The effect of joint configuration on residual stress and distortion of the 304 stainless steel multi-pass welded joints

2021 ◽  
pp. 103070
Author(s):  
Yuelin ZHANG ◽  
Li Tian
Keyword(s):  
Residual Stress ◽  
Stainless Steel ◽  
Welded Joints ◽  
304 Stainless Steel ◽  
Joint Configuration

Effect of Ultrasonic Impact Treatment on the Stress Corrosion Cracking of 304 Stainless Steel Welded Joints

2008 ◽  
Author(s):  
Gang Ma ◽  
Xiang Ling
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Stainless Steel ◽  
Stress Corrosion ◽  
Stress Corrosion Cracking ◽  
Welded Joints ◽  
Corrosion Cracking ◽  
Coarse Grained ◽  
304 Stainless Steel ◽  
Ultrasonic Impact Treatment

High tensile weld residual stress is an important factor contributing to stress corrosion cracking (SCC). Ultrasonic impact treatment (UIT) can produce compressive stresses on the surface of welded joints that negate the tensile stresses to enhance the SCC resistance of welded joints. In the present work, X-ray diffraction method was used to obtain the distribution of residual stress induced by UIT. The results showed that UIT could cause a large compressive residual stress up to 325.9MPa on the surface of the material. A 3D finite element model was established to simulate the UIT process by using a finite element software ABAQUS. The residual stress distribution of the AISI 304 stainless steel induced by UIT was predicted by finite element analysis. In order to demonstrate the improvement of the SCC resistance of the welded joints, the specimens were immersed in boiling 42% magnesium chloride solution during SCC testing, and untreated specimen cracked after immersion for 23 hours. In contrast, treated specimens with different coverage were tested for 1000 hours without visible stress corrosion cracks. The microstructure observation results revealed that a hardened layer was formed on the surface and the initial coarse-grained structure in the surface was refined into ultrafine grains. The above results indicate that UIT is an effective approach for protecting weldments against SCC.

Effect of Ultrasonic Impact Treatment on the Stress Corrosion Cracking of 304 Stainless Steel Welded Joints

2009 ◽  
Vol 131 (5) ◽  
Author(s):  
Xiang Ling ◽  
Gang Ma
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Stainless Steel ◽  
Stress Corrosion ◽  
Stress Corrosion Cracking ◽  
Welded Joints ◽  
Corrosion Cracking ◽  
Coarse Grained ◽  
304 Stainless Steel ◽  
Ultrasonic Impact Treatment

High tensile weld residual stress is an important factor contributing to stress corrosion cracking (SCC). Ultrasonic impact treatment (UIT) can produce compressive stresses on the surface of welded joints that negate the tensile stresses to enhance the SCC resistance of welded joints. In the present work, X-ray diffraction method was used to obtain the distribution of residual stress induced by UIT. The results showed that UIT could cause a large compressive residual stress in access of 300 MPa on the surface of the material. A 3D finite element model was established to simulate the UIT process by using the finite element software ABAQUS. The residual stress distribution of the AISI 304 stainless steel induced by UIT was predicted by finite element analysis. In order to demonstrate the improvement of the SCC resistance of the welded joints, the specimens were immersed in boiling 42% magnesium chloride solution during SCC testing, and untreated specimen cracked after immersion for 23 h. In contrast, treated specimens with different impact duration were tested for 1000 h without visible stress corrosion cracks. The microstructure observation results revealed that a hardened layer was formed on the surface and the initial coarse-grained structure in the surface was refined into ultrafine grains. The above results indicate that UIT is an effective approach for protecting weldments against SCC.

Numerical simulation of the effect of ultrasonic impact treatment on welding residual stress

2021 ◽  
pp. 2150175
Author(s):  
Tao Mo ◽  
Jingqing Chen ◽  
Pengju Zhang ◽  
Wenqian Bai ◽  
Xiao Mu ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Residual Stress ◽  
Compressive Stress ◽  
Welded Joints ◽  
Welding Process ◽  
Residual Compressive Stress ◽  
Welding Residual Stress ◽  
304 Stainless Steel ◽  
Residual Tensile Stress ◽  
Ultrasonic Impact Treatment

Ultrasonic impact treatment (UIT) is an effective method that has been widely applied in welding structure to improve the fatigue properties of materials. It combines mechanical impact and ultrasonic vibration to produce plastic deformation on the weld joints surface, which introduces beneficial compressive residual stress distribution. To evaluate the effect of UIT technology on alleviating the residual stress of welded joints, a novel numerical analysis method based on the inherent strain theory is proposed to simulate the stress superposition of welding and subsequent UIT process of 304 stainless steel. Meanwhile, the experiment according to the process was carried out to verify the simulation of residual stress values before and after UIT. By the results, optimization of UIT application could effectively reduce the residual stress concentration after welding process. Residual tensile stress of welded joints after UIT is transformed into residual compressive stress. UIT formed a residual compressive stress layer with a thickness of about 0.13 mm on the plate. The numerical simulation results are consistent with the experimental results. The work in this paper could provide theoretical basis and technical support for the reasonable evaluation of the ultrasonic impact on residual stress elimination and mechanical properties improvement of welded joints.

scholarly journals Creep-Rupture Behavior and Creep Strain Distribution of Welded Joints of 304 Stainless Steel Thick Plates.

1996 ◽  
Vol 45 (12) ◽  
pp. 1328-1333 ◽  
Author(s):  
Hiromichi HONGO ◽  
Masayoshi YAMAZAKI ◽  
Takashi WATANABE ◽  
Junichi KINUGAWA ◽  
Yoshio MONMA
Keyword(s):  
Stainless Steel ◽  
Creep Strain ◽  
Welded Joints ◽  
Strain Distribution ◽  
Creep Rupture ◽  
304 Stainless Steel ◽  
Thick Plates ◽  
Rupture Behavior

scholarly journals Residual Stresses Induced by Surface Working and Their Improvement by Emery Paper Polishing

2020 ◽  
Vol 4 (2) ◽  
pp. 21
Author(s):  
Makoto Hayashi
Keyword(s):  
Residual Stress ◽  
Stainless Steel ◽  
Fatigue Strength ◽  
Residual Stresses ◽  
Diffraction Method ◽  
304 Stainless Steel ◽  
Heat Treated ◽  
Emery Paper ◽  
Type 304 ◽  
Type 304 Stainless Steel

In many of machine parts and structural components, materials surface would be worked. In this study, residual stresses on the surfaces were measured by X-ray diffraction method, and effects of surface working on the residual stresses were examined. In case of lathe machining of type 304 stainless steel bar, the residual stresses in circumferential directions are tensile, and those in axial directions are almost compressive. Highly tensile residual stresses in the circumferential directions were improved by emery paper polishing. 10 to 20 times of polishing changes high tensile residual stresses to compressive residual stresses. In the case of shot peening on a type 304 stainless steel plate, the compressive residual stress inside is several hundred MPa lower than that on the surface. By applying the emery paper polishing to the shot peened surface 10 or 20 times, the residual stress on the surface is improved to −700 MPa. While fatigue strength at 288 °C in the air of the shot peened material is 30 MPa higher than solution heat treated and electro-polished material, the fatigue strength of the shot peened and followed by emery paper polished material is 60 MPa higher. Thus, the emery paper polishing is simple and a very effective process for improvement of the residual stresses.

Residual Stresses Prediction for CO2 Laser Butt-Welding of 304-Stainless Steel

2006 ◽  
Vol 3-4 ◽  
pp. 125-130 ◽  
Author(s):  
Khaled Y. Benyounis ◽  
Abdul Ghani Olabi ◽  
M.S.J. Hashmi
Keyword(s):  
Residual Stress ◽  
Stainless Steel ◽  
Residual Stresses ◽  
Laser Power ◽  
Travel Speed ◽  
304 Stainless Steel ◽  
Hole Drilling ◽  
Design Matrix ◽  
Butt Welding ◽  
Input Variables

Residual stresses are an integral part of the total stress acting on any component in service. It is important to determine and/or predict the magnitude, nature and direction of the residual stress to estimate the life of important engineering parts, particularly welded components. This work aims to introduce experimental models to predict residual stresses in the heat-affected zone (HAZ). These models specify the effect of laser welding input parameters on maximum residual stress and its direction. The process input variables considered in this study are laser power (1.03 - 1.368 kW), travel speed (26.48 – 68.52 cm/min) and focal point position (- 1 to 0 mm). Laser butt-welding of 304 stainless steel plates of 3 mm thick were investigated using a 1.5 kW CW CO2 Rofin laser as a welding source. Hole-drilling method was employed to measure the magnitude, and direction of the maximum principal stress in and around the HAZ, using a CEA-06- 062UM-120 strain gauge rosette, which allows measurement of the residual stresses close to the weld bead. The experiment was designed based on Response Surface Methodology (RSM). Fifteen different welding conditions plus 5 repeat tests were carried out based on the design matrix. Maximum principal residual stresses and their directions were calculated for the twenty samples. The stepwise regression method was selected using Design-expert software to fit the experimental responses to a second order polynomial. Sequential F test and other adequacy measures were then used to check the models adequacy. The experimental results indicate that the proposed mathematical models could adequately describe the residual stress within the limits of the factors being studied. Using the models developed, the main and interaction effect of the process input variables on the two responses were determined quantitatively and presented graphically. It is observed that the travel speed and laser power are the main factors affecting the behavior of the residual stress. It is recommended to use the models to find the optimal combination of welding conditions that lead to minimum distortion.

Effects of Laser Shock Processing on Corrosion Properties of 304 Stainless Steel

2010 ◽  
Vol 426-427 ◽  
pp. 109-113
Author(s):  
De Jun Kong ◽  
Hong Miao ◽  
A.P. Hu
Keyword(s):  
Aqueous Solution ◽  
Residual Stress ◽  
Stainless Steel ◽  
Stress Corrosion ◽  
Compressive Residual Stress ◽  
Hardened Layer ◽  
304 Stainless Steel ◽  
Laser Shock ◽  
Laser Shock Processing ◽  
Corrosion Properties

The surface of 304 stainless steel was processed by laser shock wave, its surface micro-structures were observed with SEM, and residual stresses on its surface were measured with X-ray diffraction (XRD) stress tester, and the production mechanism of residual stress was analyzed. The experiment of stress corrosion in 25% NaCl aqueous solution was finished, the crack sensitivity of stress corrosion in NaCl aqueous solution was researched, and the effects of LSP on stress corrosion resistance were analyzed. The results shown that the refined hardened-layer is acquired on the surface of 304 stainless steel by LSP, and compressive residual stress has greatly increased, which improve availably the performances of stress corrosion resistant. The time of appearing cracks is inverse ratio with compressive residual stress, and LSP decreases effectively its stress corrosion cracks.

Influence of Laser Parameters on Residual Stress Field of AISI 304 Stainless Steel Induced by Laser Peening: A Finite Element Analysis

2006 ◽  
Author(s):  
Xiang Ling ◽  
Weiwei Peng
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Stainless Steel ◽  
Stress Field ◽  
Stress Corrosion ◽  
Compressive Stress ◽  
304 Stainless Steel ◽  
Laser Peening ◽  
Aisi 304 Stainless Steel ◽  
Aisi 304

The present paper established a non-linear elastic-plastic finite element method to predict the residual compressive stress distribution induced by Laser Peening (LP) in the AISI 304 stainless steel. The two dimensional FEA model considered the dynamic material properties at high strain rate (106/s) and the evaluation of loading conditions. Effects of laser power density, laser spot size, laser pulse duration, multiple LP processes and one/two-sided peening on the compressive stress field in the stainless steel were evaluated for the purpose of optimizing the process. Numerical results have a good agreement with the measurement values by X-ray diffraction method and also show that the magnitude of compressive stress induced by laser peening is greater than the tensile welding residual stress. So, laser peening is an effective method for protecting weldments against stress corrosion crack. The above results provide the basis for studying the mechanism on prevention of stress corrosion cracking in weld joint of type 304 stainless steel by laser peening.

Sign in / Sign up

Export Citation Format

Share Document