Analytical modelling of complex stiffness modulus tests in direct tension-compression on asphalt concrete and nonlinearity effect due to strain amplitude

2021 ◽  
pp. 1-31
Author(s):  
L. Coulon ◽  
G. Koval ◽  
C. Chazallon ◽  
J.-N. Roux
Keyword(s):  
Strain Amplitude ◽  
Asphalt Concrete ◽  
Analytical Modelling ◽  
Direct Tension ◽  
Stiffness Modulus ◽  
Nonlinearity Effect

Watertightness, cracking resistance, and self-healing of asphalt concrete used as a water barrier in dams

2013 ◽  
Vol 50 (3) ◽  
pp. 275-287 ◽  
Author(s):  
Yingbo Zhang ◽  
Kaare Höeg ◽  
Weibiao Wang ◽  
Yue Zhu
Keyword(s):  
Asphalt Concrete ◽  
Leakage Rate ◽  
Strain Rates ◽  
Self Healing ◽  
Test Results ◽  
Direct Tension ◽  
Coefficient Of Permeability ◽  
Tension Tests ◽  
Laboratory Test Results ◽  
Cracked Specimens

The coefficient of permeability of hydraulic asphalt concrete is in the range 10−8–10−10 cm/s. Laboratory test results show that triaxial specimens in axial compression can undergo axial strains up to 18% without any significant increase in permeability until approaching the compressive strength. For temperatures between 5 and 20 °C and strain rates between 2 × 10−3%/s and 5 × 10−3%/s, conventional hydraulic asphalt concrete can tolerate 1%–3% tensile strains before cracking in direct tension tests and strains up to 3%–4% in bending. At 20 °C the tensile and bending strains at cracking are 2–4 times higher than those at 0 °C, and at −20 °C they are approximately 0.2% and 0.8%, respectively. Asphalt concrete possesses pronounced crack self-healing properties. In the experiments, the crack leakage rate dropped 1–4 orders of magnitude within a few hours and the cracked specimens regained 55% of the intact tensile strength after only 1 day of self-healing. In summary, the comprehensive series of laboratory tests documents that asphalt concrete has characteristics that make the material extremely well suited for use in impervious barriers in dams, and the test results reported herein can be of great use in barrier design.

The Viscoelastic Characteristics of the Asphalt Concrete Modified with Different Synthetic Waxes Using a Modified Huet- Sayegh Model

2017 ◽  
Author(s):  
Grzegorz Mazurek
Keyword(s):  
Asphalt Concrete ◽  
Dynamic Modulus ◽  
Complex Modulus ◽  
Model Parameters ◽  
Fischer Tropsch ◽  
Stiffness Modulus ◽  
Molecular Weights ◽  
Cole Diagram ◽  
Sinusoidal Load ◽  
Viscoelastic Characteristics

The article presents the results of dynamic modulus tests carried on the asphalt concrete (AC16W). The sinusoidal load was applied to the samples in accordance with DTC-CY method. The neat bituminous binder (penetration grade 35/50) was modified by means two synthetic waxes, coming from the Fischer-Tropsch raction, with various molecular weights and softening point temperature results (hard and softer). The relaxation phenomenon in terms of changes in complex modulus and phase angle was evaluated using the modified Huet-Sayegh (2S2P1D). Estimated model parameters pointed out that the addition of the synthetic wax with the high (hard wax) and the low (softer wax) molecular weight raised the stiffness of the bituminous binder in relation to the reference bitumen 35/50. The application of the modified Huet-Sayegh model showed that the presence of the synthetic wax in the bitumen significantly affected the stiffness modulus of considered asphalt concretes. Basing analysis on Cole-Cole diagram it was found significant differences in the viscoelastic behaviour between the reference asphalt concrete and the asphalt concretes with synthetic waxes. In contrast, there were no significant differences between viscoelastic properties of tested asphalt concretes modified, used in the experiment, synthetic waxes. Furthermore, the sensitivity to the loading time of asphalt concretes containing both synthetic waxes was marginal.

The Influence of Hydrated Lime, Portland Cement and Cement Dust on Rheological Properties of Recycled Cold Mixes with Foamed Bitumen

2017 ◽  
Author(s):  
Przemysław Buczynski ◽  
Marek Iwanski
Keyword(s):  
Portland Cement ◽  
Rheological Properties ◽  
Complex Modulus ◽  
Hydrated Lime ◽  
Laboratory Evaluation ◽  
Cement Kiln ◽  
Direct Tension ◽  
Stiffness Modulus ◽  
Hydraulic Binder ◽  
Foamed Bitumen

This article presents a laboratory evaluation of the viscoelastic properties of recycled base courses produced with different fillers. The aim of this study was to investigate the influence of loading time and temperature on the complex modulus (E*) and the phase angle (6) of recycled base courses with respect to selected additives used. The mixtures contained reclaimed asphalt pavement RAP, crushed stone from existing base courses and virgin aggregate. Foamed bitumen 50/70 at 2.5% was used as a binder. The hydraulic binder constituted 3.0% of the recycled base course mixture. Portland cement, hydrated lime and cement kiln dust CKD were added as fillers. Evaluation of rheological properties of recycled base courses according to selected additives was carried out to the procedure set out in EN 12697-26 annex D. The evaluation of stiffness modulus was conducted in the direct tension- compression test on cylindrical samples (DTC-CY). The samples were subjected to the cycles of sinusoidal strain with an amplitude Bo < 25μB. All tests were performed over a range of temperatures (5 ºC, 13 ºC, 25 ºC, 40 ºC) and loading times (0.1 Hz, 0.3 Hz, 1 Hz, 3 Hz, 10 Hz, 20 Hz). The results were used to model stiffness modulus master curves of the recycled base courses containing selected additives in the hydraulic binder.

scholarly journals Effect of Hydrated Lime on Indirect Tensile Stiffness Modulus of Asphalt Concrete Produced in Half-Warm Mix Technology

Materials ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 4731
Author(s):  
Mateusz M. Iwański
Keyword(s):  
Asphalt Concrete ◽  
Permanent Deformation ◽  
Active Agent ◽  
Hydrated Lime ◽  
Partial Replacement ◽  
Stiffness Modulus ◽  
Limestone Filler ◽  
Tensile Stiffness ◽  
Lime Content ◽  
Indirect Tensile

Half-warm mix asphalt (HWMA) mixtures can be produced at temperatures ranging from 100 °C to 130 °C, depending on the production methods used. The lowest mixing temperature can be achieved by using water-foamed bitumen. The mixture should be characterized by a long service life, defined by the resistance to permanent deformation and high stiffness modulus at temperatures above zero. It is therefore important to ensure the adequately high quality of the bitumen binder. Bitumen 50/70 was provided with appropriate quality foaming characteristics (expansion ratio, ER, half-life, t1/2) by adding a surface-active agent (SAA) at 0.6 wt % before foaming. Then asphalt concrete (AC) 8 S was designed and produced with the recommended water-foamed binder. Hydrated lime, an additive substantially affecting asphalt concrete mechanical parameters, was used at 0, 15, 30, and 45 wt % as a partial replacement for the limestone filler. The influence of the amount of hydrated lime on the content of voids, indirect tensile stiffness modulus at −10 °C, 0 °C, +10 °C, +20 °C, and +30 °C, and the resistance to permanent deformation was investigated. Statistical analysis of the test results showed the quantity of 30% to be the optimum hydrated lime content. The AC 8 S resistance to permanent deformation was determined at the optimum hydrated lime content. The comprehensive evaluation revealed a synergistic effect between bitumen 50/70, modified before foaming with 0.6 wt % SAA and 30 wt % hydrated lime as the limestone filler replacement, and the half warm mixture AC 8 S, in terms of the standard requirements and durability of the HWMA concrete in pavement applications.

Influences of Aging History on Low Temperature Performance of Asphalt Concrete

2008 ◽  
Vol 385-387 ◽  
pp. 493-496 ◽  
Author(s):  
Shao Peng Wu ◽  
Guo Jun Zhu ◽  
Ling Pang ◽  
Cong Hui Liu
Keyword(s):  
Low Temperature ◽  
Flexural Strength ◽  
Asphalt Concrete ◽  
Tensile Strain ◽  
Natural Aging ◽  
Bending Stiffness ◽  
Bending Test ◽  
Stiffness Modulus ◽  
Stone Mastic Asphalt ◽  
High And Low Temperatures

According to three-point bending test, this paper explores the influence of low temperature on the flexural strength, the tensile strain and bending stiffness modulus of the aged Stone Mastic Asphalt (SMA-13) concrete. The asphalt mixtures are aged according to the short-term aging (at 135°C, 4 hours), and long-term aging (asphalt concrete at 85°C, 120 hours) and natural aging (3 months, 6 months and 9 months). The result shows that, with the same loading rate, the tensile strain of specimens at -30°C are smaller than those at -10°C; but when temperature is certain, the tensile strain of specimens lager than those of aged specimens. The longer the aging time lasts, the more flexural strength differences between high and low temperatures can be found. A pretty well index variation can be found between the tensile strain and temperature. The same trend also appears between the bending stiffness modulus and temperature of SMA-13 asphalt concrete.

scholarly journals Potential of Using Imidazoline in Recycled Asphalt Pavement

2019 ◽  
Vol 14 (4) ◽  
pp. 521-542
Author(s):  
Robert Jurczak ◽  
Paweł Mieczkowski ◽  
Bartosz Budziński
Keyword(s):  
Asphalt Concrete ◽  
Asphalt Pavement ◽  
Asphalt Mixtures ◽  
Fatigue Performance ◽  
Recycled Asphalt Pavement ◽  
Recycled Asphalt ◽  
Stiffness Modulus ◽  
Optimum Content ◽  
Environmental Considerations ◽  
Freezing Temperatures

The environmental considerations need to be taken into account in any road resurfacing and upgrading project, for example, by reusing asphalt rubble for production of new pavement courses. Mixtures containing larger amounts of recycled asphalt pavement are improved by adding rejuvenator additives. The tests performed on the recycled asphalt mixtures containing lard imidazoline confirm the suitability of this agent for paving applications. Lard imidazoline was found to improve the stiffness modulus, fatigue performance and resistance to the action of water and freezing temperatures. The parameters obtained at the optimum content of additive complied with the criteria defined for virgin asphalt concrete and other mixtures of that kind.

Sign in / Sign up

Export Citation Format

Share Document