scholarly journals Surface roughness influence on the quality factor of high frequency nanoresonators

2008 ◽  
Vol 103 (4) ◽  
pp. 046106 ◽  
Author(s):  
G. Palasantzas
Materials ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3360
Author(s):  
Yakir Dahan ◽  
Eldad Holdengreber ◽  
Elichai Glassner ◽  
Oz Sorkin ◽  
Shmuel E. Schacham ◽  
...  

A new measurement technique of electrical parameters of superconducting thin films at the Very High Frequency (VHF) range is described, based on resonators with microstrip (MS) structures. The design of an optimal resonator was achieved, based on a thorough theoretical analysis, which is required for derivation of the exact configuration of the MS. A theoretical model is presented, from which an expression for the attenuation of a MS line can be derived. Accordingly, simulations were performed, and an optimal resonator for the VHF range was designed and implemented. Production constraints of YBa2Cu3O7 (YBCO) limited the diameter of the sapphire substrate to 3″. Therefore, a meander configuration was formed to fit the long λ/4 MS line on the wafer. By measuring the complex input reflection coefficients of a λ/4 resonator, we extracted the quality factor, which is mainly affected by the dielectric and conductor attenuations. The experimental results are well fitted by the theoretical model. The dielectric attenuation was calculated using the quasi-static analysis of the MS line. An identical copper resonator was produced and measured to compare the properties of the YBCO resonator in reference to the copper one. A quality factor of ~6·105 was calculated for the YBCO resonator, three orders of magnitude larger than that of the copper resonator. The attenuation per unit length of the YBCO layer was smaller by more than five orders of magnitude than that of the copper.


Micromachines ◽  
2021 ◽  
Vol 12 (4) ◽  
pp. 460
Author(s):  
Canbin Zhang ◽  
Chifai Cheung ◽  
Benjamin Bulla ◽  
Chenyang Zhao

Ultrasonic vibration-assisted cutting (UVAC) has been regarded as a promising technology to machine difficult-to-machine materials such as tungsten carbide, optical glass, and hardened steel in order to achieve superfinished surfaces. To increase vibration stability to achieve optical surface quality of a workpiece, a high-frequency ultrasonic vibration-assisted cutting system with a vibration frequency of about 104 kHz is used to machine spherical optical steel moulds. A series of experiments are conducted to investigate the effect of machining parameters on the surface roughness of the workpiece including nominal cutting speed, feed rate, tool nose radius, vibration amplitude, and cutting geometry. This research takes into account the effects of the constantly changing contact point on the tool edge with the workpiece induced by the cutting geometry when machining a spherical steel mould. The surface morphology and surface roughness at different regions on the machined mould, with slope degrees (SDs) of 0°, 5°, 10°, and 15°, were measured and analysed. The experimental results show that the arithmetic roughness Sa of the workpiece increases gradually with increasing slope degree. By using optimised cutting parameters, a constant surface roughness Sa of 3 nm to 4 nm at different slope degrees was achieved by the applied high-frequency UVAC technique. This study provides guidance for ultra-precision machining of steel moulds with great variation in slope degree in the pursuit of optical quality on the whole surface.


2011 ◽  
Vol 45 (3) ◽  
pp. 111-119 ◽  
Author(s):  
Magdy F. Iskander ◽  
Zhengqing Yun ◽  
Nuri Celik ◽  
Hyoungsun Youn ◽  
Nobutaka Omaki ◽  
...  

AbstractEmerging homeland security applications require low-cost and fast, deployable, high-frequency (HF) radar systems and the ability to operate in challenging terrain environments. With the need to cover as many border and coastal areas as possible, taking advantages of available transmitter resources to track targets using passive radar technologies is yet another area of research of considerable interest. In this paper, we describe the development of an HF radar system that meets these operational challenges, and we also highlight some recent implementation of the passive radar technology for homeland security applications. Specifically, we describe the design of a novel, electrically small HF antenna system consisting of three helical elements, one connected to the feed port while the other two are folded arms terminated with switchable loads. The antenna is 0.90-m (<3 feet) high with a small ground disk of 0.60 m (∼2 feet) diameter. The antenna is self-resonant at multiple frequencies (5.7, 16, 20.5, and 27.7 MHz) and with input impedance values that can be easily matched to a 50-Ω coaxial feed. Values of the electrical size ka range from 0.44 at 30 MHz down to 0.08 at 5.7 MHz. The achieved bandwidths range from 1.4% up to 12% and associated efficiencies range from 66.2% to 76% within the HF band (3‐30 MHz). As for the operational requirement in challenging terrain environments, a setup in a hilltop-type environment with a slope terrain and surface roughness was considered. A propagation modeling and ray-tracing approach was used to evaluate the impact of such terrain conditions on the effective interelement spacing of an HF radar antenna array and the subsequent impact on its beamforming and beam steering performance. It is shown that while the effect of the slope on the effective interelement spacing of the array could be very significant, diffraction effects from surface roughness resulted in a much smaller, but significant, error of about 18°. Results from some initial work on the implementation of passive radar technology, with focus on addressing the bandwidth requirement to ensure practical resolution values, are also described. It is shown that signals from wide-band transmitters (e.g., High Definition Television [HDTV] signals) rather than those from radio stations are required to provide acceptable range resolution. These as well as simulation and experimental results of the antenna design, and results from beamforming simulations illustrating the effect of a rough hilltop terrain on the HF radar performance are described.


2011 ◽  
Vol 130-134 ◽  
pp. 1310-1313
Author(s):  
Yu Fu Xu ◽  
Wen Dong Li ◽  
Xian Guo Hu ◽  
Qiong Jie Wang

The corrosion behavior during friction of refined bio-oil by distillation process was evaluated by high frequency reciprocating test rig. Both scanning electron microscopy (SEM) and energy dispersive spectrometer (EDS) were used to investigate the morphology and active elements contents on the rubbed surface on steel disk. The chemical structures of the oils and the topography and surface roughness of the wear scar were also studied by FTIR and surface roughness tester as well, respectively. The experimental results showed that corrosion behavior of bio-oil was improved after refining since the wear depth was 3.75µm and the worn surface roughness was 0.172µm, while they were 12.5µm and 0.217µm before refining. It was concluded that corrosion degree of worn surface was decreased after the bio-oil was refined, which was ascribed to the decrease of the acidic component content after the refining process.


2016 ◽  
Vol 2016 (1) ◽  
pp. 000358-000363 ◽  
Author(s):  
Qianfei Su ◽  
A. Ege Engin ◽  
Jerry Aguirre

Abstract Signal attenuation in transmission lines is a major issue for reliable transmission in high frequency range. Knowledge of the electrical parameters of printed circuit board (PCB), including dielectric constant and loss tangent, is critical. Moreover, surface roughness has a great effect on loss in high frequency. This paper demonstrates an effective simulation fitting method for electrical material characterization. Cavity resonator is chosen as the circuit for characterization. A methodology is presented to measure surface roughness from cross sections, and compared with values extracted from resonator measurements. Several materials and copper foils treatments, including low-profile, are analyzed in this paper.


Sign in / Sign up

Export Citation Format

Share Document