Optimization of surface roughness and tool wear in hard turning of austempered ductile iron (grade 3) using Taguchi method

Measurement ◽  
2016 ◽  
Vol 93 ◽  
pp. 108-116 ◽  
Author(s):  
D. Manivel ◽  
R. Gandhinathan
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Taguchi Method ◽  
Ductile Iron ◽  
Hard Turning ◽  
Austempered Ductile Iron ◽  
Grade 3 ◽  
Iron Grade

Grinding of Austempered Ductile Iron Grade 3 as Function of the Microcrystalline Al2O3 Grinding Wheels Composition

2015 ◽  
Vol 1105 ◽  
pp. 164-171 ◽  
Author(s):  
Lucas Benini ◽  
Walter Lindolfo Weingaertner ◽  
Eckart Uhlmann
Keyword(s):  
Ductile Iron ◽  
Machine Tools ◽  
Austempered Ductile Iron ◽  
Grinding Wheel ◽  
Grinding Wheels ◽  
Grinding Forces ◽  
Conventional Grinding ◽  
Grade 3 ◽  
Iron Grade ◽  
First Time

The conventional grinding wheels employment is an economically viable alternative on Austempered ductile iron (ADI) grinding. The machining of this iron is in most cases performed with superabrasive grinding wheels, requiring machine tools with higher costs. The ADI grinding with conventional grinding wheels can produce work results comparable to the superabrasive grinding wheels, followed by lower costs and flexibility in profile grinding, since these wheels can be easily re-profiled. The aim of this work is to verify the work results of grinding ADI Grade 3 employing conventional grinding wheels. The approach is based on the influence evaluation of different abrasive microcrystalline Al2O3 percentage in these tools on the force results and roughness values in the ADI grinding. The findings show a correlation between the grinding forces and the microcrystalline abrasive percentage of microcrystalline Al2O3, since lower forces were demanded for wheels with higher percentages. Regarding the surface parameters, there was a decrease in roughness values by employing less percentages. The originality of this research is reflected in the fact that it is the first time that the influence of the composition of conventional grinding wheels is investigated on ADI Grade 3 grinding. The results present in this research will contribute to the most appropriate conventional grinding wheel specification for the ADI Grade 3 grinding.

scholarly journals An experimental study on the effect of tool geometry on tool wear and surface roughness in hard turning

2020 ◽  
Vol 12 (9) ◽  
pp. 168781402095988
Author(s):  
Pham Minh Duc ◽  
Le Hieu Giang ◽  
Mai Duc Dai ◽  
Do Tien Sy
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Inclination Angle ◽  
Hard Turning ◽  
Rake Angle ◽  
Machining Process ◽  
Tool Geometry ◽  
Standard Tool ◽  
Inclination Angles ◽  
Mixed Ceramic

The main purpose of this study is to investigate the influence of tool geometry (cutting edge angle, rake angle, and inclination angle) and to optimize tool wear and surface roughness in hard turning of AISI 1055 (52HRC) hardened steel by using TiN coated mixed ceramic inserts. The results show that the inclination angle is the major factor affecting the tool wear and the surface roughness in hard turning. With the increase in negative rake and inclination angles, the tool wear decreases, and the surface roughness increases. However, the surface roughness will decrease when the inclination angle increases to overpass a certain limit. This is a new and significant point in the research of the hard turning process. From this result, the large negative inclination angle (λ = −10°) should be applied to reduce the surface roughness and the tool wear simultaneously. With the optimal cutting tool angles in the research, the hard machining process is improved remarkably with decreases of surface roughness and tool wear 8.3% and 41.3%, respectively in comparison with the standard tool angles. And the proposed tool-post design approach brings an effective method to change the tool insert angles using standard tool-holders to improve hard or other difficult-to-cut materials turning quality.

Turning of Austempered Ductile Iron with ceramic tools

2020 ◽  
pp. 095440542095715 ◽  
Author(s):  
A Fernández-Valdivielso ◽  
LN López de Lacalle ◽  
P Fernández-Lucio ◽  
H González
Keyword(s):  
Heat Treatment ◽  
Tool Wear ◽  
Ductile Iron ◽  
High Strength ◽  
Cutting Parameters ◽  
Precise Determination ◽  
Machining Process ◽  
Austempered Ductile Iron ◽  
Machining Time ◽  
Ceramic Tools

Austempered ductile iron castings (ADI) are characterized by the high strength and resistance to fatigue, impact, and wear. ADI mechanical properties are obtained by performing a heat treatment on ductile iron casting. Thus, the so-called ausferrite microstructure is achieved. However, heat treatment significantly affects ductile casting machinability. A precise determination of ADI microstructure, on the one hand, and to choose correct machining process parameters and tool wear control on the other, are essential to optimize cutting processes and for the introduction of ceramic inserts. Ceramics are an alternative to carbide tools. In this paper, ceramic tools for the dry turning of ADI castings are studied. Thus, different technical ceramics were analyzed, identifying the dominant wear mechanism and evolution. Tool wear rate magnitude was determined indirectly by the variation of cutting force along machining time. Finally, different tests helped to study ceramics wear sensitivity with respect to cutting parameters. Mixed ceramics of Al2O3 with TiC showed the best performance, followed by SiAlON ones.

Sign in / Sign up

Export Citation Format

Share Document