A theoretical investigation of enhanced lift in the presence of thin aerofoil stall

1999 ◽  
Vol 103 (1023) ◽  
pp. 237-244 ◽  
Author(s):  
W. W. H. Yeung ◽  
G. V. Parkinson
Keyword(s):  
Flat Plate ◽  
Flow Model ◽  
Separated Flow ◽  
Leading Edge ◽  
Geometrical Parameters ◽  
Separation Flow ◽  
Attached Flow ◽  
Positive Angle ◽  
Edge Separation ◽  
Potential Flow Model

Abstract A theoretical study is presented for the investigation of a potential-flow model for enhancing lift over a flat-plate aerofoil experiencing thin aerofoil stall. Rather than suppressing the leading-edge separation, flow is assumed to separate tangentially at the leading edge and made to reattach smoothly at the tip of a forward-facing fence joining the plate tangentially on its upper surface to avoid any unnecessary stagnated flow. The length of the fence and its location from the leading edge form two geometrical parameters. At any positive angle of attack, the resulting bounding streamline emanating from the leading edge and terminating at the tip of the fence is simulated by using suitable mathematical singularities subject to boundary conditions such as attaining a finite velocity at each critical point of the conformal mapping involved, and the condition of finite pressure gradient at reattachment, when applicable. Computational results from varying these two geometrical parameters indicate that the lift from each model is enhanced, as compared with the attached flow model around a simple flat plate and the original separated flow model by Kirchhoff.

On the steady separated flow around an inclined flat plate

1997 ◽  
Vol 333 ◽  
pp. 403-413 ◽  
Author(s):  
W. W. H. YEUNG ◽  
G. V. PARKINSON
Keyword(s):  
Flat Plate ◽  
Bluff Body ◽  
Separation Bubble ◽  
Separated Flow ◽  
Leading Edge ◽  
Source Model ◽  
Pressure Distributions ◽  
Wide Range ◽  
Trailing Edges ◽  
Edge Separation

An inviscid analytic model is proposed for the steady separated flow around an inclined flat plate. With the plate normal to the stream, the model reduces to the wake-source model of Parkinson & Jandali originally developed for flow external to a symmetrical two-dimensional bluff body and its wake. At any other inclination, the Kutta condition is satisfied at both leading and trailing edges of the plate, and, in the limit that the angle of attack approaches zero, classical airfoil theory is recovered. A boundary condition is formulated based on some experimental results of Abernathy, but no additional empirical information is required. The predicted pressure distributions on the wetted surface for a wide range of angle attack are found to be in good agreement with experimental data, especially at smaller angles of attack. An extension to include a leading-edge separation bubble is explored and results are satisfactory.

Calculation of Attached or Partially Separated Flow Around Airfoil Sections

1977 ◽  
Vol 21 (02) ◽  
pp. 69-81
Author(s):  
Jerome H. Milgram
Keyword(s):  
Separated Flow ◽  
Leading Edge ◽  
Perturbation Series ◽  
Unified Theory ◽  
Physical Plane ◽  
Trailing Edge ◽  
Separation Flows ◽  
Attached Flow ◽  
Approach Zero ◽  
Edge Separation

Two-dimensional airfoil theory is developed for incompressible flow, for which most aspects of the solution are found in a "mapped plane." Although the airfoil contour has large slopes in the physical plane when the airfoil has a round leading edge, the slopes in the mapped plane are small and uniformly approach zero as the airfoil thickness and camber ratios are made to approach zero by an affine transformation on the airfoil shape. Because of the small slopes in the mapped plane, a perturbation series is appropriate there. A relatively unified theory is given for attached and partially separated (trailing-edge separation) flows. The results of calculations by this theory are compared with the results of other theories and with measurements. The attached-flow theory is shown to be especially appropriate for thin marine propeller sections with blunted leading edges. Some new data on the pressure distribution across the wake at the trailing edge of an airfoil in partially separated flow are presented.

scholarly journals Flow Past a Flat Plate With a Vortex/Sink Combination

1996 ◽  
Vol 63 (2) ◽  
pp. 543-550 ◽  
Author(s):  
N. J. Mourtos ◽  
M. Brooks
Keyword(s):  
Flat Plate ◽  
Current Model ◽  
Angle Of Attack ◽  
Separated Flow ◽  
Leading Edge ◽  
Classical Solutions ◽  
Two Dimensional ◽  
Trailing Edge ◽  
Kutta Condition ◽  
Attached Flow

This paper presents a potential flow model for the leading edge vortex over a two-dimensional flat plate at an angle of attack. The paper is an extension of a model by Saffman and Sheffield (1977). A sink has been added in this model in an effort to satisfy the Kutta condition at both the leading edge and the trailing edge of the plate. The introduction of the sink was inspired by the fact that most steady vortices in nature appear in combination with a flow feature which can be interpreted as a sink at their cores when the flow is analyzed in a two-dimensional observation plane. As in the Saffman and Sheffield model, the presence of a vortex results in increased lift; however, in the current model a unique vortex/sink position is found at each angle of attack. A comparison has also been made between the lift and the drag of this model and the corresponding results for two classical solutions of flow over a flat plate: (a) the fully attached flow with the Kutta condition satisfied at the trailing edge only and (b) the Helmholtz solution of fully separated flow.

Three-Dimensional and Rotational Aerodynamics on the NREL Phase VI Wind Turbine Blade

2008 ◽  
Vol 130 (3) ◽  
Author(s):  
Alvaro Gonzalez ◽  
Xabier Munduate
Keyword(s):  
Wind Turbine ◽  
Turbine Blade ◽  
Three Dimensional ◽  
Separated Flow ◽  
Leading Edge ◽  
Wind Turbine Blade ◽  
Trailing Edge ◽  
Rotating Blade ◽  
Nrel Phase Vi ◽  
Edge Separation

This work undertakes an aerodynamic analysis over the parked and the rotating NREL Phase VI wind turbine blade. The experimental sequences from NASA Ames wind tunnel selected for this study respond to the parked blade and the rotating configuration, both for the upwind, two-bladed wind turbine operating at nonyawed conditions. The objective is to bring some light into the nature of the flow field and especially the type of stall behavior observed when 2D aerofoil steady measurements are compared to the parked blade and the latter to the rotating one. From averaged pressure coefficients together with their standard deviation values, trailing and leading edge separated flow regions have been found, with the limitations of the repeatability of the flow encountered on the blade. Results for the parked blade show the progressive delay from tip to root of the trailing edge separation process, with respect to the 2D profile, and also reveal a local region of leading edge separated flow or bubble at the inner, 30% and 47% of the blade. For the rotating blade, results at inboard 30% and 47% stations show a dramatic suppression of the trailing edge separation, and the development of a leading edge separation structure connected with the extra lift.

Sparse identification of nonlinear unsteady aerodynamics of the oscillating airfoil

2020 ◽  
pp. 095441002095987
Author(s):  
Chong Sun ◽  
Tian Tian ◽  
Xiaocheng Zhu ◽  
Zhaohui Du
Keyword(s):  
Flow Model ◽  
Dynamic Change ◽  
Unsteady Aerodynamics ◽  
Separated Flow ◽  
General System ◽  
Training Data ◽  
Loop Control ◽  
First Order ◽  
Attached Flow ◽  
Unsteady Lift

Reduced-order models are widely used in aerospace engineering. A model for unsteady aerodynamics is desirable for designing the blades of wind turbines. Recently, sparse identification of nonlinear dynamics with control was introduced to identify the parameters of an input-output dynamical system. In this paper, two models for attached flows and one for separated flows are identified through this technique. For the unsteady lift of the attached flow, Model I is a linear model that presents the dynamic change of an unsteady lift to a static lift. Model II was built based on Model I in order to obtain a more general system with closed-loop control. It has a first-order inert element that delays the overall input of the static lift. The Model II results replicate the training data very well and give an accurate prediction of other oscillating cases with different oscillation amplitudes, reduced frequency or mean angle of attack. For the unsteady lift of the separated flow, Model III is identified as a nonlinear model, which also has a first-order inert element. This model captures the nonlinear aerodynamics of the separated flow and replicates the training cases well. In addition, the prediction of Model III has good agreement with the numerical results.

Investigation of aerodynamic coefficients at Mach 6 over conical, hemispherical and flat-face spiked body

2017 ◽  
Vol 121 (1245) ◽  
pp. 1711-1732 ◽  
Author(s):  
R. Kalimuthu ◽  
R. C. Mehta ◽  
E. Rathakrishnan
Keyword(s):  
Flow Field ◽  
Blunt Body ◽  
Angle Of Attack ◽  
Separated Flow ◽  
Leading Edge ◽  
Aerodynamic Characteristics ◽  
Geometrical Parameters ◽  
Aerodynamic Coefficients ◽  
Aerodynamic Forces ◽  
Flow Field Characteristics

ABSTRACTA forward spike attached to a blunt body significantly alters its flow field characteristics and influences aerodynamic characteristics at hypersonic flow due to formation of separated flow and re-circulation region around the spiked body. An experimental investigation was performed to measure aerodynamic forces for spikes blunt bodies with a conical, hemispherical and flat-face spike at Mach 6 and at an angle-of-attack range from 0° to 8° and length-to-diameterL/Dratio of spike varies from 0.5 to 2.0, whereLis the length of the spike andDis diameter of blunt body. The shape of the leading edge of the spiked blunt body reveals different types of flow field features in the formation of a shock wave, shear layer, flow separation, re-circulation region and re-attachment shock. They are analysed with the help of schlieren pictures. The shock distance ahead of the hemisphere and the flat-face spike is compared with the analytical solution and is showing satisfactory agreement with the schlieren pictures. The influence of geometrical parameters of the spike, the shape of the spike tip and angle-of-attack on the aerodynamic coefficients are investigated by measuring aerodynamic forces in a hypersonic wind tunnel. It is found that a maximum reduction of drag of about 77% was found for hemisphere spike ofL/D= 2.0 at zero angle-of-attack. Consideration for compensation of increased pitching moment is required to stabilise the aerodynamic forces.

Predicting Transitional Separation Bubbles

2004 ◽  
Vol 127 (3) ◽  
pp. 497-501
Author(s):  
John A. Redford ◽  
Mark W. Johnson
Keyword(s):  
Boundary Layer ◽  
Separation Bubble ◽  
Separated Flow ◽  
Leading Edge ◽  
Transition Process ◽  
Test Cases ◽  
Transition Model ◽  
Flow Transition ◽  
Free Stream Turbulence ◽  
Attached Flow

This paper describes the modifications made to a successful attached flow transition model to produce a model capable of predicting both attached and separated flow transition. This transition model is used in combination with the Fluent CFD software, which is used to compute the flow around the blade assuming that it remains entirely laminar. The transition model then determines the start of transition location and the development of the intermittency. These intermittency values weight the laminar and turbulent boundary layer profiles to obtain the resulting transitional boundary layer parameters. The ERCOFTAC T3L test cases are used to validate the predictions. The T3L blade is a flat plate with a semi-circular leading edge, which results in the formation of a separation bubble the length of which is strongly dependent on the transition process. Predictions were performed for five T3L test cases for differing free-stream turbulence levels and Reynolds numbers. For the majority of these test cases the measurements were accurately predicted.

Predicting Transitional Separation Bubbles

2004 ◽  
Author(s):  
John A. Redford ◽  
Mark W. Johnson
Keyword(s):  
Boundary Layer ◽  
Separation Bubble ◽  
Separated Flow ◽  
Leading Edge ◽  
Transition Process ◽  
Reynolds Numbers ◽  
Test Cases ◽  
Transition Model ◽  
Flow Transition ◽  
Attached Flow

This paper describes the modifications made to a successful attached flow transition model to produce a model capable of predicting both attached and separated flow transition. This transition model is used in combination with the Fluent CFD software, which is used to compute the flow around the blade assuming that it remains entirely laminar. The transition model then determines the start of transition location and the development of the intermittency. These intermittency values weight the laminar and turbulent boundary layer profiles to obtain the resulting transitional boundary layer parameters. The ERCOFTAC T3L test cases are used to validate the predictions. The T3L blade is a flat plate with a semi-circular leading edge, which results in the formation of a separation bubble the length of which is strongly dependent on the transition process. Predictions were performed for five T3L test cases for differing freestream turbulence levels and Reynolds numbers. For the majority of these test cases the measurements were accurately predicted.

Sign in / Sign up

Export Citation Format

Share Document