Room temperature plastic flow behaviour of Ti–6.8Mo–4.5Fe–1.5Al and Ti–10V–4.5Fe–1.5Al: Effect of grain size and strain rate

2007 ◽  
Vol 452-453 ◽  
pp. 219-227 ◽  
Author(s):  
A. Bhattacharjee ◽  
P. Ghosal ◽  
A.K. Gogia ◽  
S. Bhargava ◽  
S.V. Kamat
Keyword(s):  
Grain Size ◽  
Strain Rate ◽  
Plastic Flow ◽  
Room Temperature ◽  
Flow Behaviour

Superplasticity and Microstructure Evolution of Electrodeposited Nanocrystalline Nickel

2007 ◽  
Vol 551-552 ◽  
pp. 539-544 ◽  
Author(s):  
S. Ding ◽  
Kai Feng Zhang ◽  
Guo Feng Wang
Keyword(s):  
Grain Size ◽  
Strain Rate ◽  
Room Temperature ◽  
Tensile Tests ◽  
Uniaxial Tensile ◽  
Intergranular Cracking ◽  
Mean Grain Size ◽  
Electrodeposited Nickel ◽  
Superplastic Properties

Nanocrystalline pure nickel (nc-Ni) was produced by pulse electrodeposition and its superplastic properties at and above room temperature were investigated. The electrodeposited nickel has a narrow grain size distribution with a mean grain size of 70nm. Uniaxial tensile tests at room temperature showed that nc-Ni has a limited plasticity but high tensile strength up to 1GPa at strain rates between 10-5 and 10-2s-1. However, when the temperature increased to 420 and higher, test specimens showed uniform deformation and the elongation value was larger than 200%. A maximum elongation value of 380% was observed at 450°C and a strain rate of 1.67x10-3s-1, SEM and TEM were used to examine the microstructures of the as-deposited and deformed specimens. The results indicated that fracture was caused by intergranular cracking and most cracks were originated from the brittle oxide formed during the tensile test. Grain coarsening was observed in the deformed specimen. The role of temperature and strain on grain growth was evaluated by comparing the microstructure of deformed samples with that of samples statically annealed. Deformation mechanism was discussed based upon the deformed microstructure and strain rate jump tests.

Influence of Mg Content, Grain Size and Strain Rate on Mechanical Properties and DSA Behavior of Al-Mg Alloys Processed by ECAP and Annealing

2014 ◽  
Vol 794-796 ◽  
pp. 870-875 ◽  
Author(s):  
Min Zha ◽  
Yan Jun Li ◽  
Ragnvald H. Mathiesen ◽  
Christine Baumgart ◽  
Hans J. Roven
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Strain Rate ◽  
Room Temperature ◽  
Uniform Elongation ◽  
Mg Alloys ◽  
Lower Strain Rate ◽  
Lower Strain ◽  
Mg Content ◽  
Al Mg Alloys

Ultrafine-grained (UFG) binary Al-xMg (x=1, 5 and 7 wt %) alloys were processed by equal channel angular pressing (ECAP) at room temperature via route Bccombined with inter-pass annealing. The effects of Mg content, grain size and strain rate on mechanical properties and dynamic strain aging (DSA) behaviour of the Al-Mg alloys upon tensile testing at room temperature were studied. An increase in Mg content from 5 to 7 wt % leads to a pronounced increase in strength and uniform elongation in both the as-homogenized and as-ECAP Al-Mg alloys. Thereby, the Al-7Mg alloy, either prior to or after ECAP processing, possess significantly higher strength and comparable or even higher uniform elongation than the more dilute Al-Mg alloys. However, the as-ECAP Al-Mg alloys exhibit significantly higher strength but little work hardening and hence rather limited uniform elongation. In general, decreasing grain size leads to significant increase in strength while dramatic decrease in ductility. Moreover, DSA serration amplitudes increase with reducing grain size in the micrometer range. However, the UFG Al-Mg alloys exhibit much less DSA effect than the micrometer scaled grain size counterparts, i.e. probably due to the high dislocation densities and special grain boundary features in the UFG materials. Also, the Al-Mg alloys, especially those with a UFG structure, exhibit higher strength and ductility at lower strain rate than at higher strain rate, due mainly to enhanced DSA effect and hence work hardening at a lower strain rate.

Effects of Temperature, Strain Rate and Grain Size on Superplastic Behavior of Magnesium

2012 ◽  
Vol 488-489 ◽  
pp. 27-34 ◽  
Author(s):  
Muhammad Waseem Soomro ◽  
Thomas Rainer Neitzert
Keyword(s):  
Grain Size ◽  
Strain Rate ◽  
Magnesium Alloys ◽  
Room Temperature ◽  
Superplastic Forming ◽  
Experimental Results ◽  
Superplastic Behavior ◽  
Influence Of Temperature ◽  
Effects Of Temperature ◽  
Temperature Strain

The influence of temperature, grain size and strain rate on superplasticity of magnesium is investigated. Different approaches are compared along with their experimental results to show the variation in the amount of superplasticity by varying above mentioned parameters. At room temperature magnesium alloys usually have poor formability but recent studies of some alloys such as ZE10, AZ31, AZ61 AZ60, AZ80 and AZ91 are pointing that by varying the temperature along with grain size and strain rate improved formability is possible or even superplastic forming of these alloys can be achieved to meet the demands of automotive, aircraft and other weight conscious industries.

scholarly journals Nanoindentation-Induced Pile-Up in the Residual Impression of Crystalline Cu with Different Grain Size

2017 ◽  
Author(s):  
Jiangjiang Hu ◽  
Weiming Sun ◽  
Taihua Zhang ◽  
Yusheng Zhang
Keyword(s):  
Grain Size ◽  
Strain Rate ◽  
Room Temperature ◽  
Indentation Depth ◽  
Dislocation Motion ◽  
Coarse Grained ◽  
Ultrafine Grained ◽  
Pile Up ◽  
Different Grain Size ◽  
Multiple Slips

At room temperature, the indentation morphologies of crystalline copper with different grain size including nanocrystalline (NC), ultrafine-grained (UFG) and coarse-grained (CG) copper were studied by nanoindentation at the strain rate of 0.04/s without holding time at indentation depth of 2000 nm. As the grain size increasing, the height of the pile-up around the residual indentation increases and then has a slightly decrease in the CG Cu, While the area of the pile-up increases constantly. Our analysis has revealed that the dislocation motion and GB activities in the NC Cu, some cross- and multiple-slips dislocation insides the larger grain in the UFG Cu, and forest dislocations from the intragranular Frank-Read sources in the CG Cu, would directly induce these distinct pile-up effect.

Strain Rate Sensitivity of Ultrafine Grained FCC- and BCC-Type Metals

2006 ◽  
Vol 503-504 ◽  
pp. 781-786 ◽  
Author(s):  
Johannes May ◽  
Heinz Werner Höppel ◽  
Matthias Göken
Keyword(s):  
Grain Size ◽  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Room Temperature ◽  
Rate Sensitivity ◽  
Tensile Tests ◽  
Testing Temperature ◽  
Ultrafine Grain ◽  
Ultrafine Grain Size ◽  
Ultrafine Grained

The dependence of the strain rate sensitivity (SRS) of α-Fe and Al 99.5, as typical representatives of fcc- and bcc-type metals, on the testing temperature and with respect to the microstructure is investigated. In particular, the differences between conventional grain size (CG) and ultrafine grain size (UFG) are pointed out. UFG Al 99.5 generally shows an elevated SRS compared to CG Al 99.5. In case of α-Fe the SRS of the UFG state is decreased at room temperature, but increased at 200 °C, compared to the CG state. It is shown that the SRS also influences the ductility of UFG-metals in tensile tests.

The Effect of Grain Size and Strain Rate on the Tensile Ductility of Bulk Nanostructured Metals and Alloys

2009 ◽  
Vol 633-634 ◽  
pp. 393-410
Author(s):  
Guo Yong Wang ◽  
Jian She Lian ◽  
Qing Jiang
Keyword(s):  
Grain Size ◽  
Strain Rate ◽  
Room Temperature ◽  
Tensile Ductility ◽  
High Strength ◽  
Metals And Alloys ◽  
New Materials ◽  
Electrodeposition Technique ◽  
Nanostructured Metals ◽  
Coherent Property

The nanostructured metals and alloys are under intensive research worldwide and being developed into bulk forms for application. While these new materials offer record-high strength, their ductility is often inadequate and sometime rendering them unusable. Besides tailoring the nanostructure to achieve coexisting high strength and high ductility, to uncover the coherent property of this material is also important. This article reviews the recent researches finished in our lab. A set of nanostructured metals and alloys were synthesized by a direct current electrodeposition technique, and the effect of grain size and strain rate on the mechanical properties stressing on tensile ductility was systemically studied by tensile test at room temperature.

Influence of grain size on strain rate sensitivity in rolled Mg–3Al–3Sn alloy at room temperature

2013 ◽  
Vol 68 (5) ◽  
pp. 229-232 ◽  
Author(s):  
Hui-Yuan Wang ◽  
En-Song Xue ◽  
Xiao-Long Nan ◽  
Tao Yue ◽  
Yan-Peng Wang ◽  
...  
Keyword(s):  
Grain Size ◽  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Room Temperature ◽  
Rate Sensitivity
Sign in / Sign up

Export Citation Format

Share Document