene copolymer (PEC) (90/10 w/w) blends. The PLA/PEC blends before and after adding cellulose fibers were prepared by melt blending method in the internal mixer and molded by compression method. The morphological analysis observed that the presence of cellulose in PLA did not change the phase morphology of PLA, and PLA/cellulose composite surfaces were observed the cellulose fibers inserted in PLA matrix and fiber pull-out. The phase morphology of PLA/PEC blends was changed from brittle fracture to ductile fracture behavior and showed the phase separation between PLA and PEC phases. The presence of celluloses did not improve the compatibility between PLA and PEC phases. The tensile stress and strain curves found that the tensile stress of PLA was the highest value. The addition of all celluloses increased Young’s modulus of PLA. The PEC presence increased the tensile strain of PLA over two times when compared with neat PLA and PLA was toughened by PEC. The incorporation of cellulose fibers in PLA/PEC blends could improve Young’s modulus, tensile strength, and stress at break of the blends. The thermal stability showed that the degradation temperatures of all types of cellulose were less than the degradation temperatures of PLA. Thus, the incorporation of cellulose in PLA could not enhance the thermal stability of PLA composites and PLA/PEC composites. The degradation temperature of PEC was the highest value, but it could not improve the thermal stability of PLA. The incorporation of cellulose fibers had no effect on the melting temperature of the PLA blend and composites.

Influence of Cellulose Fiber Content on Morphology and Properties of Poly(Lactic Acid)/Propylene-Ethylene Copolymer/Cellulose Composites

2021 ◽  
Vol 315 ◽  
pp. 128-133
Author(s):  
Sirirat Wacharawichanant ◽  
Patteera Opasakornwong ◽  
Ratchadakorn Poohoi ◽  
Manop Phankokkruad
Keyword(s):  
Lactic Acid ◽  
Thermal Properties ◽  
Cellulose Fiber ◽  
Poly Lactic Acid ◽  
Mechanical And Thermal Properties ◽  
Two Phase ◽  
Degradation Temperature ◽  
Cellulose Composites ◽  
Ethylene Copolymer ◽  
Thermal Stability Of

This work studied the effects of medium-length fibrous cellulose (MFC) on the morphology, mechanical and thermal properties of poly(lactic acid) (PLA)/propylene-ethylene copolymer (PEC) (90/10) blends. The morphological analysis of PLA/MFC composites observed MFC fibers inserted in the PLA matrix and MFC appeared agglomeration when added high MFC loading. The phase morphology showed the two-phase separation of PLA/PEC blends. The presence of PEC reduced the agglomeration of MFC fibers in polymer matrix. The tensile stress and strain curves found that the ultimate stress of PLA was the highest value and the addition of MFC increased Young’s modulus of PLA/MFC and PLA/PEC/MFC composites. The PEC presence improved the strain at breaking point of PLA/PEC blends. The thermal properties found that the incorporation of MFC did not improve the thermal stability of PLA/MFC and PLA/PEC/MFC composites due to the PLA had degradation temperature higher than MFC.

Enhanced mechanical and thermal properties of poly (lactic acid)/bamboo fiber composites via surface modification

2018 ◽  
Vol 37 (12) ◽  
pp. 841-852 ◽  
Author(s):  
Guang Hu ◽  
Shenyang Cai ◽  
Yinghui Zhou ◽  
Naiwen Zhang ◽  
Jie Ren
Keyword(s):  
Thermal Stability ◽  
Lactic Acid ◽  
Coupling Agent ◽  
Solution Treatment ◽  
Fiber Composites ◽  
Bamboo Fiber ◽  
Poly Lactic Acid ◽  
Mechanical And Thermal Properties ◽  
Thermal Stability Of ◽  
Agent Treatment

Three different kinds of surface treatment procedures were used to modify the surface of bamboo fiber: alkali solution treatment (NaOH), alkali and silane coupling agent treatment (NaOH–KH550) and alkali and titanate coupling agent treatment (NaOH–NDZ201). Then the bamboo fiber reinforced poly (lactic acid) composites were prepared by Haake Mixer and characterized by FTIR spectroscopy, mechanics performance tests, differential scanning calorimetry analysis, thermogravimetric analysis, Vicat softening temperature, X-ray diffraction analysis and scanning electron microscopy. The results showed that incorporation of surface-treated bamboo fiber obviously improved the mechanical properties of poly (lactic acid). Especially, the tensile, flexural and impact strengths of poly (lactic acid) containing NaOH–NDZ201-treated bamboo fiber were higher than those of poly (lactic acid) containing NaOH and NaOH–KH550-treated bamboo fiber. Moreover, the NaOH–NDZ201-treated bamboo fiber also greatly enhanced the thermal stability of poly (lactic acid). The improvement of mechanical strengths and thermal stability of poly (lactic acid)/bamboo fiber composites might be due to the better interfacial adhesion between poly (lactic acid) and NaOH–NDZ201-treated bamboo fiber.

Improvement of Poly(Lactic Acid) Properties by Ethylene-Octene Copolymer and Organoclay

2020 ◽  
Vol 1009 ◽  
pp. 43-48
Author(s):  
Sirirat Wacharawichanant ◽  
Paweena Hanjai ◽  
Sanya Khongaio ◽  
Manop Phankokkruad
Keyword(s):  
Lactic Acid ◽  
Domain Size ◽  
Poly Lactic Acid ◽  
Mechanical And Thermal Properties ◽  
Melt Mixing ◽  
Before And After ◽  
Ethylene Octene Copolymer ◽  
Surface Modified ◽  
Internal Mixer ◽  
The Impact

The work studied the morphological, mechanical and thermal properties of poly(lactic acid) (PLA)/ethylene-octene copolymer (EOC) blends before and after adding the montmorillonite clay surface modified with 25-30% of octadecylamine (clay-ODA). The PLA/EOC blends and composites were prepared by melt mixing in an internal mixer. The EOC contents were 5, 10, 20, 30 wt% and clay-ODA contents were 1 and 3 phr. The morphology analysis showed that the addition of clay-ODA could improve the miscibility of PLA and EOC phases due to the domain size of dispersed EOC phase decreased with increasing clay-ODA content. X-ray diffraction revealed the formation of intercalated/exfoliated structure in PLA/clay-ODA and PLA blend composites. The mechanical properties showed that the impact strength of PLA/EOC blends dramatically increased with increasing EOC content up to 10 wt%. The strain at break of PLA blends increased with increasing EOC content. Moreover, the incorporation of clay-ODA increased significantly Young’s modulus of PLA and PLA/EOC blends with increasing clay-ODA content. The thermal stability of PLA/EOC blends improved with the addition of a small amount of clay-ODA.

The Mechanical Characteristics of Straw/poly(Lactic Acid) Composite Materials

2011 ◽  
Vol 335-336 ◽  
pp. 153-156
Author(s):  
Xue Li Wu ◽  
Jian Hui Qiu ◽  
Lin Lei ◽  
Yang Zhao ◽  
Eiichi Sakai
Keyword(s):  
Thermal Stability ◽  
Grain Size ◽  
Lactic Acid ◽  
Mechanical Characteristics ◽  
Fracture Strain ◽  
Filler Content ◽  
Agricultural Wastes ◽  
Poly Lactic Acid ◽  
Effective Utilization ◽  
Thermal Stability Of

To consider the effective utilization of plastics and agricultural wastes, rice straw fibre was extracted from agricultural wastes, and then composited with polylactic acid(PLA). The thermal stability of straw/poly(lactic acid)(straw/PLA) composites decreased (Thermogravimetric Analysis, TGA). Tensile strength, fracture strain and sharply impact strength of straw/PLA were decreased with the increase of filler content and grain size of straw. Yong’s modulus were increased as the increasing of straw content.

Preparation of lignin–silica hybrids and its application in intumescent flame-retardant poly(lactic acid) system

2012 ◽  
Vol 24 (8) ◽  
pp. 738-746 ◽  
Author(s):  
Rui Zhang ◽  
Xifu Xiao ◽  
Qilong Tai ◽  
Hua Huang ◽  
Jian Yang ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Lactic Acid ◽  
Flame Retardant ◽  
Flame Retardancy ◽  
Photoelectron Spectroscopy ◽  
Intumescent Flame Retardant ◽  
Poly Lactic Acid ◽  
Limiting Oxygen Index ◽  
Silica Hybrids ◽  
Thermal Stability Of

Lignin–silica hybrids (LSHs) were prepared by sol–gel method and characterized by Fourier transform infrared (FT-IR) spectra, X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). LSH and ammonium polyphosphate (APP) were added into poly(lactic acid) (PLA) as a novel intumescent flame-retardant (IFR) system to improve the flame retardancy of PLA. The flame-retardant effect of APP and LSH in PLA was studied using limiting oxygen index (LOI), vertical burning (UL-94) tests and cone calorimeter. The thermal stability of PLA/APP/LSH composites was evaluated by thermogravimetric analysis (TGA). Additionally, the morphology and components of char residues of the IFR-PLA composites were investigated by SEM and XPS. With the addition of APP/LSH to PLA system, the morphology of the char residue has obviously changed. Compared with PLA/APP and PLA/APP/lignin, a continuous and dense intumescent charring layer with more phosphor in PLA composites is formed, which exhibits better flame retardancy. All the results show that the combination of APP and LSH can improve the flame-retardant property and increase the thermal stability of PLA composites greatly.

Sign in / Sign up

Export Citation Format

Share Document