Quality factor improvement of MIS capacitor using side metal coating

2018 ◽  
Vol 54 (8) ◽  
pp. 515-517
Author(s):  
S.J. Baek ◽  
J.C. Kim ◽  
J.M. Yook
2018 ◽  
Vol 185 ◽  
pp. 02016 ◽  
Author(s):  
Tatyana Mikhailova ◽  
Alexander Shaposhnikov ◽  
Anatoly Prokopov ◽  
Andrey Karavainikov ◽  
Sergey Tomilin ◽  
...  

New original Tamm plasmon-polaritons (TPP) structures with Bi-substituted iron garnet and Au plasmonic layers were proposed, synthesized and investigated. The structures with single and double garnet layers were modelled to form a TPP mode at the center of photonic band gab. The top Au layer has the gradient thickness varied in the range from 0 to 65.2 nm. It was found the features of TPP resonances as a function of the thickness of metal coating. The resonances on TPP have the maximum optical quality factor and transmission at the vicinity of Au thickness of 30 nm. These configurations are optimum to form the highest intensity of electric field of light wave in the area of the magnetic layers. It was found the spectral blue and red shifts of TPP mode with increasing of Au thickness. The blue and red shifts can be explained respectively by structural and thickness changes of Au coating. The maximum resonant values of Faraday rotation were –2.1° at 664 nm and –12.3° at 645 nm for structures with single and double garnet layers, respectively, and thickness of Au coating of 65.2 nm.


Author(s):  
Klaus-Ruediger Peters

Topographic ultra high resolution can now routinely be established on bulk samples in cold field emission scanning electron microscopy with a second generation of microscopes (FSEM) designed to provide 0.5 nm probe diameters. If such small probes are used for high magnification imaging, topographic contrast is so high that remarkably fine details can be imaged on 2DMSO/osmium-impregnated specimens at ribosome surfaces even without a metal coating. On TCH/osmium-impregnated specimens topographic resolution can be increased further if the SE-I imaging mode is applied. This requires that beam diameter and metal coating thickness be made smaller than the SE range of ~1 nm and background signal contributions be reduced. Subnanometer small probes can be obtained (only) at high accelerating voltages. Subnanometer thin continuous metal films can be produced under the following conditions: self-shadowing effect between metal atoms must be reduced through appropriate deposition techniques and surface mobility of metal atoms must be diminished through high energy sputtering and/or specimen cooling.


Author(s):  
Keiichi Tanaka

With the development of scanning electron microscope (SEM) with ultrahigh resolution, SEM became to play an important role in not only cytology but also molecular biology. However, the preparation methods observing tiny specimens with such high resolution SEM are not yet established.Although SEM specimens are usually coated with metals for getting electrical conductivity, it is desirable to avoid the metal coating for high resolution SEM, because the coating seriously affects resolution at this level, unless special coating techniques are used. For avoiding charging effect without metal coating, we previously reported a method in which polished carbon plates were used as substrate. In the case almost all incident electrons penetrate through the specimens and do not accumulate in them, when the specimens are smaller than 10nm. By this technique some biological macromolecules including ribosomes, ferritin, immunoglobulin G were clearly observed.Unfortunately some other molecules such as apoferritin, thyroglobulin and immunoglobulin M were difficult to be observed only by the method, because they had very low contrast and were easily damaged by electron beam.


Author(s):  
John G. Sheehan

Improvements in particulate coatings for printable paper require understanding mechanisms of colloidal interactions in paper coating suspensions. One way to deduce colloidal interactions is to mage particle spacings and orientations at high resolution with cryo-SEM. Recent improvements in cryo-SEM technique have increased resolution enough to image particles in coating paints,vhich are sometimes smaller than 100 nm. In this report, a metal-coating chamber is described for preparation of colloidal suspensions for cryo-SEM at resolution down to 20 nm. It was found that etching is not necessary to achieve this resolution.A 120 K cryo-SEM sample will remain in an SEM for hours without noticeable condensation of imorphous ice. This is due to the high vapor pressure of vapor-condensed amorphous ice, measured by Kouchi. However, clean vacuum is required to coat samples with the thinnest possible continuous metal films which are required for high magnification SEM. Vapor contaminants, especially hrydrocarbons, are known to interfere with thin-film nucleation and growth so that more metal is needed to form continuous films, and resolution is decreased. That is why the metal-coating chamber in fig. 1 is designed for the cleanest possible vacuum. Feedthroughs for the manipulator md the shutter, which are operated during metal coating, are sealed with leak-proof stainless-steel Dellows. The transfer rod slides through a baseplate feedthrough that is double o-ring sealed.


1988 ◽  
Vol 49 (C8) ◽  
pp. C8-1947-C8-1948
Author(s):  
J. Miltat ◽  
P. Trouilloud

2014 ◽  
Vol 134 (2) ◽  
pp. 26-31 ◽  
Author(s):  
Nguyen Van Toan ◽  
Masaya Toda ◽  
Yusuke Kawai ◽  
Takahito Ono

Sign in / Sign up

Export Citation Format

Share Document