The effect of volume fraction of WC particles on erosion resistance of WC reinforced iron matrix surface composites

Wear ◽  
2003 ◽  
Vol 255 (1-6) ◽  
pp. 134-138 ◽  
Author(s):  
Rong Zhou ◽  
Yehua Jiang ◽  
Dehong Lu
Keyword(s):  
Erosion Resistance ◽  
Volume Fraction ◽  
Iron Matrix ◽  
Surface Composites ◽  
Matrix Surface

Growth Kinetics of In Situ Preparation of Dense TiC Ceramic Layer-Reinforced Gray Cast Iron Matrix Surface Composites

2015 ◽  
Vol 17 (11) ◽  
pp. 1562-1567 ◽  
Author(s):  
Shaozhong Fan ◽  
Lisheng Zhong ◽  
Yunhua Xu ◽  
Yonghong Fu ◽  
Liangliang Wang
Keyword(s):  
Cast Iron ◽  
Growth Kinetics ◽  
Gray Cast Iron ◽  
Ceramic Layer ◽  
Iron Matrix ◽  
In Situ Preparation ◽  
Surface Composites ◽  
Matrix Surface ◽  
Kinetics Of

Study on TaC Reinforced Iron Matrix Surface Gradient Composites Produced In Situ

2016 ◽  
Vol 848 ◽  
pp. 38-42 ◽  
Author(s):  
Na Na Zhao ◽  
Yun Hua Xu ◽  
Ke Song ◽  
Liu Liu Shen ◽  
V.E. Ovcharenko
Keyword(s):  
Volume Fraction ◽  
Tantalum Carbide ◽  
Ceramic Layer ◽  
Wear Testing ◽  
Micro Hardness ◽  
Iron Matrix ◽  
Surface Gradient ◽  
Matrix Surface ◽  
Dense Ceramic

Tantalum carbide (TaC) gradient composites were fabricated via in-situ fabrication method from the tantalum plate and gray cast iron. The morphology, phase constituents, micro-hardness, and relative abrasion resistance of the composites were analyzed by scanning electron microscopy (SEM), X-ray diffraction (XRD), micro-hardness tester and abrasive wear testing machine. The surface layer, which was ~160μm thick, was dense ceramic layer composed by ~90% submicron TaC particulates. The highest micro-hardness value of the dense ceramic layer was 13.84 GPa. In the sub-layer, the gradient distribution of TaC particulates reflected in the volume fraction decreased from 90% to 0%. While the micro-hardness value decreased from 10.81 GPa to 4.10 GPa. The metallurgical combination of the interface between the composites and matrix was perfect. The wear resistance of TaC reinforced iron matrix surface gradient composites increased significantly.

In Situ Production of Fe-TiC Surface Composite

2011 ◽  
Vol 335-336 ◽  
pp. 80-85 ◽  
Author(s):  
Jing Wang ◽  
Yi Chao Ding ◽  
Hong Cheng ◽  
Yi San Wang
Keyword(s):  
Wear Resistance ◽  
Oxidation Resistance ◽  
Volume Fraction ◽  
Gray Iron ◽  
Iron Matrix ◽  
Good Oxidation Resistance ◽  
Surface Composite ◽  
Matrix Surface ◽  
Tic Particulates

TiC particulates reinforced iron matrix surface composite was produced by cast technique and in-situ synthesis technique. The surface composite was investigated from thermodynamics, microstructure, wear-resistance and oxidation-resistance. The results show TiC particles whose volume fraction is about 40% exhibit fine size in iron matrix on the surface composite. An excellent metallurgy-bond is observed between the surface composite and the gray iron. Fe-TiC surface composite shows good oxidation-resistance at 900°C and great wear-resistance under condition of dry sliding.

Effect of Cr addition on the microstructure and abrasive wear resistance of WC-reinforced iron matrix surface composites

2014 ◽  
Vol 29 (6) ◽  
pp. 778-785 ◽  
Author(s):  
Zulai Li ◽  
Yehua Jiang ◽  
Rong Zhou ◽  
Zhihui Chen ◽  
Quan Shan ◽  
...  
Keyword(s):  
Wear Resistance ◽  
Abrasive Wear ◽  
Abrasive Wear Resistance ◽  
Iron Matrix ◽  
Surface Composites ◽  
Matrix Surface ◽  
Cr Addition ◽  
Image Position

Abstract

scholarly journals Microstructure and wear characteristics of ATZ ceramic particle reinforced gray iron matrix surface composites

China Foundry ◽  
2018 ◽  
Vol 15 (3) ◽  
pp. 167-172 ◽  
Author(s):  
Xue Ma ◽  
Liang-feng Li ◽  
Fan Zhang ◽  
Zu-hua Zhang ◽  
Hao Wang ◽  
...  
Keyword(s):  
Ceramic Particle ◽  
Gray Iron ◽  
Iron Matrix ◽  
Wear Characteristics ◽  
Surface Composites ◽  
Matrix Surface

General Process for In Situ Formation of Iron-Matrix Surface Composites Reinforced by Carbide Ceramic

2016 ◽  
Vol 852 ◽  
pp. 467-471
Author(s):  
Xi Zhang ◽  
Li Sheng Zhong ◽  
Na Na Zhao ◽  
Vladimir E. Ovcharenko ◽  
Hong Wu ◽  
...  
Keyword(s):  
Ductile Cast Iron ◽  
Synthesis Process ◽  
Iron Matrix ◽  
General Process ◽  
Ceramic Particles ◽  
Surface Composites ◽  
Matrix Surface ◽  
Wide Range ◽  
Particulate Reinforced

Ceramic particles with high hardness and thermal stability can be used to fabricate in situ carbide particulate-reinforced iron-matrix surface composites with high macro-hardness while retaining high toughness. This paper describes a general process by which in situ carbide particulate-reinforced iron-matrix surface composites with hard ceramic particles are readily formed by a novel in situ synthesis process that combines an infiltration casting process with subsequent heat treatment. The basis of our approach is integrating selected plates of different alloys that can form carbide easily into a metal matrix with a certain amount of carbon such as gray or ductile cast iron by casting to form alloy plates reinforced iron-matrix surface composites. Subsequent thermal treatment of resulting composites leads to alloy elements of plate reacting to the carbon in the matrix to form carbide particles. This approach is applicable to a wide range of materials and morphologies, and can be used in composites and machining tools, as well as in the wear-resistant component industry.

Sign in / Sign up

Export Citation Format

Share Document