Controllable synthesis of hollow mesoporous silica particles by a facile one-pot sol–gel method

2015 ◽  
Vol 51 (52) ◽  
pp. 10517-10520 ◽  
Author(s):  
Jing-Chuan Song ◽  
Fei-Fei Xue ◽  
Zhong-Yuan Lu ◽  
Zhao-Yan Sun
Keyword(s):  
Particle Size ◽  
Mesoporous Silica ◽  
Shell Thickness ◽  
Sol Gel ◽  
Silica Particles ◽  
Controllable Synthesis ◽  
One Pot ◽  
Gel Method ◽  
Sol Gel Method ◽  
Hollow Mesoporous Silica

A simple and facile one-pot sol–gel method is proposed for the fabrication of hollow mesoporous silica particles. Both the particle size and the shell thickness can be well controlled.

Annealing Effects on the Physical and Magnetic Properties of Tb1.5Y1.5Fe5O12 Films Nanoparticles Prepared by Sol-Gel Method

2013 ◽  
Vol 756 ◽  
pp. 91-98 ◽  
Author(s):  
Ftema W. Aldbea ◽  
Noor Bahyah Ibrahim ◽  
Mustafa Hj. Abdullah
Keyword(s):  
Particle Size ◽  
Magnetic Properties ◽  
Annealing Temperature ◽  
Quartz Substrate ◽  
Sol Gel ◽  
Lattice Parameter ◽  
Gel Method ◽  
X Ray ◽  
Sol Gel Method ◽  
Iron Garnet

Terbium –substituted yttrium iron garnet (Tb1.5Y1.5Fe5O12) films nanoparticles were successfully prepared by a sol-gel method. The films were deposited on the quartz substrate using spin coating technique. To study effect of annealing temperature, the annealing process was executed at 700, 800 and 900 °C in air for 2 hours. The X-ray diffraction (XRD) proved that the pure phase of garnet structure was detected for the film annealed at 900 °C. The lattice parameter increased with the increment of annealing temperature and the highest value of 12.35 Å was obtained at 900 °C. Field Emission Scanning Electron Microscope (FE-SEM) results showed that the particle size increased from 43nm to 56nm as annealing temperature increased from 700 to 900°C. The film’s thickness also affected by increasing of annealing temperature and become thin at 900 °C due to densification process occurred at high annealing temperature. The elemental compositions of the Tb1.5Y1.5Fe5O12 film were detected using an Energy Dispersive X-raySpectroscopy (EDX). Magnetic properties at room temperature were measured using a Vibrating Sample Magnetometer (VSM).The saturation magnetization Ms increased with the annealingtemperature and showed a high value of 104emu/cm3, but the coercivity Hc of the film was decreased due to the increment of the particle size. Normal 0 21 false false false MS X-NONE X-NONE MicrosoftInternetExplorer4 Terbium –substituted yttrium iron garnet (Tb1.5Y1.5Fe5O12) films nanoparticles were successfully prepared by a sol-gel method. The films were deposited on the quartz substrate using spin coating technique. To study effect of annealing temperature, the annealing process was executed at 700, 800 and 900°C in air for 2 hours. The X-ray diffraction (XRD) proved that the pure phase of garnet structure was detected for the film annealed at 900 °C. The lattice parameter increased with the increment of annealing temperature and the highest value of 12.35 Å was obtained at 900 °C. Field Emission Scanning Electron Microscope (FE-SEM) results showed that the particle size increased from 43nm to 56nm as annealing temperature increased from 700 to 900 °C. The film’s thickness also affected by increasing of annealing temperature and become thin at 900 °C due to densification process occurred at high annealing temperature. The elemental compositions of the Tb1.5Y1.5Fe5O12 film were detected using an Energy Dispersive X-ray Spectroscopy (EDX). Magnetic properties at room temperature were measured using a Vibrating Sample Magnetometer (VSM).The saturation magnetization Ms increased with the annealing temperature and showed a high value of 104emu/cm3, but the coercivity Hc of the film was decreased due to the increment of the particle size. st1\:*{behavior:url(#ieooui) } /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;}

Performance of Polishing Slurries containing Silica Particles grown by Sol-Gel Method

2000 ◽  
Vol 613 ◽  
Author(s):  
Sun Hyuk Bae ◽  
Jae-Hyun So ◽  
Seung-Man Yang ◽  
Do Hyun Kim
Keyword(s):  
Fumed Silica ◽  
Sol Gel ◽  
Particle Growth ◽  
Silica Particles ◽  
Gel Method ◽  
Sol Gel Method ◽  
Irregular Shapes ◽  
Wafer Polishing ◽  
Transmission Electron ◽  
Silica Slurry

ABSTRACTSilica slurry used as abrasives in wafer polishing process is made by dispersing silica particles in an alkali solution. Since commercially available colloidal or fumed silica particles need some modifications to be directly used as abrasive slurry due to their small sizes, irregular shapes or broad size distribution, we have prepared silica abrasives by particle growth of fumed silica or colloidal silica as seeds by sol-gel method. Silica slurries prepared by this step-wise growth from commercial seeds were tested using one-armed polisher for the comparison with commercial slurries and showed the performance comparable to commercial slurries. Microstructures of polishing slurries were investigated using transmission electron microscopy and ARES rheometer. From the result, stability of the slurry was found to be more important than the primary particle sizes for the polishing performance.

scholarly journals Synthesis of Spherical Silica by Sol-Gel Method and Its Application as Catalyst Support

2011 ◽  
Vol 10 (2) ◽  
pp. 25
Author(s):  
Anirut Leksomboon ◽  
Bunjerd Jongsomjit
Keyword(s):  
Particle Size ◽  
Ethylene Glycol ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Sol Gel ◽  
Weight Ratio ◽  
Gel Method ◽  
Sol Gel Method ◽  
Spherical Silica

In this present study, the spherical silica support was synthesized from tetraethyloxysilane (TEOS), water, sodium hydroxide, ethylene glycol and n-dodecyltrimethyl ammonium bromide (C12TMABr). The particle size was controlled by variation of the ethylene glycol co-solvent weight ratio of a sol-gel method preparation in the range of 0.10 to 0.50. In addition, the particle size apparently increases with high weight ratio of co-solvent, but the particle size distribution was broader. The standard deviation of particle diameter is large when the co-solvent weight ratio is more than 0.35 and less than 0.15. However, the specific surface area was similar for all weight ratios ranging from 1000 to 1300 m2/g. The synthesized silica was spherical and has high specific surface area. The cobalt was impregnated onto the obtained silica to produce the cobalt catalyst used for CO2 hydrogenation.</

Preparation of La0.75Sr0.25Cr0.5Mn0.5O3-δ Nanometer Powders by Sol-Gel Method and Research about its Electrochemical Performance

2013 ◽  
Vol 712-715 ◽  
pp. 257-261
Author(s):  
Yin Lin Wu ◽  
Qing Hui Wang ◽  
Ling Wang ◽  
Hai Yan Zhao
Keyword(s):  
Heat Treatment ◽  
Particle Size ◽  
Electrochemical Performance ◽  
Heat Treatment Temperature ◽  
Sol Gel ◽  
Treatment Temperature ◽  
Preparation Process ◽  
Gel Method ◽  
Sol Gel Method ◽  
Ft Ir

The La0.75Sr0.25Cr0.5Mn0.5O3-δnanometer powders were prepared by citric acid sol-gel method.The samples were characterized by DTA, FT-IR, XRD, TEM techniques. The preparation process, morphology of synthesized powders, the best heat-treatment temperature and the electrochemical performance had been studied. The results show that the spherical nanometer powders can be obtained and the best heat-treatment temperature is 800°C. The particle size is about 30nm and Ea is 0.071 eV.

scholarly journals Catalytic myrtenol amination over gold, supported on alumina doped with ceria and zirconia

2018 ◽  
Vol 5 (1) ◽  
pp. 49-58 ◽  
Author(s):  
Yu.S. Demidova ◽  
I.L. Simakova ◽  
E.V. Suslov ◽  
K.P. Volcho ◽  
N.F. Salakhutdinov ◽  
...  
Keyword(s):  
Metal Oxides ◽  
Sol Gel ◽  
Gold Catalyst ◽  
Catalyst Support ◽  
Acid Sites ◽  
One Pot ◽  
Gel Method ◽  
Sol Gel Method ◽  
Alcohol Activation ◽  
The One

Abstract In the current work gold catalysts supported on both commercial oxides and oxides synthesized by the sol-gel method were used for the one-pot alcohol amination of myrtenol. In general, utilization of metal oxides synthesized by the sol-gel method as the gold catalyst support enhanced the knowledge regarding key parameters determining catalytic behavior. Synthesized alumina was characterized by stronger acid sites favoring primary amine accumulation on the catalyst surface, as compared to the commercial oxide. Utilization of mixed metal oxides synthesized by the sol-gel method resulted in the non-additive behavior of different oxides enhancing the catalytic activity. Introduction of ceria into alumina modified the support basicity resulting in more efficient alcohol activation.

The Influence of Water Content on the Growth of the Hybrid-Silica Particles by Sol-Gel Method

Silicon ◽  
2020 ◽  
Author(s):  
Xijia Zhao ◽  
Yihan Wang ◽  
Jianhui Luo ◽  
Pingmei Wang ◽  
Peiwen Xiao ◽  
...  
Keyword(s):  
Water Content ◽  
Sol Gel ◽  
Silica Particles ◽  
Gel Method ◽  
Sol Gel Method ◽  
Hybrid Silica ◽  
Influence Of Water

Controlled synthesis and enhanced photoelectro-catalytic activity of a 3D TiO2 nanotube array/TiO2 nanoparticle heterojunction using a combined dielectrophoresis/sol–gel method

2019 ◽  
Vol 7 (17) ◽  
pp. 4981-4987 ◽  
Author(s):  
Ruiyu Bao ◽  
Chen Chen ◽  
Jianxin Xia ◽  
Huiying Chen ◽  
Hua Li
Keyword(s):  
Particle Size ◽  
Catalytic Activity ◽  
Surface Morphology ◽  
Sol Gel ◽  
Tio2 Nanoparticle ◽  
Controlled Synthesis ◽  
Tio2 Nanotube Array ◽  
Nanotube Array ◽  
Gel Method ◽  
Sol Gel Method

The surface morphology and particle size of materials can be controlled using DEP technology.

Preparation and Performance of Porous Membrane Materials Using the Sol-Gel Method

2010 ◽  
Vol 33 ◽  
pp. 251-253
Author(s):  
Peng Zhang ◽  
Gang Chen ◽  
Bin Guo ◽  
Shu Kang Cheng
Keyword(s):  
Sol Gel ◽  
Porous Membrane ◽  
Silica Particles ◽  
High Tech ◽  
Experimental Conditions ◽  
Preparation Methods ◽  
Gel Method ◽  
Membrane Materials ◽  
Sol Gel Method ◽  
And Performance

Porous membrane materials have the universal use, so it is widely considered as one of the most promising high-tech. Different membranes have different preparation methods. In this paper, the sol-gel method was applied to prepare silica particles using ammonia as catalyst of TEOS hydrolysis, then silica particles were mixed with polyethylene, and finally silica particles were dissolved with hydrofluoric acid, leaving holes, the porous materials were obtained. The results show that: (1) In this experimental conditions, the size of silica particles are closely related to the water content of the system. (2) The size of silica particles affects the agglomeration of particles. The size of silica particles are smaller, the agglomeration is more obvious. (3) As the content of PE increases, the porosity of the samples decreases continuously; in theory, when the content of silica is low, the hole will be greater.

Sign in / Sign up

Export Citation Format

Share Document