Magnetic droplet actuation on natural (Colocasia leaf) and fluorinated silica nanoparticle superhydrophobic surfaces

2015 ◽  
Vol 220 ◽  
pp. 5-12 ◽  
Author(s):  
Lili Mats ◽  
Rachel Young ◽  
Graham T.T. Gibson ◽  
Richard D. Oleschuk
Coatings ◽  
2019 ◽  
Vol 9 (8) ◽  
pp. 472 ◽  
Author(s):  
Doeun Kim ◽  
Arun Sasidharanpillai ◽  
Ki Hoon Yun ◽  
Younki Lee ◽  
Dong-Jin Yun ◽  
...  

Robust superhydrophobic surfaces are fabricated on different substrates by a scalable spray coating process. The developed superhydrophobic surface consists of thin layers of surface functionalized silica nanoparticle (SiO2) bound to the substrate by acrylate-polyurethane (PU) binder. The influence of the SiO2/PU ratio on the superhydrophobicity, and the robustness of the developed surface, is systematically analyzed. The optimized SiO2/PU ratio for prepared superhydrophobic surfaces is obtained between 0.9 and 1.2. The mechanism which yields superhydrophobicity to the surface is deduced for the first time with the help of scanning electron microscopy and profilometer. The effect of mechanical abrasion on the surface roughness and superhydrophobicity are analyzed by using profilometer and contact angle measurement, respectively. Finally, it is concluded that the binder plays a key role in controlling the surface roughness and superhydrophobicity through the capillary mechanism. Additionally, the reason for the reduction in performance is also discussed with respect to the morphology variation.


2014 ◽  
Vol 2 (40) ◽  
pp. 17165-17173 ◽  
Author(s):  
Dae Ho Lee ◽  
Jin Jeong ◽  
Se Won Han ◽  
Dong Pil Kang

Superhydrophobic surfaces with near-zero sliding angles are generated by solvent ε-mediated silica particle aggregation and formation of multi-scale roughness.


Author(s):  
Christopher Swarctz ◽  
Elias Aljallis ◽  
Scott Hunter ◽  
John Simpson ◽  
Chang-Hwan Choi

In this study, a closed loop low-temperature wind tunnel was custom-built and uniquely used to investigate the anti-icing mechanism of superhydrophobic surfaces in regulated flow velocities, temperatures, humidity, and water moisture particle sizes. Silica nanoparticle-based hydrophobic coatings were tested as superhydrophobic surface models. During tests, images of ice formation were captured by a camera and used for analysis of ice morphology. Prior to and after wind tunnel testing, apparent contact angles of water sessile droplets on samples were measured by a contact angle meter to check degradation of surface superhydrophobicity. A simple peel test was also performed to estimate adhesion of ice on the surfaces. When compared to an untreated sample, superhydrophobic surfaces inhibited initial ice formation. After a period of time, random droplet strikes attached to the superhydrophobic surfaces and started to coalesce with previously deposited ice droplets. These sites appear as mounds of accreted ice across the surface. The appearance of the ice formations on the superhydrophobic samples is white rather than transparent, and is due to trapped air. These ice formations resemble soft rime ice rather than the transparent glaze ice seen on the untreated sample. Compared to untreated surfaces, the icing film formed on superhydrophobic surfaces was easy to peel off by shear flows.


2020 ◽  
Vol 16 (5) ◽  
pp. 748-756
Author(s):  
Mir Waqas Alam ◽  
Tentu Nageswara Rao ◽  
Yarasani Prashanthi ◽  
Vourse Sridhar ◽  
Adil Alshoaibi ◽  
...  

Background: Herbicides are very beneficial in the crop yield with the aid of controlling weeds within the agriculture, but several herbicides are chronic in soil. Objective: In this study, nanoparticles and the packages of synthesized novel silica nanoparticles were studied for the preconcentration of herbicides. Methods: These nanoparticles prepared by the Stöber mechanism were purified and functionalized. Nanoparticles thus prepared successfully were used as supporting material for the preconcentration of residues of herbicides in the water. Results: Preconcentration was achieved by preparing the silica-based solid-phase-extraction cartridges. Nanoparticles used for this purpose were within the range of 50-250 nm. An SPE cartridge was prepared by packing 200 mg of silica nanoparticle in the empty cartridge of diameter 5.5 cm and length 0.6 cm in between PTFE frits. Aqueous solutions of 0.1 μg/ml of herbicides were prepared separately, and 10 ml of the solution was passed through the cartridge at the rate of 0.2 ml/min. After passing 10 ml volume of the aqueous solution, residues adsorbed on the cartridge were eluted using 2 ml of acetonitrile. The eluate was injected to determine the herbicide residue adsorbed on the SPE cartridge. Conclusion: In the study, it was found that greater than 90% of the herbicide residues were trapped on silica nanoparticle-based SPE cartridge. An analytical method was developed for the simultaneous determination of these herbicides. The residues were quantified by LC-MS/MS with ESI mode.


Author(s):  
Kumar Nishchaya ◽  
Swatantra K.S. Kushwaha ◽  
Awani Kumar Rai

Background: Present malignant cancer medicines has the advancement of magnetic nanoparticles as delivery carriers to magnetically accumulate anticancer medication in malignant growth tissue. Aim: In the present investigation, a silica nanoparticles (MSNs) stacked with hydroxyurea were combined and was optimized for dependent and independent variables. Method: In this study, microporous silica nanoparticle stacked with neoplastic medication had been prepared through emulsification followed with solvent evaporation method. Prepared MSNs were optimized for dependent and independent variables. Different formulations were prepared with varying ratio of polymer, lipid and surfactant which affects drug release and kinetics of drug release pattern. The obtained MSNs were identified by FTIR, SEM, drug entrapment, in-vitro drug release, drug release kinetics study, stability testing in order to investigate the nanoparticle characteristics. Results: The percentage drug entrapment of the drug for the formulations F1, F2, F3, was found to be 27.78%, 65.52% and 48.26%. The average particle size for F2 formulation was found to be 520 nm through SEM. The cumulative drug release for the formulations F1, F2, F3 was found to be 64.17%, 71.82% and 32.68%. The formulations were found to be stable which gives controlled drug delivery for 6 hours. Conclusion: From the stability studies data it can be culminated that formulations are most stable when stored at lower temperature or in refrigerator i.e. 5˚C ± 3˚C. It can be concluded that MSN’s loaded with hydroxyurea is a promising approach towards the management of cancer due to its sustained release and less side effects.


2009 ◽  
pp. 5100 ◽  
Author(s):  
Juewen Liu ◽  
Alison Stace-Naughton ◽  
C. Jeffrey Brinker

Sign in / Sign up

Export Citation Format

Share Document