Fundamentals of Adhesion Failure for a Model Adhesive (PMMA/Glass) Joint in Humid Environments

2008 ◽  
Vol 84 (4) ◽  
pp. 339-367 ◽  
Author(s):  
K. T. Tan ◽  
C. C. White ◽  
D. L. Hunston ◽  
C. Clerici ◽  
K. L. Steffens ◽  
...  
Keyword(s):  
1924 ◽  
Vol 46 (2) ◽  
pp. 287-290 ◽  
Author(s):  
H. N. Ridyard
Keyword(s):  

Author(s):  
Rohit Verma ◽  
Lochan Sharma ◽  
Mayank Chauhan ◽  
Rahul Chhibber ◽  
Kanwer Singh Arora

The automobile industry has started using adhesive bonding to join load bearing components which aerospace industry has been using for decades. Adhesive lap joints are used frequently in the manufacture of automobile. In present study, structural adhesives were used to join the aluminium alloy (AA5083 H111) with the HSS dual phase (DP780) steel. Adhesive bonding appears to be one of the appropriate methods of joining dissimilar materials. The aim of this work is to analyze the tensile strength of similar and dissimilar joints. The influence of various parameters was also investigated such as the overlap length and the bondline thickness of specimens. In DP steel, there is 22% increase in strength for similar lap joint when overlap length changes from 10 mm to 15 mm, while there is 45% increase in strength when it varies from 15 mm to 20 mm. Similarly in case of Al alloy, there is 26% increased strength for similar lap joints when length varies from 10 mm to 15 mm, while it increased to 42% when length changes from 15 mm to 25 mm and there is about 35% increase in strength for length varies from 20 mm to 25 mm. In case of dissimilar joints, firstly there is about 16% increase in strength then there is 5% decrease while after that there is 45% increase in strength. Adhesion failure, cohesion failure and mixed failure were obtained experimentally during failure mode analysis. As the strength of joint increases, failure mode shows a transition from adhesion failure to cohesion failure. From the literature survey it is evident that limited work has been carried out on analysis of shear-tensile strength of adhesively bonded steel and aluminium joint with variation in bonding parameters. Not much work on failure mode analysis of bonded joints during tensile testing has been reported. In present work a noval attempt has been made to analyze the shear-tensile strength and failure mode of adhesively bonded steel and aluminium joint with variation in bonding parameters.


Buildings ◽  
2020 ◽  
Vol 10 (3) ◽  
pp. 59
Author(s):  
Barbara Francke ◽  
Artur Piekarczuk

This paper analyses the mechanism of the loss of functional properties of water-impermeable products used under ceramic tiles bonded with adhesives. Recorded damages were caused by selected ageing factors and were measured by the loss of adhesion of individual layers of the set. The analyzed phenomenon is found mainly on terraces and balconies located in a mid-European transitional climate, i.e., exposed to temperatures passing through 0 °C for three seasons a year. The tests reflected the action of three main functional factors, i.e., temperatures, water and freeze/thaw cycles. Tested waterproof coatings were grouped into three types, i.e., dispersion, cementitious and reaction resin-based products. Research kits consisted of liquid-applied water-impermeable products laid on a concrete substrate, adhesives and tiles. Comparing the effects of the action of the above-mentioned ageing factors revealed that water has the greatest impact on the reduction of the tensile adhesion strength of such sets. The adhesion of waterproof coatings to the concrete substrate showed higher values than the adhesion between the waterproof coating and the tile adhesive layers, regardless of the coating material. Both for samples not exposed to ageing factors, and for those exposed to such impacts, failure usually occurred in the adhesive layer or between the tile adhesive and the waterproof coating, without damaging the waterproof layer. The loss of adhesion of finishing layers to the substrate was not accompanied by a loss of tightness of the waterproof coating. The impact of negative water ageing was particularly destructive on the adhesion of cement-based tile adhesives to waterproof coatings made of polymer with a water dispersion of absorbability above 7% (V/V). There was no correlation among the results of adhesion of the finishing layers to the waterproofing layer after the action of the three ageing factors, i.e., water contact, elevated temperature and freeze/thaw cycles.


2019 ◽  
Vol 32 (7) ◽  
pp. 345-355 ◽  
Author(s):  
Chris Melvin ◽  
Eifion Jewell ◽  
Jakob Miedema ◽  
Koen Lammers ◽  
Arnoud Vooys ◽  
...  

Vacuum ◽  
1967 ◽  
Vol 17 (6) ◽  
pp. 363 ◽  
Keyword(s):  

Sign in / Sign up

Export Citation Format

Share Document