scholarly journals Finite element analysis of heat flow through longitudinal finned tubes in the LNG ambient air vaporizer for a total frost case

2021 ◽  
Vol 323 ◽  
pp. 00020
Author(s):  
Filip Lisowski ◽  
Edward Lisowski
Keyword(s):  
Heat Transfer ◽  
Finite Element ◽  
Natural Gas ◽  
High Efficiency ◽  
Ambient Air ◽  
Element Analysis ◽  
Finned Tubes ◽  
Large Heat ◽  
Flow Through ◽  
Gaseous Form

Liquefied natural gas (LNG) is transported and stored in liquid state at temperature of -163C. In order to use natural gas directly in its gaseous form, LNG must be vaporized, which requires the input of heat. Ambient air vaporizers (AAVs) are commonly used for that purpose in LNG regasification stations. These heat exchangers consist of longitudinally finned tubes with a large heat transfer surface area, provide high efficiency and are virtually cost-free since the heat is taken from the ambient air. This paper presents the results finite element thermal analysis of heat transfer through the finned tubes of ambient air vaporizers under the conditions of total frosting.

scholarly journals Design of longitudinal finned tubes adjusted with the Cesàro curve

2018 ◽  
Vol 27 (48) ◽  
Author(s):  
Luis Eduardo Llano-Sánchez ◽  
Luis Carlos Ruiz ◽  
Darío Manuel Domínguez-Cajeli ◽  
Martha Cecilia Melo-de-Alonso
Keyword(s):  
Heat Transfer ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Smooth Surface ◽  
Transfer Efficiency ◽  
Element Analysis ◽  
Viscous Liquids ◽  
Finned Tubes ◽  
Heat Transfer Efficiency

This paper proposes a process of higher heat transfer efficiency, through a fractal design over Cesàro curve as an extend surface for an exchange tube. Our designs yielded better results applying finite element analysis compared with the smooth surface commonly used in the industry. This new adaptation can be oriented toward applications involving gases and viscous liquids, for devices such as motors, boilers and dissipaters, among others.

Finite Element Modeling for Steel Cord Analysis in Radial Tires

2013 ◽  
Vol 41 (1) ◽  
pp. 60-79 ◽  
Author(s):  
Wei Yintao ◽  
Luo Yiwen ◽  
Miao Yiming ◽  
Chai Delong ◽  
Feng Xijin
Keyword(s):  
Finite Element ◽  
High Efficiency ◽  
Force Measurement ◽  
Three Dimensional ◽  
Local Stress ◽  
Tension Force ◽  
Center Line ◽  
Element Analysis ◽  
Design Variables ◽  
Steel Cord

ABSTRACT: This article focuses on steel cord deformation and force investigation within heavy-duty radial tires. Typical bending deformation and tension force distributions of steel reinforcement within a truck bus radial (TBR) tire have been obtained, and they provide useful input for the local scale modeling of the steel cord. The three-dimensional carpet plots of the cord force distribution within a TBR tire are presented. The carcass-bending curvature is derived from the deformation of the carcass center line. A high-efficiency modeling approach for layered multistrand cord structures has been developed that uses cord design variables such as lay angle, lay length, and radius of the strand center line as input. Several types of steel cord have been modeled using the developed method as an example. The pure tension for two cords and the combined tension bending under various loading conditions relevant to tire deformation have been simulated by a finite element analysis (FEA). Good agreement has been found between experimental and FEA-determined tension force-displacement curves, and the characteristic structural and plastic deformation phases have been revealed by the FE simulation. Furthermore, some interesting local stress and deformation patterns under combined tension and bending are found that have not been previously reported. In addition, an experimental cord force measurement approach is included in this article.

Tire Bead Overheating in Urban Buses and Trucks Using Drum Brake Systems

1998 ◽  
Vol 26 (1) ◽  
pp. 51-62
Author(s):  
A. L. A. Costa ◽  
M. Natalini ◽  
M. F. Inglese ◽  
O. A. M. Xavier
Keyword(s):  
Heat Transfer ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Thermal Energy ◽  
Structural Integrity ◽  
Experimental Temperature ◽  
Temperature Profiles ◽  
Element Analysis ◽  
Drum Brake ◽  
Fea Model

Abstract Because the structural integrity of brake systems and tires can be related to the temperature, this work proposes a transient heat transfer finite element analysis (FEA) model to study the overheating in drum brake systems used in trucks and urban buses. To understand the mechanics of overheating, some constructive variants have been modeled regarding the assemblage: brake, rims, and tires. The model simultaneously studies the thermal energy generated by brakes and tires and how the heat is transferred and dissipated by conduction, convection, and radiation. The simulated FEA data and the experimental temperature profiles measured with thermocouples have been compared giving good correlation.

Probabilistic finite element analysis in heat transfer to a nuclear fuel rod bumper support

2004 ◽  
Vol 218 (12) ◽  
pp. 1499-1505
Author(s):  
Rama Subba Reddy Gorla
Keyword(s):  
Heat Transfer ◽  
Finite Element ◽  
Nuclear Fuel ◽  
Cost Effective ◽  
Distribution Functions ◽  
Cumulative Distribution ◽  
Element Analysis ◽  
Transfer Rates ◽  
Fuel Rod ◽  
Design Variables

Heat transfer from a nuclear fuel rod bumper support was computationally simulated by a finite element method and probabilistically evaluated in view of the several uncertainties in the performance parameters. Cumulative distribution functions and sensitivity factors were computed for overall heat transfer rates due to the thermodynamic random variables. These results can be used to identify quickly the most critical design variables in order to optimize the design and to make it cost effective. The analysis leads to the selection of the appropriate measurements to be used in heat transfer and to the identification of both the most critical measurements and the parameters.

Experimental Platforms and Finite Element Analysis on Hot Stamping Processes

2014 ◽  
Vol 1063 ◽  
pp. 334-338 ◽  
Author(s):  
Tzu Hao Hung ◽  
Heng Kuang Tsai ◽  
Fuh Kuo Chen ◽  
Ping Kun Lee
Keyword(s):  
Heat Transfer ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Process Design ◽  
Hot Stamping ◽  
Boron Steel ◽  
Transfer Coefficients ◽  
Element Analysis ◽  
Heat Transfer Coefficients ◽  
The Finite Element Analysis

Due to the complexity of hot stamping mechanism, including the coupling of material formability, thermal interaction and metallurgical microstructure, it makes the process design more difficult even with the aid of the finite element analysis. In the present study, the experimental platforms were developed to measure and derive the friction and heat transfer coefficients, respectively. The experiments at various elevated temperatures and contact pressures were conducted and the friction coefficients and heat transfer coefficients were obtained. A finite element model was also established with the experimental data and the material properties of the boron steel calculated from the JMatPro software. The finite element simulations for the hot stamping forming of an automotive door beam, including transportation analysis, hot forming analysis and die quenching analysis were then performed to examine the forming properties of the door beam. The validation of the finite element results by the production part confirms the efficiency and accuracy of the developed experimental platforms and the finite element analysis for the process design of hot stamping.

scholarly journals A finite element analysis on combined convection and conduction in a channel with a thick walled cavity

2014 ◽  
Vol 24 (8) ◽  
pp. 1888-1905 ◽  
Author(s):  
M.M. Rahman ◽  
Hakan Oztop ◽  
S. Mekhilef ◽  
R. Saidur ◽  
A. Chamkha ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Finite Element ◽  
Mixed Convection ◽  
Conjugate Heat Transfer ◽  
Transfer Problem ◽  
Thick Wall ◽  
Thermal Conductivity Ratio ◽  
Element Analysis ◽  
Content Type ◽  
Combined Convection

Purpose – The purpose of this paper is to examine the effects of thick wall parameters of a cavity on combined convection in a channel. In other words, conjugate heat transfer is solved. Design/methodology/approach – Galerkin weighted residual finite element method is used to solve the governing equations of mixed convection. Findings – The streamlines, isotherms, local and average Nusselt numbers are obtained and presented for different parameters. It is found heat transfer is an increasing function of dimensionless thermal conductivity ratio. Originality/value – The literature does not have mixed convection and conjugate heat transfer problem in a channel with thick walled cavity.

scholarly journals Influence of Fins Number and Frosting on Heat Transfer through Longitudinal Finned Tubes of LNG Ambient Air Vaporizers

Energies ◽  
2022 ◽  
Vol 15 (1) ◽  
pp. 280
Author(s):  
Filip Lisowski ◽  
Edward Lisowski
Keyword(s):  
Power Supply ◽  
Cryogenic Temperature ◽  
Analytical Approach ◽  
Unit Length ◽  
Heat Rate ◽  
Ambient Air ◽  
Finned Tube ◽  
Ansys Software ◽  
Finned Tubes ◽  
Gaseous Form

The use of cryogenic liquefied gasses in industry is constantly increasing both for process purposes and for power supply needs. The liquefied natural gas (LNG) is stored at cryogenic temperature and its immediate use in gaseous form requires its evaporation. The heat needed to cause a phase change is usually delivered by means of vaporizers. This paper presents a numerical analysis of the influence of the fins number and frost accumulated within the fins surface on the heat transferred through the aluminum finned tubes of LNG ambient air vaporizers. The calculations were carried out applying finite element thermal analysis within Ansys software as well as using an analytical approach. As a result, the heat rate per unit length of the finned tube was obtained. The results were compared for different numbers of longitudinal fins both without frost and for total frosting of the tubes.

Finite Element Analysis about the Influence that High-Speed Motorized Spindle Spindle System Material has on its Temperature Field

2013 ◽  
Vol 712-715 ◽  
pp. 1209-1212 ◽  
Author(s):  
Ke Zhang ◽  
Xiang Nan Ma ◽  
Li Xiu Zhang ◽  
Wen Da Yu ◽  
Yu Hou Wu
Keyword(s):  
Heat Transfer ◽  
Finite Element ◽  
Temperature Field ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
High Speed ◽  
Ceramic Materials ◽  
Motorized Spindle ◽  
Element Analysis ◽  
Finite Element Software

The article has analyzed the changes of temperature of different materials of the spindle, and considered 170SD30 Ceramic Motorized Spindle and the same model Metal Motorized Spindle as the research objects, analyzed the inside heat source and heat transfer mechanism of the high-speed motorized spindle; used finite element software to set up the model of the motorized spindle, and did simulation and analysis. Verified by simulation, heat transfer rate of ceramic materials is slower than the metallic materials, in actual operation of the process, due to different materials have different heat transfer rate, so the temperature distribution of the different materials of motorized spindle are different. This conclusion provides the basis to solve motorized spindle temperature field distribution.

Sign in / Sign up

Export Citation Format

Share Document