IMU-Based Gait Phase Recognition for Stroke Survivors

Robotica ◽  
2019 ◽  
Vol 37 (12) ◽  
pp. 2195-2208 ◽  
Author(s):  
Yu Lou ◽  
Rongli Wang ◽  
Jingeng Mai ◽  
Ninghua Wang ◽  
Qining Wang
Keyword(s):  
Inertial Measurement Unit ◽  
Detection System ◽  
Effective Means ◽  
Human Motion ◽  
Measurement Unit ◽  
Stroke Survivors ◽  
Phase Detection ◽  
Wearable Robots ◽  
Gait Phase ◽  
Phase Recognition

SummaryUsing wearable robots is an effective means of rehabilitation for stroke survivors, and effective recognition of human motion intentions is a key premise in controlling wearable robots. In this paper, we propose an inertial measurement unit (IMU)-based gait phase detection system. The system consists of two IMUs that are tied on the thigh and on the shank, respectively, for collecting acceleration and angular velocity. Features were extracted using a sliding window of 150 ms in length, which was then fed into a quadratic discriminant analysis (QDA) classifier for classification. We recruited five stroke survivors to test our system. They walked at their own preferred speed on the level ground. Experimental results show that our proposed system has the ability of recognizing the gait phase of stroke survivors. All recognition accuracy results are above 96.5%, and detections are about 5–15 ms in advance of time. In addition, using only one IMU can also give reliable recognition results. This paper proposes an idea about the further research on human–computer interaction for the control of wearable robots.

Gait phase detection based on inertial measurement unit and force-sensitive resistors embedded in a shoe

2021 ◽  
Vol 92 (8) ◽  
pp. 084708
Author(s):  
Xianwen Liu ◽  
Shimin Zhang ◽  
Benchun Yao ◽  
Yang Yu ◽  
Yusong Wang ◽  
...  
Keyword(s):  
Inertial Measurement Unit ◽  
Measurement Unit ◽  
Phase Detection ◽  
Inertial Measurement ◽  
Gait Phase

scholarly journals Gait Phase Detection for Lower-Limb Exoskeletons using Foot Motion Data from a Single Inertial Measurement Unit in Hemiparetic Individuals

Sensors ◽  
2019 ◽  
Vol 19 (13) ◽  
pp. 2988 ◽  
Author(s):  
Miguel D. Sánchez Sánchez Manchola ◽  
María J. Pinto Pinto Bernal ◽  
Marcela Munera ◽  
Carlos A. Cifuentes
Keyword(s):  
Lower Limb ◽  
Inertial Measurement Unit ◽  
Low Cost ◽  
Linear Acceleration ◽  
Measurement Unit ◽  
Phase Detection ◽  
Inertial Measurement ◽  
Phase Partitioning ◽  
Motion Data ◽  
Gait Phase

Due to the recent rise in the use of lower-limb exoskeletons as an alternative for gait rehabilitation, gait phase detection has become an increasingly important feature in the control of these devices. In addition, highly functional, low-cost recovery devices are needed in developing countries, since limited budgets are allocated specifically for biomedical advances. To achieve this goal, this paper presents two gait phase partitioning algorithms that use motion data from a single inertial measurement unit (IMU) placed on the foot instep. For these data, sagittal angular velocity and linear acceleration signals were extracted from nine healthy subjects and nine pathological subjects. Pressure patterns from force sensitive resistors (FSR) instrumented on a custom insole were used as reference values. The performance of a threshold-based (TB) algorithm and a hidden Markov model (HMM) based algorithm, trained by means of subject-specific and standardized parameters approaches, were compared during treadmill walking tasks in terms of timing errors and the goodness index. The findings indicate that HMM outperforms TB for this hardware configuration. In addition, the HMM-based classifier trained by an intra-subject approach showed excellent reliability for the evaluation of mean time, i.e., its intra-class correlation coefficient (ICC) was greater than 0 . 75 . In conclusion, the HMM-based method proposed here can be implemented for gait phase recognition, such as to evaluate gait variability in patients and to control robotic orthoses for lower-limb rehabilitation.

scholarly journals Gait Phase Detection Based on Muscle Deformation with Static Standing-Based Calibration

Sensors ◽  
2021 ◽  
Vol 21 (4) ◽  
pp. 1081
Author(s):  
Tamon Miyake ◽  
Shintaro Yamamoto ◽  
Satoshi Hosono ◽  
Satoshi Funabashi ◽  
Zhengxue Cheng ◽  
...  
Keyword(s):  
Learning Algorithm ◽  
Detection System ◽  
Calibration Method ◽  
Detection Algorithm ◽  
Video Data ◽  
Detection Accuracy ◽  
Phase Detection ◽  
Gait Phase ◽  
Logistic Regression Algorithm ◽  
Short Time

Gait phase detection, which detects foot-contact and foot-off states during walking, is important for various applications, such as synchronous robotic assistance and health monitoring. Gait phase detection systems have been proposed with various wearable devices, sensing inertial, electromyography, or force myography information. In this paper, we present a novel gait phase detection system with static standing-based calibration using muscle deformation information. The gait phase detection algorithm can be calibrated within a short time using muscle deformation data by standing in several postures; it is not necessary to collect data while walking for calibration. A logistic regression algorithm is used as the machine learning algorithm, and the probability output is adjusted based on the angular velocity of the sensor. An experiment is performed with 10 subjects, and the detection accuracy of foot-contact and foot-off states is evaluated using video data for each subject. The median accuracy is approximately 90% during walking based on calibration for 60 s, which shows the feasibility of the static standing-based calibration method using muscle deformation information for foot-contact and foot-off state detection.

scholarly journals Analysis of the Accuracy of Ten Algorithms for Orientation Estimation Using Inertial and Magnetic Sensing Under Optimal Conditions: One Size Does Not Fit All

Sensors ◽  
2021 ◽  
Vol 21 (7) ◽  
pp. 2543
Author(s):  
Marco Caruso ◽  
Angelo Maria Sabatini ◽  
Daniel Laidig ◽  
Thomas Seel ◽  
Marco Knaflitz ◽  
...  
Keyword(s):  
Inertial Measurement Unit ◽  
Motion Tracking ◽  
Recent Literature ◽  
Human Motion ◽  
Measurement Unit ◽  
Optimal Conditions ◽  
Inertial Measurement ◽  
Rotation Rates ◽  
Significant Performance ◽  
Parameter Values

The orientation of a magneto and inertial measurement unit (MIMU) is estimated by means of sensor fusion algorithms (SFAs) thus enabling human motion tracking. However, despite several SFAs implementations proposed over the last decades, there is still a lack of consensus about the best performing SFAs and their accuracy. As suggested by recent literature, the filter parameters play a central role in determining the orientation errors. The aim of this work is to analyze the accuracy of ten SFAs while running under the best possible conditions (i.e., their parameter values are set using the orientation reference) in nine experimental scenarios including three rotation rates and three commercial products. The main finding is that parameter values must be specific for each SFA according to the experimental scenario to avoid errors comparable to those obtained when the default parameter values are used. Overall, when optimally tuned, no statistically significant differences are observed among the different SFAs in all tested experimental scenarios and the absolute errors are included between 3.8 deg and 7.1 deg. Increasing the rotation rate generally leads to a significant performance worsening. Errors are also influenced by the MIMU commercial model. SFA MATLAB implementations have been made available online.

scholarly journals Design and Voluntary Motion Intention Estimation of a Novel Wearable Full-Body Flexible Exoskeleton Robot

2017 ◽  
Vol 2017 ◽  
pp. 1-11 ◽  
Author(s):  
Chunjie Chen ◽  
Xinyu Wu ◽  
Du-xin Liu ◽  
Wei Feng ◽  
Can Wang
Keyword(s):  
Gait Cycle ◽  
Human Motion ◽  
Experimental Result ◽  
Motion Patterns ◽  
Exoskeleton Robot ◽  
Gait Phase ◽  
Phase Recognition ◽  
Motion Intention ◽  
Full Body ◽  
Testing Set

The wearable full-body exoskeleton robot developed in this study is one application of mobile cyberphysical system (CPS), which is a complex mobile system integrating mechanics, electronics, computer science, and artificial intelligence. Steel wire was used as the flexible transmission medium and a group of special wire-locking structures was designed. Additionally, we designed passive joints for partial joints of the exoskeleton. Finally, we proposed a novel gait phase recognition method for full-body exoskeletons using only joint angular sensors, plantar pressure sensors, and inclination sensors. The method consists of four procedures. Firstly, we classified the three types of main motion patterns: normal walking on the ground, stair-climbing and stair-descending, and sit-to-stand movement. Secondly, we segregated the experimental data into one gait cycle. Thirdly, we divided one gait cycle into eight gait phases. Finally, we built a gait phase recognition model based on k-Nearest Neighbor perception and trained it with the phase-labeled gait data. The experimental result shows that the model has a 98.52% average correct rate of classification of the main motion patterns on the testing set and a 95.32% average correct rate of phase recognition on the testing set. So the exoskeleton robot can achieve human motion intention in real time and coordinate its movement with the wearer.

scholarly journals Gait Phase Recognition Using Deep Convolutional Neural Network with Inertial Measurement Units

Biosensors ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 109
Author(s):  
Binbin Su ◽  
Christian Smith ◽  
Elena Gutierrez Farewik
Keyword(s):  
Wearable Sensors ◽  
Sensor Data ◽  
Measurement Unit ◽  
Deep Convolutional Neural Networks ◽  
Inertial Measurement ◽  
Measurement Units ◽  
Gait Phase ◽  
Robotic Devices ◽  
Phase Recognition ◽  
Five Phases

Gait phase recognition is of great importance in the development of assistance-as-needed robotic devices, such as exoskeletons. In order for a powered exoskeleton with phase-based control to determine and provide proper assistance to the wearer during gait, the user’s current gait phase must first be identified accurately. Gait phase recognition can potentially be achieved through input from wearable sensors. Deep convolutional neural networks (DCNN) is a machine learning approach that is widely used in image recognition. User kinematics, measured from inertial measurement unit (IMU) output, can be considered as an ‘image’ since it exhibits some local ‘spatial’ pattern when the sensor data is arranged in sequence. We propose a specialized DCNN to distinguish five phases in a gait cycle, based on IMU data and classified with foot switch information. The DCNN showed approximately 97% accuracy during an offline evaluation of gait phase recognition. Accuracy was highest in the swing phase and lowest in terminal stance.

scholarly journals Walking Gait Phase Detection Based on Acceleration Signals Using LSTM-DNN Algorithm

Algorithms ◽  
2019 ◽  
Vol 12 (12) ◽  
pp. 253 ◽  
Author(s):  
Tao Zhen ◽  
Lei Yan ◽  
Peng Yuan
Keyword(s):  
Short Term Memory ◽  
Disease Diagnosis ◽  
Detection Accuracy ◽  
Phase Detection ◽  
Data Set ◽  
Softmax Classifier ◽  
Acceleration Sensors ◽  
Gait Phase ◽  
Phase Recognition ◽  
Acceleration Signals

Gait phase detection is a new biometric method which is of great significance in gait correction, disease diagnosis, and exoskeleton assisted robots. Especially for the development of bone assisted robots, gait phase recognition is an indispensable key technology. In this study, the main characteristics of the gait phases were determined to identify each gait phase. A long short-term memory-deep neural network (LSTM-DNN) algorithm is proposed for gate detection. Compared with the traditional threshold algorithm and the LSTM, the proposed algorithm has higher detection accuracy for different walking speeds and different test subjects. During the identification process, the acceleration signals obtained from the acceleration sensors were normalized to ensure that the different features had the same scale. Principal components analysis (PCA) was used to reduce the data dimensionality and the processed data were used to create the input feature vector of the LSTM-DNN algorithm. Finally, the data set was classified using the Softmax classifier in the full connection layer. Different algorithms were applied to the gait phase detection of multiple male and female subjects. The experimental results showed that the gait-phase recognition accuracy and F-score of the LSTM-DNN algorithm are over 91.8% and 92%, respectively, which is better than the other three algorithms and also verifies the effectiveness of the LSTM-DNN algorithm in practice.

scholarly journals Towards Human Motion Tracking: Multi-Sensory IMU/TOA Fusion Method and Fundamental Limits

Electronics ◽  
2019 ◽  
Vol 8 (2) ◽  
pp. 142 ◽  
Author(s):  
Cheng Xu ◽  
Jie He ◽  
Xiaotong Zhang ◽  
Xinghang Zhou ◽  
Shihong Duan
Keyword(s):  
Inertial Measurement Unit ◽  
Motion Tracking ◽  
Human Motion ◽  
Measurement Unit ◽  
Time Of Arrival ◽  
Fusion Method ◽  
Tracking Accuracy ◽  
Fundamental Limits ◽  
Inertial Measurement ◽  
Human Motion Tracking

Human motion tracking could be viewed as a multi-target tracking problem towards numerous body joints. Inertial-measurement-unit-based human motion tracking technique stands out and has been widely used in body are network applications. However, it has been facing the tough problem of accumulative errors and drift. In this paper, we propose a multi-sensor hybrid method to solve this problem. Firstly, an inertial-measurement-unit and time-of-arrival fusion-based method is proposed to compensate the drift and accumulative errors caused by inertial sensors. Secondly, Cramér–Rao lower bound is derived in detail with consideration of both spatial and temporal related factors. Simulation results show that the proposed method in this paper has both spatial and temporal advantages, compared with traditional sole inertial or time-of-arrival-based tracking methods. Furthermore, proposed method is verified in 3D practical application scenarios. Compared with state-of-the-art algorithms, proposed fusion method shows better consistency and higher tracking accuracy, especially when moving direction changes. The proposed fusion method and comprehensive fundamental limits analysis conducted in this paper can provide a theoretical basis for further system design and algorithm analysis. Without the requirements of external anchors, the proposed method has good stability and high tracking accuracy, thus it is more suitable for wearable motion tracking applications.

Sign in / Sign up

Export Citation Format

Share Document