On the steady separated flow around an inclined flat plate

1997 ◽  
Vol 333 ◽  
pp. 403-413 ◽  
Author(s):  
W. W. H. YEUNG ◽  
G. V. PARKINSON
Keyword(s):  
Flat Plate ◽  
Bluff Body ◽  
Separation Bubble ◽  
Separated Flow ◽  
Leading Edge ◽  
Source Model ◽  
Pressure Distributions ◽  
Wide Range ◽  
Trailing Edges ◽  
Edge Separation

An inviscid analytic model is proposed for the steady separated flow around an inclined flat plate. With the plate normal to the stream, the model reduces to the wake-source model of Parkinson & Jandali originally developed for flow external to a symmetrical two-dimensional bluff body and its wake. At any other inclination, the Kutta condition is satisfied at both leading and trailing edges of the plate, and, in the limit that the angle of attack approaches zero, classical airfoil theory is recovered. A boundary condition is formulated based on some experimental results of Abernathy, but no additional empirical information is required. The predicted pressure distributions on the wetted surface for a wide range of angle attack are found to be in good agreement with experimental data, especially at smaller angles of attack. An extension to include a leading-edge separation bubble is explored and results are satisfactory.

On the Response of a Strongly Diffusing Flow to Propagating Wakes

2009 ◽  
Vol 131 (2) ◽  
Author(s):  
J. P. Gostelow ◽  
R. L. Thomas ◽  
D. S. Adebayo
Keyword(s):  
Flat Plate ◽  
Large Scale ◽  
Separation Bubble ◽  
Leading Edge ◽  
Adverse Pressure Gradient ◽  
Turbulent Spots ◽  
Stall Margin ◽  
Transverse Jet ◽  
Wide Range ◽  
Calming Effect

Further evidence on the similarities between transition and separation phenomena occurring in turbomachinery and wind tunnel flows is provided by measurements on a large scale flat plate under a strong adverse pressure gradient. The flat plate has a long laminar separation bubble and is subjected to a range of disturbances with triggering caused by injection of a transverse jet and subsequently by wakes generated by rods moving transversely upstream of the leading edge. Wakes were originally presented individually. Each individual wake provoked a vigorous turbulent patch, resulting in the instantaneous collapse of the separation bubble. This was followed by a very strong, and stable, calmed region. Following the lead given by the experiments of Gutmark and Blackwelder (1987, “On the Structure of Turbulent Spot in a Heated Laminar Boundary Layer,” Exp. Fluids, 5, pp. 207–229.) on triggered turbulent spots, wakes were then presented in pairs at different wake spacing intervals. In this way wake interaction effects could be investigated in more detail. As in the work on triggered turbulent spots the spacing between impinging wakes was systematically varied; it was found that for close wake spacings the calmed region acted to suppress the turbulence in the following turbulent patch. To investigate whether this phenomenon was a recurring one or whether the flow then reverted back to its unperturbed state, the experiments were repeated with three and four rods instead of two. This has the potential for making available a wide range of variables including direction and speed of rod rotation. It was found that the subsequent wakes were also suppressed by the calming effect. It may be anticipated that this repeating situation is present in a turbomachine, resulting in hidden benefits for blade count and efficiency. There may also conceivably be blade loading advantages while retaining favorable heat transfer conditions in high pressure turbines or stall margin in axial compressors. The inherent and prospective benefits of the calming effect therefore need to be understood thoroughly and new opportunities exploited where this is feasible.a

A theoretical investigation of enhanced lift in the presence of thin aerofoil stall

1999 ◽  
Vol 103 (1023) ◽  
pp. 237-244 ◽  
Author(s):  
W. W. H. Yeung ◽  
G. V. Parkinson
Keyword(s):  
Flat Plate ◽  
Flow Model ◽  
Separated Flow ◽  
Leading Edge ◽  
Geometrical Parameters ◽  
Separation Flow ◽  
Attached Flow ◽  
Positive Angle ◽  
Edge Separation ◽  
Potential Flow Model

Abstract A theoretical study is presented for the investigation of a potential-flow model for enhancing lift over a flat-plate aerofoil experiencing thin aerofoil stall. Rather than suppressing the leading-edge separation, flow is assumed to separate tangentially at the leading edge and made to reattach smoothly at the tip of a forward-facing fence joining the plate tangentially on its upper surface to avoid any unnecessary stagnated flow. The length of the fence and its location from the leading edge form two geometrical parameters. At any positive angle of attack, the resulting bounding streamline emanating from the leading edge and terminating at the tip of the fence is simulated by using suitable mathematical singularities subject to boundary conditions such as attaining a finite velocity at each critical point of the conformal mapping involved, and the condition of finite pressure gradient at reattachment, when applicable. Computational results from varying these two geometrical parameters indicate that the lift from each model is enhanced, as compared with the attached flow model around a simple flat plate and the original separated flow model by Kirchhoff.

Scaling Parameters for a Time-Averaged Separation Bubble

1982 ◽  
Vol 104 (2) ◽  
pp. 178-184 ◽  
Author(s):  
A. J. Smits
Keyword(s):  
Bluff Body ◽  
Separation Bubble ◽  
Pressure Coefficient ◽  
Separated Flow ◽  
The Body ◽  
Splitter Plate ◽  
Universal Curve ◽  
Wide Range ◽  
Scaling Parameters ◽  
The Relationship

A splitter plate is placed in the wake of a two-dimensional bluff body. The splitter plate is long enough for the separated flow behind the body to reattach on the splitter plate. The time-averaged properties of this “closed” separation bubble are investigated under a wide range of kinematic conditions. It is found that blockage reduces the base pressure coefficient (Cpb) and the distance to reattachment (l) but the relationship between l and Cpb is not obvious. The pressure distribution in the separated zone, scaled on Cpb and l, can be described by a universal curve. The usefulness of a slotted wall in reducing blockage effects on bluff body flows is shown to be limited in that the wall porosity affects only some properties of the separation bubble.

On the Response of a Strongly Diffusing Flow to Propagating Wakes

2007 ◽  
Author(s):  
J. P. Gostelow ◽  
R. L. Thomas ◽  
D. S. Adebayo
Keyword(s):  
Flat Plate ◽  
Large Scale ◽  
Separation Bubble ◽  
Leading Edge ◽  
Adverse Pressure Gradient ◽  
Turbulent Spots ◽  
Stall Margin ◽  
Transverse Jet ◽  
Wide Range ◽  
Calming Effect

Further evidence on the similarities between transition and separation phenomena occurring in turbomachinery and wind tunnel flows is provided by measurements on a large scale flat plate under a strong adverse pressure gradient. The flat plate has a long laminar separation bubble and is subjected to a range of disturbances with triggering caused by injection of a transverse jet and subsequently by wakes generated by rods moving transversely upstream of the leading edge. Wakes were originally presented individually. Each individual wake provoked a vigorous turbulent patch, resulting in the instantaneous collapse of the separation bubble. This was followed by a very strong, and stable, calmed region. Following the lead given by the experiments of Gutmark and Blackwelder on triggered turbulent spots, wakes were then presented in pairs at different wake spacing intervals. In this way wake interaction effects could be investigated in more detail. As in the work on triggered turbulent spots the spacing between impinging wakes was systematically varied; it was found that for close wake spacings the calmed region acted to suppress the turbulence in the following turbulent patch. To investigate whether this phenomenon was a recurring one, or whether the flow then reverted back to its unperturbed state, the experiments were repeated with three and four rods instead of two. This has the potential for making available a wide range of variables including direction and speed of rod rotation. It was found that the subsequent wakes were also suppressed by the calming effect. It may be anticipated that this repeating situation is present in a turbomachine, resulting in hidden benefits for blade count and efficiency. There may also conceivably be blade loading advantages whilst retaining favorable heat transfer conditions in high pressure turbines or stall margin in axial compressors. The inherent and prospective benefits of the calming effect therefore need to be understood thoroughly and new opportunities exploited where this is feasible.

Characteristics of a separated flow past a semicircular leading-edge airfoil model under different imposed pressure gradient

2021 ◽  
pp. 095441002110212
Author(s):  
K Anand ◽  
KT Ganesh
Keyword(s):  
Boundary Layer ◽  
Particle Image Velocimetry ◽  
Pressure Gradient ◽  
Particle Image ◽  
Separation Bubble ◽  
Separated Flow ◽  
Leading Edge ◽  
Field Measurements ◽  
Bench Mark ◽  
Image Velocimetry

The effect of pressure gradient on a separated boundary layer past the leading edge of an airfoil model is studied experimentally using electronically scanned pressure (ESP) and particle image velocimetry (PIV) for a Reynolds number ( Re) of 25,000, based on leading-edge diameter ( D). The features of the boundary layer in the region of separation and its development past the reattachment location are examined for three cases of β (−30°, 0°, and +30°). The bubble parameters such as the onset of separation and transition and the reattachment location are identified from the averaged data obtained from pressure and velocity measurements. Surface pressure measurements obtained from ESP show a surge in wall static pressure for β = −30° (flap deflected up), while it goes down for β = +30° (flap deflected down) compared to the fundamental case, β = 0°. Particle image velocimetry results show that the roll up of the shear layer past the onset of separation is early for β = +30°, owing to higher amplification of background disturbances compared to β = 0° and −30°. Downstream to transition location, the instantaneous field measurements reveal a stretched, disoriented, and at instances bigger vortices for β = +30°, whereas a regular, periodically shed vortices, keeping their identity past the reattachment location, is observed for β = 0° and −30°. Above all, this study presents a new insight on the features of a separation bubble receiving a disturbance from the downstream end of the model, and these results may serve as a bench mark for future studies over an airfoil under similar environment.

Three-Dimensional and Rotational Aerodynamics on the NREL Phase VI Wind Turbine Blade

2008 ◽  
Vol 130 (3) ◽  
Author(s):  
Alvaro Gonzalez ◽  
Xabier Munduate
Keyword(s):  
Wind Turbine ◽  
Turbine Blade ◽  
Three Dimensional ◽  
Separated Flow ◽  
Leading Edge ◽  
Wind Turbine Blade ◽  
Trailing Edge ◽  
Rotating Blade ◽  
Nrel Phase Vi ◽  
Edge Separation

This work undertakes an aerodynamic analysis over the parked and the rotating NREL Phase VI wind turbine blade. The experimental sequences from NASA Ames wind tunnel selected for this study respond to the parked blade and the rotating configuration, both for the upwind, two-bladed wind turbine operating at nonyawed conditions. The objective is to bring some light into the nature of the flow field and especially the type of stall behavior observed when 2D aerofoil steady measurements are compared to the parked blade and the latter to the rotating one. From averaged pressure coefficients together with their standard deviation values, trailing and leading edge separated flow regions have been found, with the limitations of the repeatability of the flow encountered on the blade. Results for the parked blade show the progressive delay from tip to root of the trailing edge separation process, with respect to the 2D profile, and also reveal a local region of leading edge separated flow or bubble at the inner, 30% and 47% of the blade. For the rotating blade, results at inboard 30% and 47% stations show a dramatic suppression of the trailing edge separation, and the development of a leading edge separation structure connected with the extra lift.

Aerodynamic Measurements on the Interaction of Secondary Jets and Separation Bubble

2012 ◽  
Author(s):  
A. Samson ◽  
S. Sarkar
Keyword(s):  
Flat Plate ◽  
Large Scale ◽  
Separation Bubble ◽  
Three Dimensional ◽  
Leading Edge ◽  
Bubble Interactions ◽  
Separated Shear Layer ◽  
Bubble Length ◽  
Flow Visualizations ◽  
Turbulence Generation

The dynamics of separation bubble under the influence of continuous jets ejected near the semi-circular leading edge of a flat plate is presented. Two different streamwise injection angles 30° and 60° and velocity ratios 0.5 and 1 for Re = 25000 and 55000 (based on the leading-edge diameter) are considered here. The flow visualizations illustrating jet and separated layer interactions have been carried out with PIV. The objective of this study is to understand the mutual interactions of separation bubble and the injected jets. It is observed that flow separates at the blending point of semi-circular arc and flat plate. The separated shear layer is laminar up to 20% of separation length after which perturbations are amplified and grows in the second-half of the bubble leading to breakdown and reattachment. Blowing has significantly affected the bubble length and thus, turbulence generation. Instantaneous flow visualizations supports the unsteadiness and development of three-dimensional motions leading to formation of Kelvin-Helmholtz rolls and shedding of large-scale vortices due to jet and bubble interactions. In turn, it has been seen that both the spanwise and streamwise dilution of injected air is highly influenced by the separation bubble.

Flow Visualization Experiments on Tethered Flying Green Lacewings Chrysopa Dasyptera

1992 ◽  
Vol 169 (1) ◽  
pp. 143-163 ◽  
Author(s):  
DMITRY L. GRODNTTSKY ◽  
PAHVEL P. MOROZOV
Keyword(s):  
Spatial Structure ◽  
Functional Morphology ◽  
Insect Flight ◽  
Separation Bubble ◽  
Leading Edge ◽  
Vortex Wake ◽  
Green Lacewings ◽  
Visualization Experiments ◽  
Edge Separation ◽  
Stroke Cycle

Experiments on dust visualization of the flow around tethered flying green lacewings showed that, contrary to expectations based on the Weis-Fogh clap-andfling mechanism, a leading edge separation bubble does not exist near either fore-or hindwings. At the beginning of the stroke cycle each wing operates as an independent generator of vorticity. The vortex bubbles of all the four wings then unite, producing a single U-shaped bubble. A hypothetical spatial structure for the vortex wake is derived from a series of registrated sections of the wake illuminated with a flat light beam. Some problems of wing functional morphology and insect flight aerodynamics are also discussed.

Sign in / Sign up

Export Citation Format

Share Document