Zeroing in on the root cause of the clots in a blood bag: Reinforcing improvement in blood collection practices

Author(s):  
Manish Raturi ◽  
Ayushi Kediya ◽  
Mansi Kala ◽  
Adityaveer Sahrawat
2016 ◽  
Vol 10 (1) ◽  
pp. 3
Author(s):  
Shamee Shastry ◽  
Soumya Das

CJEM ◽  
2014 ◽  
Vol 16 (01) ◽  
pp. 20-24 ◽  
Author(s):  
Julian James Owen ◽  
Andrew Worster ◽  
Barbara Marie Waines ◽  
James Ward ◽  
Peter Kavsak ◽  
...  

ABSTRACTObjective:Emergency department (ED) patients with symptoms of cardiac ischemia often require a second cardiac troponin (cTn) measurement to rule out non–ST elevation myocardial infarction. We measured the total turnaround time and the component event times following the ordering of the second cTn level to ED discharge to identify root causes of delays.Methods:We reviewed a random sample of ED discharges following a second normal cTn measurement and recorded associated event times. The central tendency of time intervals is reported as median and mean number of minutes with interquartile ranges (IQRs) and 95% confidence intervals, respectively.Results:From 9,656 eligible cases, we randomly selected 226 for data collection. The median number of minutes for each event are as follows: from ordering the second cTn measurement to the time of ED discharge was 90 minutes (IQR 65–120); for blood collection from the time the collection was ordered for was 0 minutes (IQR 212–0); from blood collection to the time the blood was transported to the laboratory was 9 minutes (IQR 2–19); laboratory process duration was 44 minutes (IQR 39–52); from when the results were available to the time the patient was discharged was 30 minutes (IQR 15–52).Conclusions:For ED patients discharged following two normal cTn levels, the laboratory processing time and time from the result being available to the time of ED discharge represent the longest modifiable time periods to reduce ED length of stay.


Author(s):  
Chandra Bimantara Putra ◽  
Her Gumiwang Ariswati ◽  
Sumber Sumber ◽  
Muzni Zahar

A blood collection monitor is a device used to measure and shake the blood bag during a blood transfusion so that the blood in the bag does not clot and is mixed with anticoagulant fluid in the bag properly. This study aims to design an automatic blood collection and mixer for the transfusion blood system. The advantage of the proposed design is accompanied by a safety system in the form of a barrier indicator that is connected to an alarm. The alarm served to give a warning to blood donors if there is an obstacle or there is no increase in volume as much as 20ml for 1 minute as recommended by the world blood bank association. This device can work with three different sizes of blood bags. In this study, a loadcell sensor is used to detect the amount of blood fluid that enters the bag. Furthermore, then it is converted into milliliter volume. In order to collect the blood, a shaker is drove using a motor controlled by Arduino microcontroller. From the measurement, for the entire size of the blood bag, we found that the deviation is 0, UA is 0, and the average error is 0. Thus, it can be concluded that this device can be used properly. In the future, it can be developed a blood infusion with the flowrate measurement to determine the speed of blood during donation


Author(s):  
Martin J. Mahon ◽  
Patrick W. Keating ◽  
John T. McLaughlin

Coatings are applied to appliances, instruments and automobiles for a variety of reasons including corrosion protection and enhancement of market value. Automobile finishes are a highly complex blend of polymeric materials which have a definite impact on the eventual ability of a car to sell. Consumers report that the gloss of the finish is one of the major items they look for in an automobile.With the finish being such an important part of the automobile, there is a zero tolerance for paint defects by auto assembly plant management. Owing to the increased complexity of the paint matrix and its inability to be “forgiving” when foreign materials are introduced into a newly applied finish, the analysis of paint defects has taken on unparalleled importance. Scanning electron microscopy with its attendant x-ray analysis capability is the premier method of examining defects and attempting to identify their root cause.Defects are normally examined by cutting out a coupon sized portion of the autobody and viewing in an SEM at various angles.


2018 ◽  
Vol 88 (3-4) ◽  
pp. 151-157 ◽  
Author(s):  
Scott W. Leonard ◽  
Gerd Bobe ◽  
Maret G. Traber

Abstract. To determine optimal conditions for blood collection during clinical trials, where sample handling logistics might preclude prompt separation of erythrocytes from plasma, healthy subjects (n=8, 6 M/2F) were recruited and non-fasting blood samples were collected into tubes containing different anticoagulants (ethylenediaminetetra-acetic acid (EDTA), Li-heparin or Na-heparin). We hypothesized that heparin, but not EDTA, would effectively protect plasma tocopherols, ascorbic acid, and vitamin E catabolites (α- and γ-CEHC) from oxidative damage. To test this hypothesis, one set of tubes was processed immediately and plasma samples were stored at −80°C, while the other set was stored at 4°C and processed the following morning (~30 hours) and analyzed, or the samples were analyzed after 6 months of storage. Plasma ascorbic acid, as measured using HPLC with electrochemical detection (LC-ECD) decreased by 75% with overnight storage using EDTA as an anticoagulant, but was unchanged when heparin was used. Neither time prior to processing, nor anticoagulant, had any significant effects upon plasma α- or γ-tocopherols or α- or γ-CEHC concentrations. α- and γ-tocopherol concentrations remained unchanged after 6 months of storage at −80°C, when measured using either LC-ECD or LC/mass spectrometry. Thus, refrigeration of whole blood at 4°C overnight does not change plasma α- or γ-tocopherol concentrations or their catabolites. Ascorbic acid is unstable in whole blood when EDTA is used as an anticoagulant, but when whole blood is collected with heparin, it can be stored overnight and subsequently processed.


Crisis ◽  
2015 ◽  
Vol 36 (5) ◽  
pp. 316-324 ◽  
Author(s):  
Donna Gillies ◽  
David Chicop ◽  
Paul O'Halloran

Abstract. Background: The ability to predict imminent risk of suicide is limited, particularly among mental health clients. Root cause analysis (RCA) can be used by health services to identify service-wide approaches to suicide prevention. Aims: To (a) develop a standardized taxonomy for RCAs; (b) to quantitate service-related factors associated with suicides; and (c) to identify service-related suicide prevention strategies. Method: The RCAs of all people who died by suicide within 1 week of contact with the mental health service over 5 years were thematically analyzed using a data collection tool. Results: Data were derived from RCAs of all 64 people who died by suicide between 2008 and 2012. Major themes were categorized as individual, situational, and care-related factors. The most common factor was that clients had recently denied suicidality. Reliance on carers, recent changes in medication, communication problems, and problems in follow-through were also commonly identified. Conclusion: Given the difficulty in predicting suicide in people whose expressions of suicidal ideation change so rapidly, services may consider the use of strategies aimed at improving the individual, stressor, support, and care factors identified in this study.


Sign in / Sign up

Export Citation Format

Share Document