scholarly journals Large-area electrospray-deposited nanocrystalline CuXO hole transport layer for perovskite solar cells

RSC Advances ◽  
2017 ◽  
Vol 7 (74) ◽  
pp. 46651-46656 ◽  
Author(s):  
Ian Y. Y. Bu ◽  
Yaw-Shyan Fu ◽  
Jian-Fu Li ◽  
Tzung-Fang Guo
Keyword(s):  
Spray Deposition ◽  
Perovskite Solar Cells ◽  
Cost Effective ◽  
Hole Transport ◽  
Transport Layer ◽  
Hole Transport Layer ◽  
Large Area ◽  
Perovskite Layer ◽  
Electrostatic Spray Deposition ◽  
Cost Effective Approach

In this study, a fully scalable and cost-effective approach for fabricating PSCs using the combination of direct electrostatic spray deposition for (HTL and perovskite layer) and thermal evaporation on conductive substrates.

scholarly journals Device Modeling and Design of Inverted Solar Cell Based on Comparative Experimental Analysis between Effect of Organic and Inorganic Hole Transport Layer on Morphology and Photo-Physical Property of Perovskite Thin Film

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2191
Author(s):  
Xiaolan Wang ◽  
Xiaoping Zou ◽  
Jialin Zhu ◽  
Chunqian Zhang ◽  
Jin Cheng ◽  
...  
Keyword(s):  
Light Absorption ◽  
Short Circuit ◽  
Perovskite Solar Cells ◽  
Open Circuit ◽  
Hole Transport ◽  
Transport Layer ◽  
Hole Transport Layer ◽  
Functional Layer ◽  
Perovskite Layer ◽  
The Impact

It is crucial to find a good material as a hole transport layer (HTL) to improve the performance of perovskite solar cells (PSCs), devices with an inverted structure. Polyethylene dioxythiophene-poly (styrene sulfonate) (PEDOT:PSS) and inorganic nickel oxide (NiOx) have become hotspots in the study of hole transport materials in PSCs on account of their excellent properties. In our research, NiOx and PEDOT: PSS, two kinds of hole transport materials, were prepared and compared to study the impact of the bottom layer on the light absorption and morphology of perovskite layer. By the way, some experimental parameters are simulated by wx Analysis of Microelectronic and Photonic Structures (wxAMPS). In addition, thin interfacial layers with deep capture levels and high capture cross sections were inserted to simulate the degradation of the interface between light absorption layer and PEDOT:PSS. This work realizes the combination of experiment and simulation. Exploring the mechanism of the influence of functional layer parameters plays a vital part in the performance of devices by establishing the system design. It can be found that the perovskite film growing on NiOx has a stronger light absorption capacity, which makes the best open-circuit voltage of 0.98 V, short-circuit current density of 24.55 mA/cm2, and power conversion efficiency of 20.01%.

scholarly journals CuI/Spiro-OMeTAD Double-Layer Hole Transport Layer to Improve Photovoltaic Performance of Perovskite Solar Cells

Coatings ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 978
Author(s):  
Chaoqun Lu ◽  
Weijia Zhang ◽  
Zhaoyi Jiang ◽  
Yulong Zhang ◽  
Cong Ni
Keyword(s):  
Solar Cells ◽  
Double Layer ◽  
Photovoltaic Performance ◽  
Perovskite Solar Cells ◽  
Hole Transport ◽  
Transport Layer ◽  
Hole Transport Layer ◽  
Photoelectric Conversion Efficiency ◽  
Photoelectric Conversion ◽  
Perovskite Layer

The hole transport layer (HTL) is one of the main factors affecting the efficiency and stability of perovskite solar cells (PSCs). However, obtaining HTLs with the desired properties through current preparation techniques remains a challenge. In the present study, we propose a new method which can be used to achieve a double-layer HTL, by inserting a CuI layer between the perovskite layer and Spiro-OMeTAD layer via a solution spin coating process. The CuI layer deposited on the surface of the perovskite film directly covers the rough perovskite surface, covering the surface defects of the perovskite, while a layer of CuI film avoids the defects caused by Spiro-OMetad pinholes. The double-layer HTLs improve roughness and reduce charge recombination of the Spiro-OMeTAD layer, thereby resulting in superior hole extraction capabilities and faster hole mobility. The CuI/Spiro-OMeTAD double-layer HTLs-based devices were prepared in N2 gloveboxes and obtained an optimized PCE (photoelectric conversion efficiency) of 17.44%. Furthermore, their stability was improved due to the barrier effect of the inorganic CuI layer on the entry of air and moisture into the perovskite layer. The results demonstrate that another deposited CuI film is a promising method for realizing high-performance and air-stable PSCs.

scholarly journals Charge extraction via graded doping of hole transport layers gives highly luminescent and stable metal halide perovskite devices

2019 ◽  
Vol 5 (2) ◽  
pp. eaav2012 ◽  
Author(s):  
Mojtaba Abdi-Jalebi ◽  
M. Ibrahim Dar ◽  
Satyaprasad P. Senanayak ◽  
Aditya Sadhanala ◽  
Zahra Andaji-Garmaroudi ◽  
...  
Keyword(s):  
Perovskite Solar Cells ◽  
Hole Transport ◽  
Transport Layer ◽  
Continuous Illumination ◽  
Hole Transport Layer ◽  
Perovskite Layer ◽  
Metal Halide Perovskite ◽  
Hole Transport Layers ◽  
Interfacial Defects ◽  
Extended Power

One source of instability in perovskite solar cells (PSCs) is interfacial defects, particularly those that exist between the perovskite and the hole transport layer (HTL). We demonstrate that thermally evaporated dopant-free tetracene (120 nm) on top of the perovskite layer, capped with a lithium-doped Spiro-OMeTAD layer (200 nm) and top gold electrode, offers an excellent hole-extracting stack with minimal interfacial defect levels. For a perovskite layer interfaced between these graded HTLs and a mesoporous TiO2 electron-extracting layer, its photoluminescence yield reaches 15% compared to 5% for the perovskite layer interfaced between TiO2 and Spiro-OMeTAD alone. For PSCs with graded HTL structure, we demonstrate efficiency of up to 21.6% and an extended power output of over 550 hours of continuous illumination at AM1.5G, retaining more than 90% of the initial performance and thus validating our approach. Our findings represent a breakthrough in the construction of stable PSCs with minimized nonradiative losses.

scholarly journals Facile NiOx Sol-Gel Synthesis Depending on Chain Length of Various Solvents without Catalyst for Efficient Hole Charge Transfer in Perovskite Solar Cells

Polymers ◽  
2018 ◽  
Vol 10 (11) ◽  
pp. 1227 ◽  
Author(s):  
Byung Kim ◽  
Woongsik Jang ◽  
Dong Wang
Keyword(s):  
Solar Cells ◽  
Chain Length ◽  
Short Circuit ◽  
Sol Gel ◽  
Perovskite Solar Cells ◽  
Open Circuit ◽  
Hole Transport ◽  
Transport Layer ◽  
Hole Transport Layer ◽  
Perovskite Layer

Nickel oxide (NiOx)–based perovskite solar cells (PSCs) have recently gained considerable interest, and exhibit above 20% photovoltaic efficiency. However, the reported syntheses of NiOx sol-gel used toxic chemicals for the catalysts during synthesis, which resulted in a high-temperature annealing requirement to remove the organic catalysts (ligands). Herein, we report a facile “NiOx sol-gel depending on the chain length of various solvents” method that eschews toxic catalysts, to confirm the effect of different types of organic solvents on NiOx synthesis. The optimized conditions of the method resulted in better morphology and an increase in the crystallinity of the perovskite layer. Furthermore, the use of the optimized organic solvent improved the absorbance of the photoactive layer in the PSC device. To compare the electrical properties, a PSC was prepared with a p-i-n structure, and the optimized divalent alcohol-based NiOx as the hole transport layer. This improved the charge transport compared with that for the typical 1,2-ethanediol (ethylene glycol) used in earlier studies. Finally, the optimized solvent-based NiOx enhanced device performance by increasing the short-circuit current density (Jsc), open-circuit voltage (Voc), and fill factor (FF), compared with those of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate)–based devices.

scholarly journals Efficient Solution Processed CH3NH3PbI3 Perovskite Solar Cells with PolyTPD Hole Transport Layer

2019 ◽  
Vol 74 (8) ◽  
pp. 665-672 ◽  
Author(s):  
Julian Höcker ◽  
David Kiermasch ◽  
Philipp Rieder ◽  
Kristofer Tvingstedt ◽  
Andreas Baumann ◽  
...  
Keyword(s):  
Solar Cells ◽  
Surface Coverage ◽  
Energy Levels ◽  
Perovskite Solar Cells ◽  
Hole Transport ◽  
Transport Layer ◽  
Hole Transport Layer ◽  
Perovskite Layer ◽  
Solvent Engineering ◽  
Highest Occupied Molecular Orbital

AbstractThe organic and hydrophobic polymer poly[N, N′-bis(4-butilphenyl)-N, N′-bis(phenyl)-benzidine] (polyTPD) represents a promising hole transport layer (HTL) for perovskite photovoltaics due to its suitable energy levels, whereby its highest occupied molecular orbital level matches well with the valence band level of methylammonium lead triiodide (CH3NH3PbI3, MAPbI3) perovskite. However, processing a perovskite layer from the solution on the surface of this organic material, is found to be difficult due to the surface properties of the latter. In this study, we evaluate efficient p-i-n type MAPbI3 perovskite solar cells employing differently processed polyTPD layers. We found that the surface coverage of the MAPbI3 perovskite layer strongly depends on the preparation method of the underlying polyTPD layer. By varying the solvents for the polyTPD precursor, its concentration, and by applying an optimised two-step perovskite deposition technique we increased both the surface coverage of the perovskite layer as well as the power conversion efficiency (PCE) of the corresponding solar cell devices. Our simple solvent-engineering approach demonstrates that no further interface modifications are needed for a successful preparation of efficient planar photovoltaic devices with PCEs in the range of 15 %–16 %.

scholarly journals Enhanced Efficiencies of Perovskite Solar Cells by Incorporating Silver Nanowires into the Hole Transport Layer

Micromachines ◽  
2019 ◽  
Vol 10 (10) ◽  
pp. 682 ◽  
Author(s):  
Chien-Jui Cheng ◽  
Rathinam Balamurugan ◽  
Bo-Tau Liu
Keyword(s):  
Solar Cells ◽  
Charge Transfer ◽  
Silver Nanowires ◽  
Perovskite Solar Cells ◽  
Hole Transport ◽  
Transport Layer ◽  
Hole Transport Layer ◽  
Perovskite Layer ◽  
Iodide Ions ◽  
Poly Styrene Sulfonate

In this study, we incorporated silver nanowires (AgNWs) into poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) as a hole transport layer (HTL) for inverted perovskite solar cells (PVSCs). The effect of AgNW incorporation on the perovskite crystallization, charge transfer, and power conversion efficiency (PCE) of PVSCs were analyzed and discussed. Compared with neat PEDOT:PSS HTL, incorporation of few AgNWs into PEDOT:PSS can significantly enhance the PCE by 25%. However, the AgNW incorporation may result in performance overestimation due to the lateral charge transfer. The corrosion of AgNWs with a perovskite layer was discussed. Too much AgNW incorporation may lead to defects on the interface between the HTL and the perovskite layer. An extra PEDOT:PSS layer over the pristine PEDOT:PSS-AgNW layer can prevent AgNWs from corrosion by iodide ions.

scholarly journals Improved efficiency and reduced hysteresis in ultra-stable fully printable mesoscopic perovskite solar cells through incorporation of CuSCN into the perovskite layer

2019 ◽  
Vol 7 (14) ◽  
pp. 8073-8077 ◽  
Author(s):  
Iwan Zimmermann ◽  
Paul Gratia ◽  
David Martineau ◽  
Giulia Grancini ◽  
Jean-Nicolas Audinot ◽  
...  
Keyword(s):  
Solar Cells ◽  
Perovskite Solar Cells ◽  
Hole Transport ◽  
Transport Layer ◽  
Hole Transport Layer ◽  
Perovskite Layer ◽  
Term Stability ◽  
Long Term Stability ◽  
Carbon Based

Improved charge extraction in carbon-based fully printable hole transport layer-free mesoscopic perovskite solar cells with excellent long-term stability.

Homogeneous doping of entire perovskite solar cells via alkali cation diffusion from the hole transport layer

2021 ◽  
Vol 9 (14) ◽  
pp. 9266-9271
Author(s):  
Mengjiong Chen ◽  
Hong Wei Qiao ◽  
Ziren Zhou ◽  
Bing Ge ◽  
Jingjing He ◽  
...  
Keyword(s):  
Alkali Metal ◽  
Perovskite Solar Cells ◽  
Electronic States ◽  
Hole Transport ◽  
Transport Layer ◽  
Electron Transport Layer ◽  
Hole Transport Layer ◽  
Alkali Metal Ions ◽  
Cation Diffusion ◽  
Perovskite Layer

Alkali metal ions spontaneously diffuse from the hole transport layer into perovskite layer and electron transport layer, which could enhance the conductivity of NiOx films and modulate perovskite layer electronic states, simultaneously.

scholarly journals Investigation of the S-Shaped Current–Voltage Curve in High Open-Circuit Voltage Ruddlesden–Popper Perovskite Solar Cells

2021 ◽  
Vol 9 ◽  
Author(s):  
Hong Zhong ◽  
Renlai Zhou ◽  
Xiaoqing Wu ◽  
Xiaoyun Lin ◽  
Ya Wang ◽  
...  
Keyword(s):  
Solar Cells ◽  
Open Circuit Voltage ◽  
Phase Distribution ◽  
Perovskite Solar Cells ◽  
Open Circuit ◽  
Hole Transport ◽  
Transport Layer ◽  
Hole Transport Layer ◽  
Perovskite Layer ◽  
Current Voltage

We report our investigation on the S-shaped current–voltage characteristics in a hot-casting–processed (BA)2 (MA)3Pb4I13 Ruddlesden–Popper (RP) perovskite solar cell. The two-dimensional perovskite solar cells are fabricated with NiOx as the hole transport layer (HTL), which leads to significantly high open-circuit voltage (Voc). The champion device shows a Voc of 1.21 V and a short current density (Jsc) of 17.14 mA/cm2, leading to an overall power conversion efficiency (PCE) of 13.7%. Although the PCE is much higher than the control device fabricated on PEDOT:PSS, a significant S-shaped current–voltage behavior is observed in these NiOx-based devices. It is found that the S-shaped current–voltage behavior is related to the lower dimensional phase distribution and crystallinity at the bottom interface of the RP perovskite layer, and the S-shaped distortion is less severe after the device ageing test.

scholarly journals Composited Film of Poly(3,4-ethylenedioxythiophene) and Graphene Oxide as Hole Transport Layer in Perovskite Solar Cells

Polymers ◽  
2021 ◽  
Vol 13 (22) ◽  
pp. 3895
Author(s):  
Tian Yuan ◽  
Jin Li ◽  
Shimin Wang
Keyword(s):  
Graphene Oxide ◽  
Solar Cells ◽  
Perovskite Solar Cells ◽  
Hole Transport ◽  
Transport Layer ◽  
Hole Transport Layer ◽  
Perovskite Layer ◽  
Hybrid Perovskite ◽  
Polystyrene Sulfonic Acid ◽  
The Cost

It is important to lower the cost and stability of the organic–inorganic hybrid perovskite solar cells (PSCs) for industrial application. The commonly used hole transport materials (HTMs) such as Spiro-OMeTAD, poly[bis(4-phenyl)(2,4,6-trimethylphenyl)amine] (PTAA) and poly(3-hexylthiophene-2,5-diyl) (P3HT) are very expensive. Here, 3,4-ethylenedioxythiophene (EDOT) monomers are in-situ polymerized on the surface of graphene oxide (GO) as PEDOT-GO film. Compared to frequently used polystyrene sulfonic acid (PSS), GO avoids the corrosion of the perovskite and the use of H2O solvent. The composite PEDOT-GO film is between carbon pair electrode and perovskite layer as hole transport layer (HTL). The highest power conversion efficiency (PCE) is 14.09%.

Sign in / Sign up

Export Citation Format

Share Document