The jet from a horizontal slot at large Froude number

1973 ◽  
Vol 73 (3) ◽  
pp. 515-529 ◽  
Author(s):  
G. Keady
Keyword(s):  
Asymptotic Expansion ◽  
Flow Field ◽  
Froude Number ◽  
Asymptotic Expansions ◽  
Complex Potential ◽  
Horizontal Plane ◽  
Two Dimensional ◽  
Outer Expansion ◽  
Two Dimensional Flow ◽  
Independent Variable

The two-dimensional flow in a jet, falling under gravity from a slot in a horizontal plane, is studied. The fluid is considered to be incompressible and inviscid; the flow is taken to be irrotational; and the reciprocal ε of the Froude number is considered to be small. By taking the complex potential as the independent variable we overcome the difficulty that the boundary geometry is not known in advance. The method of matched asymptotic expansions is applied. The first two terms of an inner asymptotic expansion and the first three of an outer one are found: the inner expansion is valid above and near the slot, but is inappropriate far downstream, while the outer expansion is valid far downstream, but fails to satisfy the conditions upstream. The two expansions are matched and ‘composite’ approximations, covering the whole flow field, are derived.

On two-dimensional inviscid flow in a waterfall

1965 ◽  
Vol 22 (2) ◽  
pp. 359-369 ◽  
Author(s):  
N. S. Clarke
Keyword(s):  
Asymptotic Expansion ◽  
Flow Field ◽  
Froude Number ◽  
Inviscid Flow ◽  
Two Dimensional ◽  
Dimensional Flow ◽  
Free Streamlines ◽  
Two Dimensional Flow ◽  
Boundary Geometry

This paper is concerned with the two-dimensional flow in a free waterfall, falling under the influence of gravity, the fluid being considered to be incompressible and inviscid. A parameter ε, such that 2/ε is the Froude number based on conditions far upstream, is defined and considered to be small. A flowline co-ordinate system is used to overcome the difficulty that the boundary geometry is not known in advance. An asymptotic expansion based on ε is constructed as an approximation valid upstream and near the edge, but singular far downstream. Another asymptotic expansion, based upon the thinness of the fall, is constructed as an approximation valid far downstream, but failing to satisfy the conditions upstream. The two expansions are then matched to give a solution covering the whole flow field. The shapes of the free streamlines are shown for a number of values of ε for which the solutions are seemingly valid.

scholarly journals Two-dimensional flow field distribution characteristics of flocking drainage pipes in tunnel

Open Physics ◽  
2020 ◽  
Vol 18 (1) ◽  
pp. 139-148
Author(s):  
Shiyang Liu ◽  
Xuefu Zhang ◽  
Feng Gao ◽  
Liangwen Wei ◽  
Qiang Liu ◽  
...  
Keyword(s):  
Flow Field ◽  
Field Distribution ◽  
Rapid Development ◽  
Maximum Velocity ◽  
Distribution Characteristics ◽  
Two Dimensional ◽  
Dimensional Flow ◽  
Laboratory Test Results ◽  
Transverse Distance ◽  
Two Dimensional Flow

AbstractWith the rapid development of traffic infrastructure in China, the problem of crystal plugging of tunnel drainage pipes becomes increasingly salient. In order to build a mechanism that is resilient to the crystal plugging of flocking drainage pipes, the present study used the numerical simulation to analyze the two-dimensional flow field distribution characteristics of flocking drainage pipes under different flocking spacings. Then, the results were compared with the laboratory test results. According to the results, the maximum velocity distribution in the flow field of flocking drainage pipes is closely related to the transverse distance h of the fluff, while the longitudinal distance h of the fluff causes little effect; when the transverse distance h of the fluff is less than 6.25D (D refers to the diameter of the fluff), the velocity between the adjacent transverse fluffs will be increased by more than 10%. Moreover, the velocity of the upstream and downstream fluffs will be decreased by 90% compared with that of the inlet; the crystal distribution can be more obvious in the place with larger velocity while it is less at the lower flow rate. The results can provide theoretical support for building a mechanism to deal with and remove the crystallization of flocking drainage pipes.

Flow Visualization by Means of Contactless Inductive Flow Tomography in the Presence of a Magnetic Brake

2015 ◽  
Vol 15 (1) ◽  
pp. 41-48 ◽  
Author(s):  
Matthias Ratajczak ◽  
Thomas Wondrak ◽  
Klaus Timmel ◽  
Frank Stefani ◽  
Sven Eckert
Keyword(s):  
Magnetic Field ◽  
External Magnetic Field ◽  
Magnetic Fields ◽  
Flow Field ◽  
Continuous Casting ◽  
Flow Structure ◽  
Cross Section ◽  
Two Dimensional ◽  
Slab Casting ◽  
Two Dimensional Flow

AbstractIn continuous casting DC magnetic fields perpendicular to the wide faces of the mold are used to control the flow in the mold. Especially in this case, even a rough knowledge of the flow structure in the mold would be highly desirable. The contactless inductive flow tomography (CIFT) allows to reconstruct the dominating two-dimensional flow structure in a slab casting mold by applying one external magnetic field and by measuring the flow-induced magnetic fields outside the mold. For a physical model of a mold with a cross section of 140 mm×35 mm we present preliminary measurements of the flow field in the mold in the presence of a magnetic brake. In addition, we show first reconstructions of the flow field in a mold with the cross section of 400 mm×100 mm demonstrating the upward scalability of CIFT.

A free-streamline solution for stratified flow into a line sink

1965 ◽  
Vol 21 (3) ◽  
pp. 535-543 ◽  
Author(s):  
Timothy W. Kao
Keyword(s):  
Froude Number ◽  
Inverse Method ◽  
Separated Flows ◽  
Two Dimensional ◽  
Mathematical Solution ◽  
Velocity Discontinuity ◽  
Natural Processes ◽  
A Value ◽  
Line Sink ◽  
Two Dimensional Flow

An analysis is made of the two-dimensional flow under gravity of an inviscid non-diffusive stratified fluid into a line sink, involving a velocity discontinuity in the flow field. The fluid above the discontinuity is stagnant and hence is not drawn into the sink. At sufficiently low values of the modified Froude number, this is the only physically possible mode of flow, and is the cause of flow separation in many industrial and natural processes. A proper mathematical solution for flows with a stagnant zone has so far been lacking. This paper presents such a solution, after posing the problem as one involving a free-streamline, which is the line of velocity discontinuity. The solution to be given here is obtained by an inverse method. It is also found herein that the modified Froude number has a value of 0·345 for all separated flows of the kind in question.

Towed Underwater SPIV Measurement of Flow Fields Around a Surface-Piercing Cylinder With Free Surface Effects

2015 ◽  
Author(s):  
Jeonghwa Seo ◽  
Bumwoo Han ◽  
Shin Hyung Rhee
Keyword(s):  
Boundary Layer ◽  
Free Surface ◽  
Surface Wave ◽  
Flow Field ◽  
Cross Section ◽  
Surface Effects ◽  
Flow Fields ◽  
Two Dimensional ◽  
Two Dimensional Flow ◽  
Wave Induced

Effects of free surface on development of turbulent boundary layer and wake fields were investigated. By measuring flow field around a surface piercing cylinder in various advance speed conditions in a towing tank, free surface effects were identified. A towed underwater Stereoscopic Particle Image Velocimetry (SPIV) system was used to measure the flow field under free surface. The cross section of the test model was water plane shape of the Wigley hull, of which longitudinal length and width were 1.0 m and 100 mm, respectively. With sharp bow shape and slender cross section, flow separation was not expected in two-dimensional flow. Flow fields near the free-surface and in deep location that two-dimensional flow field was expected were measured and compared to identify free-surface effects. Some planes perpendicular to longitudinal direction near the model surface and behind the model were selected to track development of turbulent boundary layer. Froude numbers of the test conditions were from 0.126 to 0.40 and corresponding Reynolds numbers were from 395,000 to 1,250,000. In the lowest Froude number condition, free-surface wave was hardly observed and only free surface effects without surface wave could be identified while violent free-surface behavior due to wave-induced separation dominated the flow fields in the highest Froude number condition. From the instantaneous velocity fields, Time-mean velocity, turbulence kinetic energy, and flow structure derived by proper orthogonal decomposition (POD) were analyzed. As the free-surface effect, development of retarded wake, free-surface waves, and wave-induced separation were mainly observed.

Extension of the Prandtl–Batchelor theorem to three-dimensional flows slowly varying in one direction

2010 ◽  
Vol 654 ◽  
pp. 351-361 ◽  
Author(s):  
M. SANDOVAL ◽  
S. CHERNYSHENKO
Keyword(s):  
Flow Field ◽  
Small Parameter ◽  
Order Approximation ◽  
Three Dimensional ◽  
Inviscid Limit ◽  
Two Dimensional ◽  
Leading Order ◽  
Dimensional Flow ◽  
Two Dimensional Flow

According to the Prandtl–Batchelor theorem for a steady two-dimensional flow with closed streamlines in the inviscid limit the vorticity becomes constant in the region of closed streamlines. This is not true for three-dimensional flows. However, if the variation of the flow field along one direction is slow then it is possible to expand the solution in terms of a small parameter characterizing the rate of variation of the flow field in that direction. Then in the leading-order approximation the projections of the streamlines onto planes perpendicular to that direction can be closed. Under these circumstances the extension of the Prandtl–Batchelor theorem is obtained. The resulting equations turned out to be a three-dimensional analogue of the equations of the quasi-cylindrical approximation.

Boundary conditions at a liquid/air interface in lubrication flows

1982 ◽  
Vol 119 ◽  
pp. 107-120 ◽  
Author(s):  
K. J. Ruschak
Keyword(s):  
Finite Element Method ◽  
Boundary Conditions ◽  
Problem Solution ◽  
Lubrication Approximation ◽  
Two Dimensional ◽  
The Finite Element Method ◽  
Air Interface ◽  
Outer Expansion ◽  
Two Dimensional Flow ◽  
Representative Problem

A difficulty in applying the lubrication approximation to flows where a liquid/air interface forms lies in supplying boundary conditions at the point of formation of the interface that are consistent with the lubrication approximation. The method of matched asymptotic expansions is applied to the flow between partially submerged, counter-rotating rollers, a representative problem from this class, and the lubrication approximation is found to generate the first term of an outer expansion of the problem solution. The first term of an inner expansion describes the two-dimensional flow in the vicinity of the interface, and approximate results are found by the finite-element method. Matching between the inner and outer solutions determines boundary conditions on the pressure and the pressure gradient at the point of formation of the interface which allow the solution to the outer, lubrication flow to be completed.

The radial spread of a liquid jet over a horizontal plane

1964 ◽  
Vol 20 (3) ◽  
pp. 481-499 ◽  
Author(s):  
E. J. Watson
Keyword(s):  
Boundary Layer ◽  
Turbulent Flow ◽  
Thin Layer ◽  
Hydraulic Jump ◽  
Horizontal Plane ◽  
Boundary Layer Theory ◽  
Liquid Jet ◽  
Two Dimensional ◽  
Two Dimensional Flow ◽  
Radial Spread

When a smooth jet of water falls vertically on to a horizontal plane, it spreads out radially in a thin layer bounded by a circular hydraulic jump, outside which the depth is much greater. The motion in the layer is studied here by means of boundary-layer theory, both for laminar and for turbulent flow, and relations are obtained for the radius of the hydraulic jump. These relations are compared with experimental results. The analogous problems of two-dimensional flow are also treated.

Sign in / Sign up

Export Citation Format

Share Document