scholarly journals Modeling and control of a new robotic deburring system

Robotica ◽  
2005 ◽  
Vol 24 (2) ◽  
pp. 229-237 ◽  
Author(s):  
Jae H. Chung ◽  
Changhoon Kim
Keyword(s):  
Comparative Study ◽  
Decentralized Control ◽  
Control Method ◽  
Robotic Manipulator ◽  
Coordination Control ◽  
Pneumatic Actuators ◽  
Modeling And Control ◽  
Control Approach ◽  
Simulation Results ◽  
And Control

This paper discusses the modeling and control of a robotic manipulator with a new deburring tool, which integrates two pneumatic actuators to take advantage of a double cutting action. A coordination control method is developed by decomposing the robotic deburring system into two subsystems; the arm and the deburring tool. A decentralized control approach is pursued, in which suitable controllers were designed for the two subsystems in the coordination scheme. In simulation, three different tool configurations are considered: rigid, single pneumatic and integrated pneumatic tools. A comparative study is performed to investigate the deburring performance of the deburring arm with the different tools. Simulation results show that the developed robotic deburring system significantly improves the accuracy of the deburring operation.

scholarly journals Modeling and Control of a New Robotic Deburring System

2007 ◽  
Vol 129 (5) ◽  
pp. 965-972 ◽  
Author(s):  
Changhoon Kim ◽  
Jae H. Chung
Keyword(s):  
Feedback Linearization ◽  
Control Method ◽  
Pneumatic Cylinder ◽  
Coordination Control ◽  
External Disturbances ◽  
Pneumatic Actuators ◽  
Modeling And Control ◽  
Control Approach ◽  
And Control ◽  
Speed Simulation

This paper discusses the modeling and control of a robotic manipulator with a new deburring tool, which integrates two pneumatic actuators to take advantage of a double cutting action. A coordination control method was developed by decomposing the robotic deburring system into two subsystems: the arm and the deburring tool. A decentralized control approach was pursued in which suitable controllers were designed for the two subsystems in the coordination scheme. Robust feedback linearization was utilized to minimize the undesirable effect of external disturbances, such as static and Coulomb friction and nonlinear compliance of the pneumatic cylinder stemming from the compressibility of air. The developed coordination control method demonstrated its efficacy in terms of deburring accuracy and speed. Simulation results show that the developed robotic deburring system significantly improves the accuracy of the deburring operation.

Modeling and control of a mobile manipulator

Robotica ◽  
1998 ◽  
Vol 16 (6) ◽  
pp. 607-613 ◽  
Author(s):  
J. H. Chung ◽  
S. A. Velinsky
Keyword(s):  
Dynamic Model ◽  
Control Method ◽  
Harmful Effect ◽  
Euler Method ◽  
Friction Model ◽  
Mobile Manipulator ◽  
Wheel Slip ◽  
Modeling And Control ◽  
Control Approach ◽  
And Control

This paper concerns the modeling and control of a mobile manipulator which consists of a robotic arm mounted upon a mobile platform. The equations of motion are derived using the Lagrange-d'Alembert formulation for the nonholonomic model of the mobile manipulator. The dynamic model which considers slip of the platform's tires is developed using the Newton-Euler method and incorporates Dugoff's tire friction model. Then, the tracking problem is investigated by using a well known nonlinear control method for the nonholonomic model. The adverse effect of the wheel slip on the tracking of commanded motion is discussed in the simulation. For the dynamic model, a variable structure control approach is employed to minimize the harmful effect of the wheel slip on the tracking performance. The simulation results demonstrate the effectiveness of the proposed control algorithm.

Research of Modeling and Control Method for Electromagnetic Levitation System

2014 ◽  
Vol 651-653 ◽  
pp. 812-817 ◽  
Author(s):  
Jian Guo Zheng ◽  
Zhi Gang Zou ◽  
Hui Zeng ◽  
Tian Peng He
Keyword(s):  
Control Method ◽  
State Space Model ◽  
Electromagnetic Levitation ◽  
Open Loop ◽  
Modeling And Control ◽  
Control Approach ◽  
Control Scheme ◽  
Levitation System ◽  
And Control ◽  
Assignment Scheme

There has been wide interest in the control scheme of the electromagnetic levitation system due to its disadvantages of nonlinearity and open-loop uncertainty. A typical coil-ball levitation system is used in research. The forces of the ball are analyzed and a dynamic model of the whole electromagnetic levitation system is established. Based on the nonlinear state-space model, the coil-ball system is linearized and then a LQR control approach is proposed. Simulation results show that, compared with conventional pole assignment scheme, the electromagnetic levitation system under the proposed control approach gets a better performance, including smaller overshot and faster response.

An Efficient Approach for Modeling and Control of a Quadrotor

2016 ◽  
Vol 4 (2) ◽  
pp. 1-16
Author(s):  
Ahmed S. Khusheef
Keyword(s):  
Pid Control ◽  
Control Method ◽  
Mechanical Design ◽  
Loop Control ◽  
Modeling And Control ◽  
Loop Control System ◽  
And Control ◽  
Close Loop Control ◽  
Close Loop Control System ◽  
Made In

 A quadrotor is a four-rotor aircraft capable of vertical take-off and landing, hovering, forward flight, and having great maneuverability. Its platform can be made in a small size make it convenient for indoor applications as well as for outdoor uses. In model there are four input forces that are essentially the thrust provided by each propeller attached to each motor with a fixed angle. The quadrotor is basically considered an unstable system because of the aerodynamic effects; consequently, a close-loop control system is required to achieve stability and autonomy. Such system must enable the quadrotor to reach the desired attitude as fast as possible without any steady state error. In this paper, an optimal controller is designed based on a Proportional Integral Derivative (PID) control method to obtain stability in flying the quadrotor. The dynamic model of this vehicle will be also explained by using Euler-Newton method. The mechanical design was performed along with the design of the controlling algorithm. Matlab Simulink was used to test and analyze the performance of the proposed control strategy. The experimental results on the quadrotor demonstrated the effectiveness of the methodology used.

DUTY-CYCLED SPINNING BASED 3D MOTION CONTROL APPROACH FOR BEVEL-TIPPED FLEXIBLE NEEDLE INSERTION

2018 ◽  
Vol 18 (07) ◽  
pp. 1840017 ◽  
Author(s):  
QIN YAO ◽  
XUMING ZHANG
Keyword(s):  
Motion Control ◽  
Control Method ◽  
Tracking Error ◽  
Open Loop ◽  
Loop Control ◽  
3D Motion ◽  
Control Approach ◽  
Target Error ◽  
The Mean ◽  
Simulation Results

Flexible needle has been widely used in the therapy delivery because it can advance along the curved lines to avoid the obstacles like important organs and bones. However, most control algorithms for the flexible needle are still limited to address its motion along a set of arcs in the two-dimensional (2D) plane. To resolve this problem, this paper has proposed an improved duty-cycled spinning based three-dimensional (3D) motion control approach to ensure that the beveled-tip flexible needle can track a desired trajectory to reach the target within the tissue. Compared with the existing open-loop duty-cycled spinning method which is limited to tracking 2D trajectory comprised of few arcs, the proposed closed-loop control method can be used for tracking any 3D trajectory comprised of numerous arcs. Distinctively, the proposed method is independent of the tissue parameters and robust to such disturbances as tissue deformation. In the trajectory tracking simulation, the designed controller is tested on the helical trajectory, the trajectory generated by rapidly-exploring random tree (RRT) algorithm and the helical trajectory. The simulation results show that the mean tracking error and the target error are less than 0.02[Formula: see text]mm for the former two kinds of trajectories. In the case of tracking the helical trajectory, the mean tracking error target error is less than 0.5[Formula: see text]mm and 1.5[Formula: see text]mm, respectively. The simulation results prove the effectiveness of the proposed method.

scholarly journals Modeling and Simulation of Energy Management Hybrid Sources System composed of Solar-PV and Battery

2016 ◽  
Vol 1 (1) ◽  
pp. 12
Author(s):  
Madiha Maamir ◽  
Achour Betka ◽  
Hania Aboub
Keyword(s):  
Energy Management ◽  
Solar Pv ◽  
Modeling And Control ◽  
Control Techniques ◽  
Simulation Results ◽  
Power Manager ◽  
And Control ◽  
Different Sources ◽  
Pv Generator ◽  
Auxiliary Source

This paper describes the  modeling and control of a hybrid source consisting of PV generator (as  main  source)  along  with  a  battery (as  an  auxiliary source)  and a dc-load are connected through power converters and a dc-link. The main objective of this paper is to design a power manager to control effectively the power of the different sources. To test the effectiveness of the different control techniques involved, simulation results are plotted and commented.

Decentralized Control of a Tower Crane

1999 ◽  
Author(s):  
Kiyoshi Takagi ◽  
Hidekazu Nishimura
Keyword(s):  
Decentralized Control ◽  
Three Dimensional ◽  
Reduced Order Model ◽  
Flexible Structure ◽  
Order Model ◽  
Modeling And Control ◽  
Reduced Order ◽  
Tower Crane ◽  
Three Dimensional Models ◽  
And Control

Abstract This paper deals with modeling and control of a crane mounted on a tower-like flexible structure. A fast transfer of the load causes the sway of the load rope and the vibration of the flexible structure. Our object is to control both the sway and the vibration by the inherent capability of the tower crane. This paper makes its three-dimensional models for simulation and reduced-order-model in order to design the decentralized control system. Then, we design the decentralized H∞ compensator and verify the efficiency by simulations and experiments.

Intelligent Motion Planning and Control for Robotic Joints Using Bio-Inspired Spiking Neural Networks

2019 ◽  
Vol 16 (04) ◽  
pp. 1950012 ◽  
Author(s):  
Mircea Hulea ◽  
Adrian Burlacu ◽  
Constantin-Florin Caruntu
Keyword(s):  
Neural Network ◽  
Neural Networks ◽  
Motion Planning ◽  
Control Method ◽  
Inhibitory Neurons ◽  
Robotic Arm ◽  
Control Approach ◽  
Planning And Control ◽  
Robotic Joints ◽  
And Control

This paper details an intelligent motion planning and control approach for a one-degree of freedom joint of a robotic arm that can be used to implement anthropomorphic robotic hands. This intelligent control method is based on bio-inspired electronic neural networks and contractile artificial muscles implemented with shape memory alloy (SMA) actuators. The spiking neural network (SNN) includes several excitatory neurons that naturally determine the contraction force of the actuators, and unevenly distributed inhibitory neurons that regulate the excitatory activity. To validate the proposed concept, the experiments highlight the motion planning and control of a single-joint robotic arm. The results show that the electronic neural network is able to intelligently activate motion and hold with high precision the mobile link to the target positions even if the arm is slightly loaded. These results are encouraging for the development of improved biologically plausible neural structures that are able to control simultaneously multiple muscles.

scholarly journals Hybrid modeling and control of ICPT system with synchronous three-phase triple-parallel Buck converter

2020 ◽  
Vol 7 (1) ◽  
pp. 10-18
Author(s):  
Songcen Wang ◽  
Xiaokang Wu ◽  
Ying Yang ◽  
Cong Zhu ◽  
Zhen Wu ◽  
...  
Keyword(s):  
Coupling Coefficient ◽  
Control Method ◽  
Buck Converter ◽  
Constant Voltage ◽  
Modeling And Control ◽  
Coefficient Variation ◽  
Current Sharing ◽  
Voltage Output ◽  
Three Phase ◽  
And Control

AbstractAiming at the influence of coupling coefficient variation on the output voltage of a high-power LCC-S topology inductively coupled power transfer (ICPT) system, a synchronous three-phase triple-parallel Buck converter is used as the voltage adjustment unit. The control method for the three-phase current sharing of synchronous three-phase triple-parallel Buck converter and the constant voltage output ICPT system under the coupling coefficient variation is studied. Firstly, the hybrid model consisting of the circuit averaging model of the three-phase triple-parallel Buck converter and the generalized state-space average model for the LCC-S type ICPT system is established. Then, the control methods for three-phase current sharing of the synchronous three-phase triple-parallel Buck converter and constant voltage output of ICPT system are studied to achieve the multi-objective integrated control of the system. Finally, a 3.3 kW wireless charging system platform is built, the experimental results have verified the effectiveness of the proposed modeling and control method, and demonstrated the stability of the ICPT system.

Sign in / Sign up

Export Citation Format

Share Document