On vortex formation from a cylinder. Part 1. The initial instability

1988 ◽  
Vol 190 ◽  
pp. 491-512 ◽  
Author(s):  
M. F. Unal ◽  
D. Rockwell
Keyword(s):  
Reynolds Number ◽  
Kinetic Energy ◽  
Circular Cylinder ◽  
Shear Layer ◽  
Vortex Shedding ◽  
Vortex Formation ◽  
Absolute Instability ◽  
Near Wake ◽  
Lower Range ◽  
Fluctuation Amplitude

Vortex shedding from a circular cylinder is examined over a tenfold range of Reynolds number, 440 ≤ Re ≤ 5040. The shear layer separating from the cylinder shows, to varying degrees, an exponential variation of fluctuating kinetic energy with distance downstream of the cylinder. The characteristics of this unsteady shear layer are interpreted within the context of an absolute instability of the near wake. At the trailing-end of the cylinder, the fluctuation amplitude of the instability correlates well with previously measured values of mean base pressure. Moreover, this amplitude follows the visualized vortex formation length as Reynolds number varies. There is a drastic decrease in this near-wake fluctuation amplitude in the lower range of Reynolds number and a rapid increase at higher Reynolds number. These trends are addressed relative to the present, as well as previous, observations.

High Frequency Characteristics of the Near Wake and Vortex Past a Triangular Cylinder

2020 ◽  
Vol 143 (3) ◽  
Author(s):  
Lei Sun ◽  
Yong Huang ◽  
Xiwei Wang ◽  
Xiang Feng ◽  
Wei Xiao
Keyword(s):  
Reynolds Number ◽  
Circular Cylinder ◽  
Vortex Core ◽  
High Frequency ◽  
Vortex Formation ◽  
Flame Stabilization ◽  
Near Wake ◽  
Freestream Velocity ◽  
Formation Region ◽  
Flow Past

Abstract The flow past a triangular cylinder is one of the fundamental flows and widely utilized in flame stabilization and heat transfer. In this study, the near wake and vortex characteristics of the flow past an equilateral triangular cylinder are experimentally measured by a high frequency particle image velocimetry (PIV) system at 3 kHz. The triangular cylinder is installed in a wind tunnel with Reynolds numbers ranging from 10,700 to 17,700. The Reynolds-averaged and phase-averaged methods are utilized to analyze the flow field. Based on the flow fields, the length of the vortex formation region is about 1.5 times of the length of the equilateral triangle side. The residence time of a vortex in the vortex formation region is equal to a vortex shedding period. The stream wise velocity of the vortex core center downstream the vortex formation is about 0.8 times of the freestream velocity, which is slightly larger than the value about 0.7 for the flow past a circular cylinder at the same Reynolds number. The maximum tangential velocity at the periphery of the vortex core maybe occurs slightly in advance of the vortex reaching the boundary of the vortex formation region. The normalized lengths of the recirculation zone of the triangular cylinder keep nearly unchanged and are about 1.55 to 1.9 times of those of the circular cylinder at the same Reynolds number. The normalized normal wise instead of stream wise turbulence intensity has stronger effects on the distribution of the normalized turbulent kinetic energy.

Symmetric Vortex Shedding From a Circular Cylinder Under Periodic Flow Forcing

2006 ◽  
Author(s):  
E. Konstantinidis ◽  
S. Balabani
Keyword(s):  
Circular Cylinder ◽  
Vortex Shedding ◽  
Vortex Formation ◽  
Excitation Frequency ◽  
Symmetric Mode ◽  
Near Wake ◽  
Wake Field ◽  
Vortex Pairs ◽  
Probabilistic Function ◽  
Number Of Cycles

This paper describes an experimental study of the near wake of a circular cylinder subjected to streamwise flow forcing. The wake field is examined by PIV and LDV for excitation frequencies in which symmetric shedding is likely. The results show that symmetric formation of vortex pairs occurs close to the cylinder synchronized with the oscillatory component of the flow. The symmetric mode rapidly breaks down and gives rise to an antisymmetric arrangement of single vortices further downstream. The number of cycles for which the symmetrical vortices persist in the near wake is a probabilistic function of the excitation frequency and forcing amplitude. Details of the related wake kinematics and frequencies are shown and the findings are discussed in relation to symmetric vortex formation occurring in self-excited streamwise oscillations.

Large eddy simulation of flow over a twisted cylinder at a subcritical Reynolds number

2014 ◽  
Vol 759 ◽  
pp. 579-611 ◽  
Author(s):  
Jae Hwan Jung ◽  
Hyun Sik Yoon
Keyword(s):  
Reynolds Number ◽  
Large Eddy Simulation ◽  
Shear Layer ◽  
Vortex Shedding ◽  
Vortex Formation ◽  
The Body ◽  
Recirculation Region ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Drag And Lift

AbstractWe consider a twisted cylinder that was designed by rotating the elliptic cross-section along the spanwise direction, resulting in a passive control. The flow over the twisted cylinder is investigated at a subcritical Reynolds number (Re) of 3000 using large eddy simulation based on the finite volume method. For comparison, the flow past smooth and wavy cylinders is also calculated. The twisted cylinder achieves reductions of approximately 13 and 5 % in mean drag compared with smooth and wavy cylinders, respectively. In particular, the root mean square (r.m.s.) value of the lift fluctuation of the twisted cylinder shows a substantial decrease of approximately 96 % compared with the smooth cylinder. The shear layer of the twisted cylinder covering the recirculation region is more elongated than those of the smooth and wavy cylinders, and vortex shedding from the twisted cylinder is considerably suppressed. Consequently, the elongation of the shear layer from the body and the near disappearance of vortex shedding in the near wake with weak vortical strength contributes directly to the reduction of drag and lift oscillation. Various fundamental mechanisms that affect the flow phenomena, three-dimensional separation, pressure coefficient, vortex formation length and turbulent kinetic energy are examined systematically to demonstrate the effect of the twisted cylinder surface. In addition, for the twisted cylinder at $\mathit{Re}=3000$, the effect of the cross-sectional aspect ratio is investigated from 1.25 to 2.25 to find an optimal value that can reduce the drag and lift forces. Moreover, the effect of the Reynolds number on the aerodynamic characteristics is investigated in the range of $3\times 10^{3}\leqslant \mathit{Re}\leqslant 1\times 10^{4}$. We find that as Re increases, the mean drag and the r.m.s. lift coefficient of the twisted cylinder increase, and the vortex formation length decreases.

scholarly journals The Effect of Slat Opening on Vortex Shedding Behind a Circular Cylinder

2019 ◽  
Vol 8 (4) ◽  
pp. 6879-6885
Keyword(s):  
Reynolds Number ◽  
Circular Cylinder ◽  
Governing Equation ◽  
Vortex Shedding ◽  
Vortex Formation ◽  
Bluff Bodies ◽  
Vortex Induced Vibrations ◽  
Better Than ◽  
Laminar Model

Add-on devices are widely used as one of the means of suppressing vortex induced vibrations from bluff bodies. The present study numerically investigates flow over a circular cylinder attached by an axial slat. The axial slat were of uniform and non-uniform openings of 67% and 44% porosity. The governing equation was solved using viscous-laminar model at Reynolds number, Re=300. It was found that the presence of the axial slats significantly suppressed vortex shedding behind the circular cylinder. The non-uniform slats showed longer vortex formation length with lower drag, in comparison to that of the uniform slats. In addition, the slats with 67% porosity of both uniform and non-uniform openings suppressed vortex better than that of 44% porosity slats, indicated by the longer vortex formation length and weaker intensity of vortices.

On vortex formation from a cylinder. Part 2. Control by splitter-plate interference

1988 ◽  
Vol 190 ◽  
pp. 513-529 ◽  
Author(s):  
M. F. Unal ◽  
D. Rockwell
Keyword(s):  
Reynolds Number ◽  
Large Scale ◽  
Vortex Formation ◽  
Effective Control ◽  
Absolute Instability ◽  
Near Wake ◽  
Number Range ◽  
Large Scale Vortex ◽  
The Absolute ◽  
Substantial Control

Control of vortex formation from a circular cylinder by a long plate in its wake is examined over the Reynolds number range 140 < Re < 3600. There are two basic flow regimes: a pre-vortex formation regime, in which the plate precludes formation of a large-scale vortex upstream of the tip of the plate; and a post-vortex formation regime in which one or more large-scale vortices are formed upstream of the edge. The unsteady pressure loading at the tip of the plate increases by over an order of magnitude during transition from the pre- to post-vortex formation regime. If the plate is located near the cylinder, it is possible to more than double the vortex formation length, relative to the case of the free wake. Moreover, these observations suggest that: there is a minimum streamwise lengthscale for development of the absolute instability of the near wake and thereby the large-scale vortex; and the vortex formation length may also be influenced by the downstream vorticity dynamics. When the plate is located downstream of the initially formed vortex, effective control is possible when the near-wake fluctuation level and mean base pressure of the corresponding free (non-impinging) wake are sufficiently small. This occurs in the low and moderate subcritical regimes; the substantial control by the wake-plate interaction in this range of Reynolds number implies low strength of the absolute instability of the near wake. However, in the pure von Kármán regime, selfcontrol of the near wake dominates that imposed by the wake-edge interaction, suggesting a strong absolute instability of the near wake.

Turbulent wake behind a curved circular cylinder

2014 ◽  
Vol 742 ◽  
pp. 192-229 ◽  
Author(s):  
José P. Gallardo ◽  
Helge I. Andersson ◽  
Bjørnar Pettersen
Keyword(s):  
Reynolds Number ◽  
Circular Cylinder ◽  
Vortex Shedding ◽  
Bluff Body ◽  
Vortex Formation ◽  
Axial Flow ◽  
Turbulent Wake ◽  
Outer Face ◽  
Wake Region ◽  
Axial Curvature

AbstractThis paper reports results from a direct numerical simulation of the flow past a circular cylinder with axial curvature. The main objective is to explore the effects of spanwise curvature on the stability of the shear layers and the turbulent wake at the subcritical Reynolds number of 3900. The bluff-body geometry is adapted from a previous study conducted at lower Reynolds numbers, in which a quarter segment of a ring represented the deformed cylinder. A convex configuration in which the free-stream direction is towards the outer face of the ring is adopted here. The present results show a striking distinction between the upper and lower wake regions. Despite the turbulent character of the wake, the upper wake region is more coherent due to the periodic vortex shedding of primary vortical structures, which are in close alignment with the axial curvature. A mild axial flow develops upwards along the lee face of the curved cylinder, displacing the vortex formation region further downstream from the location expected for a straight cylinder at the same Reynolds number. In the lower wake region the vortex shedding strength is drastically reduced due to larger local inclination, resulting in higher three-dimensionality and loss of coherence. A strong downdraft with a swirling pattern is the dominating feature in the lower base region. This is associated with a substantial decrease of the base suction, and the suppression of the characteristic recirculating backflow.

Vortex shedding from a circular cylinder in moderate-Reynolds-number shear flow

1980 ◽  
Vol 101 (4) ◽  
pp. 721-735 ◽  
Author(s):  
Masaru Kiya ◽  
Hisataka Tamura ◽  
Mikio Arie
Keyword(s):  
Reynolds Number ◽  
Circular Cylinder ◽  
Shear Flow ◽  
Vortex Shedding ◽  
Transverse Velocity ◽  
Number Range ◽  
Uniform Shear ◽  
Reynolds Number Range ◽  
Moderate Reynolds Number ◽  
Shear Parameter

The frequency of vortex shedding from a circular cylinder in a uniform shear flow and the flow patterns around it were experimentally investigated. The Reynolds number Re, which was defined in terms of the cylinder diameter and the approaching velocity at its centre, ranged from 35 to 1500. The shear parameter, which is the transverse velocity gradient of the shear flow non-dimensionalized by the above two quantities, was varied from 0 to 0·25. The critical Reynolds number beyond which vortex shedding from the cylinder occurred was found to be higher than that for a uniform stream and increased approximately linearly with increasing shear parameter when it was larger than about 0·06. In the Reynolds-number range 43 < Re < 220, the vortex shedding disappeared for sufficiently large shear parameters. Moreover, in the Reynolds-number range 100 < Re < 1000, the Strouhal number increased as the shear parameter increased beyond about 0·1.

scholarly journals Effect of Cylinder Gap Ratio on The Wake of a Circular Cylinder Enclosed by Various Perforated Shrouds

CFD letters ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 51-68
Author(s):  
Nurul Azihan Ramli ◽  
Azlin Mohd Azmi ◽  
Ahmad Hussein Abdul Hamid ◽  
Zainal Abidin Kamarul Baharin ◽  
Tongming Zhou
Keyword(s):  
Reynolds Number ◽  
Circular Cylinder ◽  
Vortex Shedding ◽  
Control Method ◽  
Lift Coefficient ◽  
Base Case ◽  
Bluff Bodies ◽  
Ansys Fluent ◽  
Gap Ratio ◽  
Spacing Ratio

Flow over bluff bodies produces vortex shedding in their wake regions, leading to structural failure from the flow-induced forces. In this study, a passive flow control method was explored to suppress the vortex shedding from a circular cylinder that causes many problems in engineering applications. Perforated shrouds were used to control the vortex shedding of a circular cylinder at Reynolds number, Re = 200. The shrouds were of non-uniform and uniform holes with 67% porosity. The spacing gap ratio between the shroud and the cylinder was set at 1.2, 1.5, 2, and 2.2. The analysis was conducted using ANSYS Fluent using a viscous laminar model. The outcomes of the simulation of the base case were validated with existing studies. The drag coefficient, Cd, lift coefficient, Cl and the Strouhal number, St, as well as vorticity contours, velocity contours, and pressure contours were examined. Vortex shedding behind the shrouded cylinders was observed to be suppressed and delayed farther downstream with increasing gap ratio. The effect was significant for spacing ratio greater than 2.0. The effect of hole types: uniform and non-uniform holes, was also effective at these spacing ratios for the chosen Reynolds number of 200. Specifically, a spacing ratio of 1.2 enhanced further the vortex intensity and should be avoided.

Laminar Forced Convection From a Circular Cylinder Placed in a Micropolar Fluid

2006 ◽  
Vol 129 (3) ◽  
pp. 256-264 ◽  
Author(s):  
F. M. Mahfouz
Keyword(s):  
Reynolds Number ◽  
Circular Cylinder ◽  
Prandtl Number ◽  
Drag Coefficient ◽  
Forced Convection ◽  
Vortex Shedding ◽  
Micropolar Fluid ◽  
Clear Trend ◽  
Thermal Fields ◽  
Laminar Forced Convection

In this paper laminar forced convection associated with the cross-flow of micropolar fluid over a horizontal heated circular cylinder is investigated. The conservation equations of mass, linear momentum, angular momentum and energy are solved to give the details of flow and thermal fields. The flow and thermal fields are mainly influenced by Reynolds number, Prandtl number and material parameters of micropolar fluid. The Reynolds number is considered up to 200 while the Prandtl number is fixed at 0.7. The dimensionless vortex viscosity is the only material parameter considered in this study and is selected in the range from 0 to 5. The study has shown that generally the mean heat transfer decreases as the vortex viscosity increases. The results have also shown that both the natural frequency of vortex shedding and the amplitude of oscillating lift force experience clear reduction as the vortex viscosity increases. Moreover, the study showed that there is a threshold value for vortex viscosity above which the flow over the cylinder never responds to perturbation and stays symmetric without vortex shedding. Regarding drag coefficient, the results have revealed that within the selected range of controlling parameters the drag coefficient does not show a clear trend as the vortex viscosity increases.

Sign in / Sign up

Export Citation Format

Share Document