Design and preparation of a type of γ-Ce2S3@c-SiO2-coated red pigment with a plum pudding mosaic structure: The effect of pre-sintering temperature on pigment properties

2021 ◽  
Vol 311 ◽  
pp. 110699
Author(s):  
Fuling Wu ◽  
Xin Li ◽  
Yueming Li ◽  
Zhumei Wang ◽  
Yan Hong ◽  
...  
Keyword(s):  
Sintering Temperature ◽  
Mosaic Structure ◽  
Red Pigment

Electron Microscopy of Silicon Nitride-Based Ceramics

1991 ◽  
Vol 49 ◽  
pp. 926-927
Author(s):  
Gareth Thomas
Keyword(s):  
Electron Microscopy ◽  
High Temperature ◽  
Silicon Nitride ◽  
World Wide ◽  
Sintering Temperature ◽  
Liquid Phase Sintering ◽  
High Temperature Strength ◽  
Sintering Additives ◽  
Glass Forming ◽  
Dense Product

Silicon nitride and silicon nitride based-ceramics are now well known for their potential as hightemperature structural materials, e.g. in engines. However, as is the case for many ceramics, in order to produce a dense product, sintering additives are utilized which allow liquid-phase sintering to occur; but upon cooling from the sintering temperature residual intergranular phases are formed which can be deleterious to high-temperature strength and oxidation resistance, especially if these phases are nonviscous glasses. Many oxide sintering additives have been utilized in processing attempts world-wide to produce dense creep resistant components using Si3N4 but the problem of controlling intergranular phases requires an understanding of the glass forming and subsequent glass-crystalline transformations that can occur at the grain boundaries.

Synthesis and study the Structural and electrical and mechanical properties of High Temperature Superconductor Tl0.5Pb0.5Ba2Can-1Cun-xNixO2n+3-δ Substituted with nickel oxide for n=3

2018 ◽  
Vol 31 (3) ◽  
pp. 26 ◽  
Author(s):  
Laheeb. A. Mohammed ◽  
Kareem. A. Jasim
Keyword(s):  
Nickel Oxide ◽  
High Temperature Superconductor ◽  
Sintering Temperature ◽  
Concentration Effects ◽  
High Tc ◽  
Xrd Diffraction ◽  
Ni Content ◽  
High Tc Phase ◽  
Pure Phases ◽  
Critical Temperature Tc

   on this research is to study the effect of nickel oxide substitution on the pure phases superconductor Tl0.5Pb0.5Ba2Can-1Cun-xNixO2n+3-δ (n=3) where x=(0,0.2,0.4,0.6,0.8.and 1.0). The specimens in this work were prepared with used  procedure of solid state reaction with sintering temperature 8500C for 24 h .we used technical (4-prob)to calculated and the critical temperature Tc . The results of the XRD diffraction analysis showed that the structure for pure and doped phases was tetragonal with phases high-Tc phase (1223),(1212) and low-Tc phase (1202)  and add to the presence of some impure phase. It was noted the value a=b,c  the parameter of  the lattice increment  with the increment of Ni content. The increment of (NiO) concentration effects electrical resistivity, dielectric constant and the hardness.

Effect of spark plasma sintering temperature on structure and phase composition of Ti-Al-Nb-based alloys

2017 ◽  
Vol 59 (11-12) ◽  
pp. 1033-1036 ◽  
Author(s):  
Sherzod Kurbanbekov ◽  
Mazhyn Skakov ◽  
Viktor Baklanov ◽  
Batyrzhan Karakozov
Keyword(s):  
Phase Composition ◽  
Spark Plasma Sintering ◽  
Sintering Temperature ◽  
Plasma Sintering ◽  
Spark Plasma

scholarly journals Optimization of Sintering Process of Alumina Ceramics Using Response Surface Methodology

2021 ◽  
Vol 13 (12) ◽  
pp. 6739
Author(s):  
Darko Landek ◽  
Lidija Ćurković ◽  
Ivana Gabelica ◽  
Mihone Kerolli Mustafa ◽  
Irena Žmak
Keyword(s):  
Response Surface Methodology ◽  
Response Surface ◽  
Heating Rate ◽  
Sintering Temperature ◽  
Nonlinear Models ◽  
Slip Casting ◽  
Holding Time ◽  
Alumina Ceramics ◽  
Aqueous Suspensions ◽  
Temperature Heating

In this work, alumina (Al2O3) ceramics were prepared using an environmentally friendly slip casting method. To this end, highly concentrated (70 wt.%) aqueous suspensions of alumina (Al2O3) were prepared with different amounts of the ammonium salt of a polycarboxylic acid, Dolapix CE 64, as an electrosteric dispersant. The stability of highly concentrated Al2O3 aqueous suspensions was monitored by viscosity measurements. Green bodies (ceramics before sintering) were obtained by pouring the stable Al2O3 aqueous suspensions into dry porous plaster molds. The obtained Al2O3 ceramic green bodies were sintered in the electric furnace. Analysis of the effect of three sintering parameters (sintering temperature, heating rate and holding time) on the density of alumina ceramics was performed using the response surface methodology (RSM), based on experimental data obtained according to Box–Behnken experimental design, using the software Design-Expert. From the statistical analysis, linear and nonlinear models with added first-order interaction were developed for prediction and optimization of density-dependent variables: sintering temperature, heating rate and holding time.

Effect of High-Energy Milling and Sintering Temperature on the Properties of Al2O3-WC-Co Composites

2021 ◽  
Author(s):  
Heytor V. S. B. Azevêdo ◽  
Rafael A. Raimundo ◽  
David D. S. Silva ◽  
Luís M. F. Morais ◽  
Franciné A. Costa ◽  
...  
Keyword(s):  
Sintering Temperature ◽  
High Energy ◽  
High Energy Milling
Sign in / Sign up

Export Citation Format

Share Document