Simulation Study of the Effects of Nanoporous Structures on Mechanical Properties at Polymer–Metal Interfaces

2019 ◽  
Vol 123 (5) ◽  
pp. 1161-1170
Author(s):  
Toshiaki Miura ◽  
Maki Funada ◽  
Yukihiro Shimoi ◽  
Hiroshi Morita
Keyword(s):  
Mechanical Properties ◽  
Simulation Study ◽  
Polymer Metal ◽  
Metal Interfaces ◽  
Nanoporous Structures

Model Compound Approach for Polymer-Metal InterFaces: ESCA Studies

1984 ◽  
Vol 40 ◽  
Author(s):  
P. N. Sanda ◽  
J. W. Bartha ◽  
B. D. Silverman ◽  
P. S. Ho ◽  
A. R. Rossi
Keyword(s):  
Model Compound ◽  
Amino Groups ◽  
Ether Linkage ◽  
Cu Films ◽  
Polymer Metal ◽  
Terminal Amino ◽  
Metal Interfaces ◽  
Imide Group

AbstractESCA studies of two molecules which are similar in structure to the PMDA and ODA constituents of the PMDA-ODA polyimide monomer are discussed. Their interaction with in-situ evaporated Cr and Cu films are compared. The PMDA model compound interacts with Cr through the imide group, while very little interaction is observed with Cu. The ODA model compound (oxydianiline) interacts with Cr via the ether linkage and the terminal amino groups, whereas very little interaction is observed with Cu.

Charactervation of Adhesion in Thin-Film Materials by the Blister Test

1992 ◽  
Vol 276 ◽  
Author(s):  
Y Z. Chu ◽  
H. S. Jeong ◽  
R. C. White ◽  
C. J. Durning
Keyword(s):  
Fluid Pressure ◽  
Structural Features ◽  
Adhesion Energy ◽  
Pressure Data ◽  
Blister Test ◽  
Constant Rate ◽  
Polymer Metal ◽  
Metal Interfaces ◽  
Peel Tests ◽  
Microscopic Dynamic

ABSTRACTIn this work a blister test is applied to study the adhesion of thin films to substrates. In the blister test one injects a fluid at constant rate at the interface between the substrate and an overlayer to create a “blister”. The fluid pressure is measured as function of time. An analysis gives a reliable way of calculating the adhesion energy Ga. from the time-dependent pressure data. The method was applied to a variety of systems including polymer/polymer, polymer/silicon and polymer/metal interfaces. The results show that the test is very sensitive and is able to determine small adhesion energies inaccessible in conventional peel tests. This work demonstrates that the blister test provides a means of relating the mechanical strength of an interface to its microscopic dynamic and structural features.

Studies on polymer-metal interfaces

Polymer ◽  
1999 ◽  
Vol 40 (14) ◽  
pp. 3989-3994 ◽  
Author(s):  
Dong Ha Kim ◽  
Won Ho Jo
Keyword(s):  
Polymer Metal ◽  
Metal Interfaces

Interfacial Versus Cohesive Failure on Polymer-Metal Interfaces in Electronic Packaging—Effects of Interface Roughness

2002 ◽  
Vol 124 (2) ◽  
pp. 127-134 ◽  
Author(s):  
Qizhou Yao ◽  
Jianmin Qu
Keyword(s):  
Surface Roughness ◽  
Fracture Mechanics ◽  
Electronic Packaging ◽  
Interfacial Adhesion ◽  
Interfacial Strength ◽  
Interface Roughness ◽  
Cohesive Failure ◽  
Mechanics Model ◽  
Polymer Metal ◽  
Metal Interfaces

Debonding of polymer-metal interfaces often involves both interfacial and cohesive failure. Since the cohesive strength of polymers is usually much greater than the polymer-metal interfacial strength, cohesive failure near the interface is usually desired for enhancing the interfacial adhesion. Roughened surfaces generally produce more cohesive failure; therefore, they are used commonly in practice to obtain better adhesion. This paper develops a fracture mechanics model that can be used to quantitatively predict the amount of cohesive failure once the surface roughness data are given. An epoxy/Al interface was investigated using this fracture mechanics model. The predicted amount of cohesive failure as a function of surface roughness compares very well with the experimentally measured values. It is believed that this model can be extended to other polymer–metal interfaces. Contributed by the Electronic and Photonic Packaging Division for publication in the JOURNAL OF ELECTRONIC PACKAGING. Manuscript received by the EPPD.

Positron Beam Analysis of Polymer/Metal Interfaces under Stress

2001 ◽  
Vol 363-365 ◽  
pp. 499-501 ◽  
Author(s):  
R. Escobar Galindo ◽  
A. van Veen ◽  
A. Alba García ◽  
H. Schut ◽  
Jeff T.M. de Hosson
Keyword(s):  
Positron Beam ◽  
Beam Analysis ◽  
Polymer Metal ◽  
Metal Interfaces

The Competition between Adhesive and Cohesive Fracture at Amicro-Patterned Polymer-Metal Interface

2013 ◽  
Vol 577-578 ◽  
pp. 225-228 ◽  
Author(s):  
Olaf van der Sluis ◽  
Joris J.C. Remmers ◽  
M.A.C. Thurlings ◽  
B.J. Welling ◽  
Sander P.M. Noijen
Keyword(s):  
Crack Deflection ◽  
Surface Roughening ◽  
Adhesive Failure ◽  
Cohesive Failure ◽  
Metal Interface ◽  
Cohesive Fracture ◽  
Micro Patterning ◽  
Polymer Metal ◽  
Metal Interfaces ◽  
Point Bend

It is Common Practice for Polymer-Metal Interfaces, Frequently Encountered in Microelec-Tronic Devices, to Improve Adhesion by Surface Roughening or Micro-Patterning. the Competitionbetween Adhesive Fracture and Cohesive Fracture in the Vicinity of a Patterned Interface, i.e., Inter-Face Crack Deflection, is One of these Key Mechanisms that Contribute Significantly to the Macroscopicadhesion. in this Paper, these Fracture Phenomena are Described Simultaneously by Cohesive Zoneelements with an Exponential Traction-Separation Law (TSL) for the Adhesive Failure and an Initiallyrigid, Exponentially Decaying, TSL for the Cohesive Failure. it is Demonstrated that the Conditions Atwhich Crack Kinking Occurs are Dominated by Fracture Strength Values as Opposed to the Commonlyused Fracture Toughness Values. Experimental Verification is Performed by Means of Four Point Bend-Ing Tests on Specifically Designed Micro-Patterned Polymer-Metal Samples.

Sign in / Sign up

Export Citation Format

Share Document