scholarly journals Development of a Method and Algorithm for Inhibiting an Automatic Transfer Switch of the Circuit Breaker for a Sustained Short-Circuit

2020 ◽  
Vol 220 ◽  
pp. 01011
Author(s):  
Igor Nikolaevich Fomin ◽  
Roman Pavlovich Belikov ◽  
Tatyana Anatolyevna Kudinova ◽  
Nailya Kamilevna Miftakhova
Keyword(s):  
Short Circuit ◽  
Circuit Breaker ◽  
Electrical Equipment ◽  
Ring Network ◽  
Circuit Breakers ◽  
Emergency Situations ◽  
Short Circuit Currents

Circuit breakers with automatic transfer switches (ATS) are designed in such a way that when the voltage disappears during a short-circuit (SC) in the ring network line, the ATS device is triggered. At the same time, its switch is turned on at short-circuit, then it is turned off with acceleration. Even a shortterm switching on of the automatic transfer switch for a sustained short-circuit leads to emergency situations [1,2]. The electrical equipment of the ring network spare line is exposed to high emergency short-circuit currents, and the consumers powered by the spare transformer are turned off. It is possible to minimize and eliminate the damages caused by the above mentioned cases by inhibiting the switching on of the circuitbreaker of the automatic transfer switch.

SWITCHING AND LIGHTNING OVERVOLTAGES AND THE REQUIRED WITHSTAND VOLTAGE BETWEEEN THE OPEN CONTACTS OF 245 KV CIRCUIT BREAKERS

2016 ◽  
Vol 63 (0) ◽  
pp. 43-60 ◽  
Author(s):  
Janusz BANDEL ◽  
Artur HEJDUK ◽  
Andrzej DZIERŻYŃSKI ◽  
Piotr KORYCKI ◽  
Henryk SIBILSKI
Keyword(s):  
Short Circuit ◽  
Circuit Breaker ◽  
Dielectric Strength ◽  
Electrical Insulation ◽  
Power Engineering ◽  
Circuit Breakers ◽  
Short Circuit Currents ◽  
Very High ◽  
Single Break

This paper deals with the surges generated in the network during switching operations and lightning surges. The level of both kinds of surge was compared with the required dielectric strength between the open contacts of 245 kV circuit breakers. Overvoltages greater than the electrical withstand voltage of the circuit breaker can cause arc ignition between the circuit breaker’s open contacts and power engineering service s have reported such cases. The results of such failures can be very serious. This is a problem especially for single-break circuit breakers, in which the stresses on the electrical insulation between the open contacts of the breaker are very high. A method for selecting lightning arresters to lower the overvoltages is proposed. The switching of short-circuit currents by a circuit breaker may cause a weakening of the circuit breaker chamber’s insulation and reduce its electrical withstand and durability.

scholarly journals Post-Arc Characteristics of High-Current Arcs in Vacuum Circuit-Breakers

2019 ◽  
Vol 6 (2) ◽  
pp. 170-174
Author(s):  
N. Wenzel ◽  
W. Haas
Keyword(s):  
Short Circuit ◽  
Early Period ◽  
Metal Vapor ◽  
Transverse Magnetic ◽  
High Current ◽  
Electric Resistance ◽  
Circuit Breakers ◽  
Arc Characteristics ◽  
Current Zero ◽  
Short Circuit Currents

The post-arc (PA) characteristics of vacuum arcs in transverse magnetic field contacts are studied for short-circuit currents of up to 123 kA peak and transient recovery voltages below 875 V. The measured PA currents are interpreted in terms of an Electric Resistance Model and the models of Andrews-Varey, Langmuir-Child, and Slepian-Schmelzle. Whereas in the late PA period, the calculations do not agree well with the measurements, the PA behavior is well described in the early period after current-zero. It is concluded that the PA discharge is amplified by ionization of metal vapor particles in the boundary sheath due to electron impact.

scholarly journals Thyristor Arc Eliminator for Protection of Low Voltage Electrical Equipment

Energies ◽  
2019 ◽  
Vol 12 (14) ◽  
pp. 2749 ◽  
Author(s):  
Karol Nowak ◽  
Jerzy Janiszewski ◽  
Grzegorz Dombek
Keyword(s):  
Lower Cost ◽  
Low Voltage ◽  
Short Circuit ◽  
Electrical Equipment ◽  
Power Network ◽  
System Operation ◽  
Test Circuit ◽  
Wide Range ◽  
Short Circuit Currents ◽  
Electrical Apparatus

The paper presents the layout of two opposing thyristors working as an Arc Eliminator (AE). The presented solution makes it possible to protect an electrical apparatus against the effects of an arcing fault. An Arc Eliminator is assumed to be a device cooperating with the protected apparatus. Thyristors were used because of their speed of operation and a relatively lower cost compared to other semiconductors with the same current-carrying capacity. The proposed solution, as one of the few currently available, makes it possible to eliminate the fault arc—both at short-circuit currents and current values to which overcurrent protections do not react. A test circuit was designed and made to study the effectiveness of the thyristor arc eliminator. A series of tests was carried out with variable impedance in the arc branch, including the influence of circuit inductance on arc time. It was found that the thyristor arc eliminator effectively protects devices powered from a low voltage power network against the effects of a fault or arc fault. The correctness of system operation for a wide range of impedance changes in the circuit feeding the arc location was demonstrated.

scholarly journals Arcing Behaviors in the Large-capacity HV SF6 Gas-blast Interrupters

2019 ◽  
Vol 6 (2) ◽  
pp. 140-143 ◽  
Author(s):  
S. A. Averyanova ◽  
E. Tonkonogov
Keyword(s):  
High Voltage ◽  
Short Circuit ◽  
Dielectric Strength ◽  
Numerical Results ◽  
Circuit Breakers ◽  
Large Capacity ◽  
Recovery Processes ◽  
Strength Recovery ◽  
Turbulence Effects ◽  
Short Circuit Currents

A comprehension of the dielectric strength recovery processes during the interruption of short-circuit currents in the high-voltage SF<sub>6</sub> gas-blast circuit breakers is necessary for their modernisation in order to increase the rated voltage and short circuit breaking current per one break. This paper presents numerical results of the turbulence effects on the interruption ability in the SF<sub>6</sub> extinguishing arc chamber.

Investigation of dependences of selectivity of devices of protection against the value of short circuit currents in electrical networks up to 1000 V

2021 ◽  
pp. 98-100
Author(s):  
I. Radko ◽  
◽  
V. Nalivayko ◽  
O. Okushko ◽  
I. Bolbot ◽  
...  
Keyword(s):  
Single Phase ◽  
Modular Design ◽  
Short Circuit ◽  
Electrical Network ◽  
Electrical Networks ◽  
Circuit Breakers ◽  
New Energy ◽  
Short Circuits ◽  
Pole Scheme ◽  
Short Circuit Currents

According to PUE-2017, each group line must be protected against short circuits. Instant disconnection (cut-off) of the line in the event of short circuits provides an electromagnetic release of the circuit breaker. Reliable tripping is possible if the current of a single-phase short circuit is greater than the instantaneous tripping current. Today on the market are widely available circuit breakers with characteristics "B", "C" and "D", which are characterized by different multiplicities of the cut-off current of the electromagnetic release. Some European companies produce circuit breakers with other characteristics, which greatly expands the possibilities protection of electrical equipment. The difficulty in organizing the selectivity of protection is that the circuit breakers of modular design when switching off short circuits are characterized by the same switching time (not more than 0.05 s). The purpose of the research is to find ways to organize the selectivity of protection in electrical networks with voltage up to 1000 V using reliable values of short-circuit currents. In networks with a voltage of up to 1000 V, the current of a single-phase short circuit can be calculated fairly accurately if the exact values of all sections of the electrical network are known. In practice, it is not always possible to obtain reliable data on the numerical characteristics of the 0.4 kV network to which a new energy facility is connected. Therefore, it is proposed to consider part of the network as an active quadrupole, the characteristics of which are obtained by measurements at the point of connection. For further calculations it is necessary to know the voltage at the clamps of the four-pole scheme and the internal impedance. Based on the theory of four-pole scheme, you can get the original data for calculations without calculating the internal parameters of four-poles scheme. Thus, it is proposed to use a hybrid method for estimating the magnitude of probable short-circuit currents in electrical networks up to 1000 V when designing new energy facilities. Credible values of short-circuit currents will allow to organize selective protection of electric networks.

High-voltage electrical equipment in electrical power systems: diagnostics, defects, damage, monitoring

2019 ◽  
Author(s):  
Александр Хренников ◽  
Alexander Khrennikov
Keyword(s):  
Power Systems ◽  
Short Circuit ◽  
Electrical Power ◽  
Electrical Equipment ◽  
Diagnostic Methods ◽  
Power Transformers ◽  
Electrical Power Systems ◽  
The Impact ◽  
Short Circuit Currents ◽  
Detection Of Defects

The analysis of the main methods of diagnostics of electrical equipment for detection of defects and damages in the course of operation is presented. Analysis of the effectiveness of the main diagnostic methods is accompanied by examples of detection of defects and damage to specific equipment: power transformers, reactors, current and voltage transformers, disconnectors, turbogenerators, OPN, etc. Examples of damage and investigation of technological violations of oil-filled transformer-reactor equipment during operation, associated with the loss of electrodynamic resistance of the windings during the flow of through short-circuit currents (short-circuit). The analysis of efficiency of application of methods of diagnostics at detection of defects and damages of power transformers because of the impact of fault current. The questions of electrodynamic tests of power transformers (reactors) for resistance to short-circuit currents, which serve as a tool to improve the reliability of their design, are considered.

scholarly journals О способе увеличения предельно допустимого уровня ударных токов короткого замыкания в электрических контактах

2019 ◽  
Vol 89 (4) ◽  
pp. 614
Author(s):  
А.М. Чалый ◽  
В.А. Дмитриев ◽  
М.А. Павлейно ◽  
О.М. Павлейно ◽  
М.С. Сафонов
Keyword(s):  
Heat Release ◽  
Short Circuit ◽  
Electrical Equipment ◽  
Electrical Contacts ◽  
Recrystallization Temperature ◽  
High Current ◽  
Maximum Permissible Level ◽  
Impulsive Heating ◽  
Pass Through ◽  
Short Circuit Currents

AbstractCurrent passing through electrical contacts causes additional heat release due to the presence of a contact resistance. Heat release in contacts may be considerable. In high-current contacts of high-voltage electrical equipment, the problem of overheating gets worse when fault short-circuit currents pass through the contacts. The maximum permissible level of these currents is limited by heating contact areas to their melting point. Welds due to melting of contacts lead to their failure as a rule. A way of considerably raising maximum permissible short-circuit currents has been suggested. Its idea is impulsive preheating of contacts to a temperature higher than the recrystallization temperature of the contact material. The efficiency of this approach has been confirmed experimentally. Numerical simulation of impulsive heating has been conducted. The results have helped us elaborate recommendations for selecting parameters of a train of current pulses that, acting on a contact, may greatly improve its stability against short-circuit currents.

Sign in / Sign up

Export Citation Format

Share Document