Comprehensive study on physical properties of CdTe thin films: Effect of post-deposition high annealing temperature

Author(s):  
Ebrahim Hasani ◽  
Davood Raoufi
2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Dung Van Hoang ◽  
Anh Tuan Thanh Pham ◽  
Truong Huu Nguyen ◽  
Thang Bach Phan ◽  
Vinh Cao Tran

In this work, undoped, aluminum-, and gallium-doped ZnO thin films (ZnO-H, AZO-H, and GZO-H, respectively) deposited on soda-lime glass substrates by magnetron sputtering method in a gas mixture of hydrogen and argon are annealed at various temperatures in the range of 200–500°C in air to evaluate the durability of those films under annealing temperature. From photoluminescence spectra, formation of point defects, especially oxygen vacancies, when hydrogen diffuses out of the films at high annealing temperature is exhibited via a significant increase of visible emissions. We find out that carrier concentration and Hall mobility of AZO-H and ZnO-H films dramatically decrease, while those of GZO-H film are still stable as the annealing temperature increased from 200°C to 300°C. We proposed a model for interpreting the thermal durability of GZO-H film that, at an annealing temperature of 300°C, Ga3+ ions located at adjacent Zn sites can push hydrogen atoms, which are broken out of the antibonding sites which are perpendicular to the c -axis (AB┴), into bond center sites paralleled to the c -axis (BC//). The movement of hydrogen from AB┴ to BC// site also gives rise to the durability of electrical properties of GZO-H films at the high annealing temperature.


2013 ◽  
Vol 832 ◽  
pp. 695-699 ◽  
Author(s):  
M. Sobri ◽  
A. Shuhaimi ◽  
K.M. Hakim ◽  
M.H. Mamat ◽  
S. Najwa ◽  
...  

Nickel (Ni) / indium tin oxide (ITO) nanostructures were deposited on glass and silicon (111) substrates by RF magnetron sputtering using a nickel target and ITO (In-Sn, 90%-10%) targets. The post-deposition annealing has been performed for Ni/ITO films in air and the effect of annealing temperature on the electrical, optical and structural properties on ITO films was studied. We found the appearance of (411) and (622) peaks in addition to (400) and (222) major peaks, which indicates an improvement of the film crystallinity at high annealing temperature of 650°C. The samples show higher transmittance of more than 90% at 460 nm after annealing. In addition, increasing the annealing temperatures also improve the film electrical properties. The resistivity decreases to 6.67×10-6Ωcm when annealed at 500°C as opposed to 6.75×10-5Ωcm in as-deposited film.


2018 ◽  
Vol 123 ◽  
pp. 216-222 ◽  
Author(s):  
S.L. Patel ◽  
S. Chander ◽  
A. Purohit ◽  
M.D. Kannan ◽  
M.S. Dhaka

2021 ◽  
Vol 1016 ◽  
pp. 1636-1641
Author(s):  
Xiao Dong Wu ◽  
Xiao Li Liu ◽  
Ling Fei Cao ◽  
Guang Jie Huang

The aim of this work was to analyze the recrystallization behavior of cold rolled Aluminum/graphene composites during annealing. The Aluminum/graphene composite was cold rolled firstly, and then annealed at different temperature (250°C, 300°C, 350°C, 400°C) and for various time (1 h, 2 h, 8 h, 32 h). Full recrystallization did not occur until the annealing temperature was above 300 °C. With annealing temperature increasing from 250 to 300°C, the hardness of the composites decreased from 49.6 to 27.6 HV. Grain growth were not observed at high annealing temperature and longer annealing time, which suggested that Graphene has strong pinning effect on the grain boundary of Aluminum.


Sign in / Sign up

Export Citation Format

Share Document