scholarly journals Fluctuation and extinction of laminar diffusion flame induced by external acoustic wave and source

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Caiyi Xiong ◽  
Yanhui Liu ◽  
Haoran Fan ◽  
Xinyan Huang ◽  
Yuji Nakamura
Keyword(s):  
Acoustic Wave ◽  
Sound Source ◽  
Sound Pressure ◽  
Fire Suppression ◽  
Sound Field ◽  
Extinction Limit ◽  
Laminar Diffusion ◽  
Sound Environment ◽  
Local Sound ◽  
Better Than

AbstractAcoustic wave can destabilize the flame and has a potential in firefighting, but the influences of the sound source and its frequency are still poorly understood. This work applies a loudspeaker to extinguish a laminar diffusion propane flame of 5–25 mm high, where the local sound frequency is 50–70 Hz and sound pressure is 0.8–3.2 Pa (92.0–104.1 dB). Results reveal a constant flame pulsating displacement at the extinction limit, independent of the sound environment used. Such a flame pulsating displacement is found to be caused by the motion of the speaker membrane (or diaphragm) and its induced wind, which could be two orders of magnitude larger than the displacement of the air that transmits acoustic wave. Thus, under the influence of sound source, a critical flame strain rate, stretched by the pulsating airflow, can be formulated to characterize the blow-off limit better than the local sound pressure. The sound source with a lower frequency can produce larger pulsating displacements of both membrane and flame, and thus promoting extinction. This work improves the understanding of flame dynamics under the external sound field and source, and it helps establish a scientific framework for acoustic-based fire suppression technologies.

Ghost Image Suppression Based on Particle Swarm Optimization-MVDR in Sound Field Reconstruction

2015 ◽  
Vol 137 (3) ◽  
Author(s):  
Min Li ◽  
Long Wei ◽  
Qiang Fu ◽  
Debin Yang
Keyword(s):  
Sound Source ◽  
Sound Pressure ◽  
Microphone Array ◽  
Sound Field ◽  
Distribution Map ◽  
Swarm Optimization ◽  
Field Reconstruction ◽  
Grating Lobe ◽  
Sound Field Reconstruction ◽  
Ghost Images

In sound field reconstruction, spurious sources called ghost images always appear around the position of the real sound source in the sound pressure distribution map because of the grating and side lobes, thus resulting in an incorrect identification of the sound source. To solve this problem, a method for suppressing ghost images is proposed in this paper; such method is based on particle swarm optimization (PSO) and minimum variance distortionless response (MVDR) beamforming. In this method, the elements distribution of a microphone array is first optimized by the PSO algorithm to acquire the optimal design of an unequal spacing microphone array. With this array, the grating lobe is suppressed, and the increscent value of the inherent side lobe value is reduced. Second, MVDR algorithm is used to weaken the effect of the side lobes and to obtain a sound pressure distribution map in which the ghost images are suppressed. The advantage of this method is the combination of the unequal spacing array, which suppresses the grating lobe, and the MVDR algorithm, which has excellent performance in spatial filtering. Through this method, a microphone array with a few number of elements can achieve ghost image suppression. Experiments on sound field reconstruction in an anechoic chamber for a single-tone sound source are conducted to validate the proposed method. Moreover, some extra sound field reconstructions for a single-tone sound source and double sound sources with broadband in a normal room with different parameters such as the array shape and distance from the sources to the array are conducted to discuss their influences on the effectiveness of the proposed method.

Research on the Planar Near-Field Acoustic Holography for Cyclostationary Sound Field

2011 ◽  
Vol 105-107 ◽  
pp. 164-167
Author(s):  
Zhi Min Chen ◽  
Hai Chao Zhu ◽  
Rong Fu Mao
Keyword(s):  
Spectral Density ◽  
Physical Quantity ◽  
Sound Source ◽  
Sound Pressure ◽  
Near Field ◽  
Sound Field ◽  
Rotating Machines ◽  
Carrier Wave ◽  
Acoustic Holography ◽  
Complex Sound

The conventional planar near-field acoustic holography is not suitable for cyclostationary sound field radiated by the rotating machines. When the cyclic spectral density (CSD), instead of the complex sound pressure, is adopted as reconstructed physical quantity, the modulating wave and carrier wave components of the cyclostationary sound field can be extracted exactly and so the cyclostationary planar near-field acoustic holography (CPNAH) technique was proposed. Simulation and experimental results show that the modulation characteristics of the cyclostationary sound field can be extracted effectively and the sound source can be localized accurately.

Single-unit selectivity to azimuthal direction and sound pressure level of noise bursts in cat high-frequency primary auditory cortex

1990 ◽  
Vol 63 (6) ◽  
pp. 1448-1466 ◽  
Author(s):  
T. J. Imig ◽  
W. A. Irons ◽  
F. R. Samson
Keyword(s):  
Auditory Cortex ◽  
Sound Pressure Level ◽  
Sound Source ◽  
Single Unit ◽  
Sound Pressure ◽  
Free Field ◽  
Sound Field ◽  
Primary Auditory Cortex ◽  
Pressure Level ◽  
Broadband Noise

1. The azimuth and sound pressure level (SPL) selectivities of single-unit responses recorded in primary auditory cortex of barbiturate-anesthetized cats were studied by the use of broadband noise bursts delivered in the free field from a moveable loud-speaker. The experiments were carried out with cats located inside a quasianechoic sound-isolation chamber. We studied 71 units with relatively stable response properties. All units were located in the frequency representation between 5.8 and 31 kHz. The data obtained for each unit were displayed as an azimuth-level response area, a contour plot that displays the distribution of response magnitude as a joint function of SPL and azimuth at 0 degrees elevation. From these, azimuth and level functions were obtained to derive descriptors of azimuth and level selectivity. 2. Sensitivity to sound-source azimuth was assessed from the modulation of the average azimuth function (average of azimuth functions obtained to each SPL of noise that was presented) for each unit. The sample was arbitrarily divided into a high-directionality (HD) group (66%) whose average azimuth functions had modulation values of greater than or equal to 75% and a low-directionality (LD) group (34%). The distinction between HD and LD groups was made so that we could analyze the characteristics of units likely to be involved in the representation of sound-source azimuth. 3. There is an overrepresentation of the contralateral sound field and the midline in the sample of HD units. The preferred sector for each unit was defined as the range of azimuths within the frontal sound field throughout which unit response was greater than or equal to 75% of maximum. Each unit was classified as either midline preferring (17%, the midpoint of the preferred sector, i.e., best azimuth, was located within 5 degrees of the midline), contralateral preferring (60%), or ipsilateral preferring (23%). The ratio of contralateral- to ipsilateral-preferring units was 2.5:1. A higher proportion of units had best azimuths located in the 10 degrees sector centered on the midline than in any other 10 degrees sector of the frontal sound field. 4. In one animal, recordings were obtained at seven closely spaced sites in layer IV from single- and multiunit responses, which were narrowly tuned to both azimuth and SPL. The units located along a 1-mm length of an isofrequency strip were tuned to similar frequencies and SPLs but had five distinctly different directional preferences distributed throughout the entire frontal sound field.(ABSTRACT TRUNCATED AT 400 WORDS)

scholarly journals Interior Sound Field Subjective Evaluation Based on the 3D Distribution of Sound Quality Objective Parameters and Sound Source Localization

Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 429
Author(s):  
Jiangming Jin ◽  
Hao Cheng ◽  
Tianwei Xie ◽  
Huancai Lu
Keyword(s):  
Source Localization ◽  
Sound Source ◽  
Sound Pressure ◽  
Low Frequency ◽  
Sound Field ◽  
Sound Quality ◽  
Sound Source Localization ◽  
Frequency Noise ◽  
Sound Sources ◽  
Quality Objective

Controlling low frequency noise in an interior sound field is always a challenge in engineering, because it is hard to accurately localize the sound source. Spherical acoustic holography can reconstruct the 3D distributions of acoustic quantities in the interior sound field, and identify low-frequency sound sources, but the ultimate goal of controlling the interior noise is to improve the sound quality in the interior sound field. It is essential to know the contributions of sound sources to the sound quality objective parameters. This paper presents the mapping methodology from sound pressure to sound quality objective parameters, where sound quality objective parameters are calculated from sound pressure at each specific point. The 3D distributions of the loudness and sharpness are obtained by calculating each point in the entire interior sound field. The reconstruction errors of those quantities varying with reconstruction distance, sound frequency, and intersection angle are analyzed in numerical simulation for one- and two-monopole source sound fields. Verification experiments have been conducted in an anechoic chamber. Simulation and experimental results demonstrate that the sound source localization results based on 3D distributions of sound quality objective parameters are different from those based on sound pressure.

Active control of the scattered radiation with a reflecting surface

2019 ◽  
Vol 67 (3) ◽  
pp. 190-196
Author(s):  
Ning Han
Keyword(s):  
Control System ◽  
Active Control ◽  
Scattered Radiation ◽  
Sound Pressure ◽  
Sound Field ◽  
Control Area ◽  
Mirror Image ◽  
Three Dimension ◽  
Control Effect ◽  
Reflecting Surface

Based on a prediction method of the scattered sound pressure, an active control system was proposed in previous work for the three-dimension scattered radiation, where all the relevant simulations and experiments were implemented in three-dimensional free sound field. However, for practical applications, such as the anti-eavesdropping system or the stealth system for submarines, the sound field conditions are usually complex, and the most common case is the one with reflecting surface. It is questionable whether the previous control system is still effective in non-free sound field, or what improvements should be operated to ensure the control effect. In this article, based on the mirror image principle, two methods of calculating the control source strengths are proposed for the scattered radiation control, and numerical simulations with one-channel and multi-channel system are implemented to detect the corresponding control effect. It is seen that the local active control for the scattered radiation is still effective, and the reduction of the sound pressure level as well as the control area is extended with the increasement of the error sensors and control sources.

scholarly journals Research on the Manufacturing Quality of Co-Cured Hat-Stiffened Composite Structure

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2747
Author(s):  
Xiangwen Ju ◽  
Jun Xiao ◽  
Dongli Wang ◽  
Cong Zhao ◽  
Xianfeng Wang
Keyword(s):  
Composite Structures ◽  
Sound Pressure ◽  
Integration Method ◽  
Complex Geometry ◽  
Sound Field ◽  
Thickness Measurement ◽  
Curing Process ◽  
The Finite Element Method ◽  
Manufacturing Quality

The stringer-stiffened structure is widely used due to its excellent mechanical properties. Improving the manufacturing quality of stringer-stiffened structure which have complex geometry is important to ensure the bearing capacity of aviation components. Herein, composite hat-stiffened composite structures were manufactured by different filling forms and bladders with various properties, the deformation of silicone rubber bladder in co-curing process was studied by using the finite element method. The thickness measurement at different positions of the hat-stiffened structure was performed to determine the best filling form and bladder property. Moreover, in view of the detection difficulties in R-zone of stringer, numerical simulation was performed to get the sound pressure and impulse response of at the R-zone of stringer by Rayleigh integration method, and an effective equipment which could stably detect the manufacturing quality of R-zone was designed to verify the correctness of sound field simulation and realize the detection of stringer. With the optimum filling form and bladder properties, hat-stiffened composites can be manufactured integrally with improved surface quality and geometric accuracy, based on co-curing process.

scholarly journals Mathematical modeling and experimental study on solid–liquid suspension separation in ultrasonic standing wave field

2021 ◽  
pp. 146134842110229
Author(s):  
Yajing Wang ◽  
Liqun Wu ◽  
Yaxing Wang ◽  
Yafei Fan
Keyword(s):  
Standing Wave ◽  
Sound Pressure ◽  
Acoustic Radiation ◽  
Sound Field ◽  
Radiation Force ◽  
High Energy ◽  
Factors Affecting ◽  
Liquid Suspension ◽  
Ultrasonic Standing Wave ◽  
Solid Liquid

A new method of removing waste chips is proposed by focusing on the key factors affecting the processing quality and efficiency of high energy beams. Firstly, a mathematical model has been established to provide the theoretical basis for the separation of solid–liquid suspension under ultrasonic standing wave. Secondly, the distribution of sound field with and without droplet has been simulated. Thirdly, the deformation and movement of droplets are simulated and tested. It is found that the sound pressure around the droplet is greater than the sound pressure in the droplet, which can promote the separation of droplets and provide theoretical support for the ultrasonic suspension separation of droplet; under the interaction of acoustic radiation force, surface tension, adhesion, and static pressure, the droplet is deformed so that the gas fluid around the droplet is concentrated in the center to achieve droplet separation, and the droplet just as a flat ball with a central sag is stably suspended in the acoustic wave node.

scholarly journals A Case Study on Soundscape Analysis for the Historical and Ethnic Village of Dong Nationality in Zhaoxing County

Acoustics ◽  
2021 ◽  
Vol 3 (2) ◽  
pp. 221-234
Author(s):  
Zhiyong Deng ◽  
Kexin Dong ◽  
Danfeng Bai ◽  
Kaicheng Tong ◽  
Aili Liu
Keyword(s):  
Sound Pressure ◽  
Subjective Experience ◽  
Guizhou Province ◽  
Music Listening ◽  
Ethnic Music ◽  
Curve Fit ◽  
Sound Event ◽  
Sound Environment ◽  
Independent Variable

A soundscape is a sound environment of the awareness of auditory perception and social or cultural understandings. Based on a soundscape investigation in 2019 in the historical and ethnic village of Dong Nationality in Zhaoxing County, Guizhou Province of China, a case study on the soundscape analysis with the acoustical sound pressure level and an impressive sound event or soundmark is introduced in this paper. Furthermore, in order to determine the subjective soundscape experience and its influence by the length of background music listening, the independent variable “Length of Listening” and six adjective pairs, such as “Monotonous” to “Rich”, “Clamorous” to “Quiet”, “Stressing” to “Relaxing”, “Boring” to “Vivid”, “Noisy” to “Musical” and “Disliked” to “Preferable” are chosen to obtain a curve-fit, which shows that the length of the music listening background has a higher correlation to the subjective experience, and no sufficient attention has been paid to the context of the traditional soundscape preservation, ethnic music and quiet and soft ambient sounds.

Study on Sound Field of High Intensity Focused Ultrasound with Short Focal Length

2012 ◽  
Vol 195-196 ◽  
pp. 364-369 ◽  
Author(s):  
Jin Hua Zhao ◽  
Li Li Yu ◽  
Chun Hui ◽  
Bin Feng Huang ◽  
Chao Li ◽  
...  
Keyword(s):  
Nonlinear Effect ◽  
Sound Pressure ◽  
Focal Length ◽  
Sound Field ◽  
High Intensity Focused Ultrasound ◽  
Beam Equation ◽  
Focal Region ◽  
Interface Position ◽  
Short Focal Length ◽  
Planar Wave

In this paper, numerical simulation of sound field with short focal length is performed, which is based on spheroidal beam equation (SBE) in frequency-domain for transducer with a wide aperture angle. And we made some experiments on vitro bovine liver to explore the characteristic of sound pressure and-3dB sound focal region at different positions of incident interface. It is found that with a fixed curvature radius if the focal length is shorter under the skin, the amplitude of sound pressure will be higher on the focus and the shape of-3dB sound focal region will be smaller. When the incident interface is in the range of planar wave, nonlinear effect is strong and the focus will change with the interface position. Especially when the position is near to transition location between planar wave and spheroidal wave, the nonlinear effect is lowered. While the focus is closer to the sound source so as to burn the scarfskin easily. When the interface is in the range of spheroidal wave, the focus position changes little but the side lobe effect due to refraction is obvious. And the focusing performance of transducer will be affected. The experimental results validate the accuracy of theoretical results. It is concluded that the position of incident interface should be selected reasonably with short focal length in the treatment of superficial tissue.

Synthetic individual binaural audio delivery by pinna image processing

2014 ◽  
Vol 10 (3) ◽  
pp. 239-254 ◽  
Author(s):  
Simone Spagnol ◽  
Michele Geronazzo ◽  
Davide Rocchesso ◽  
Federico Avanzini
Keyword(s):  
Sound Source ◽  
Low Complexity ◽  
Head Orientation ◽  
Sound Sources ◽  
Content Type ◽  
Localization Test ◽  
Subjective Measurements ◽  
Head Related Transfer Function ◽  
Practical Implications ◽  
Better Than

Purpose – The purpose of this paper is to present a system for customized binaural audio delivery based on the extraction of relevant features from a 2-D representation of the listener’s pinna. Design/methodology/approach – The most significant pinna contours are extracted by means of multi-flash imaging, and they provide values for the parameters of a structural head-related transfer function (HRTF) model. The HRTF model spatializes a given sound file according to the listener’s head orientation, tracked by sensor-equipped headphones, with respect to the virtual sound source. Findings – A preliminary localization test shows that the model is able to statically render the elevation of a virtual sound source better than non-individual HRTFs. Research limitations/implications – Results encourage a deeper analysis of the psychoacoustic impact that the individualized HRTF model has on perceived elevation of virtual sound sources. Practical implications – The model has low complexity and is suitable for implementation on mobile devices. The resulting hardware/software package will hopefully allow an easy and low-tech fruition of custom spatial audio to any user. Originality/value – The authors show that custom binaural audio can be successfully deployed without the need of cumbersome subjective measurements.

Sign in / Sign up

Export Citation Format

Share Document