Low contact resistivity between Ni/Au and p-GaN through thin heavily Mg-doped p-GaN and p-InGaN compound contact layer

2015 ◽  
Vol 24 (11) ◽  
pp. 116803 ◽  
Author(s):  
Xiao-Jing Li ◽  
De-Gang Zhao ◽  
De-Sheng Jiang ◽  
Ping Chen ◽  
Jian-Jun Zhu ◽  
...  
1995 ◽  
Vol 402 ◽  
Author(s):  
S. Oktyabrsky ◽  
M. O. Aboelfotoh ◽  
J. Narayan

AbstractChemistry, crystal structure, interfacial microstructure and electrical characteristics of novel Cu-Ge alloyed ohmic contacts to n-type GaAs with a very low specific contact resistivity ((4–6)×10−7 Ω·cm2 for n∼1×1017 cm−3) were investigated by various methods. The Cu-Ge alloys with a wide range of Ge concentration, from 15 to 40 at %, were prepared by depositing sequentially Cu and Ge layers (or vise versa) onto GaAs substrates at room temperature followed by annealing at 400°C. It is shown that Cu reacts only with Ge to form the ξ and ε1-Cu3Ge phases. The latter has an orthorhombic structure with average lattice parameters: a = 5.301 Å, bo = 4.204 Å, co = 4.555 Å, arising from the parent hexagonal ξ-phase by Cu-Ge ordering along ao. The interface with GaAs is atomically sharp and free from secondary phases. The ε1-Cu3Ge ordered phase which is chemically inert with respect to GaAs, is believed to be responsible for high thermal stability (up to 450°C), interface sharpness, high contact layer uniformity and low specific resistivity of 6 μΩ cm. Formation of the Cu-Ge phases creates a highly doped n+-GaAs surface layer which leads to the low contact resistivity.


2002 ◽  
Vol 743 ◽  
Author(s):  
Brett A. Hull ◽  
Suzanne E. Mohney ◽  
Uttiya Chowdhury ◽  
Russell D. Dupuis ◽  
David Gotthold ◽  
...  

ABSTRACTGold, palladium, platinum or nickel ohmic contacts on Mg doped p-type AlxGa1-xN with x = 0.4 and x = 0.45 have been examined. The Au contact provided the lowest contact resistivity with pc = 1.8 (± 1.1) x 10−3 Ωcm2, but only following annealing at 850°C. For the Pd, Au, and Pt contacts annealed at greater than 700°C, a rapid degradation in the current-voltage curves was observed upon testing. The degradation was induced by exposure to sub-bandgap light and was reversed with a mild anneal at 500°C. Possible mechanisms for the degradation are discussed.


2017 ◽  
Vol 56 (14) ◽  
pp. 4197 ◽  
Author(s):  
Feng Liang ◽  
Degang Zhao ◽  
Desheng Jiang ◽  
Zongshun Liu ◽  
Jianjun Zhu ◽  
...  

Author(s):  
А.В. Малевская ◽  
В.П. Хвостиков ◽  
Ф.Ю. Солдатенков ◽  
О.А. Хвостикова ◽  
А.С. Власов ◽  
...  

AbstractOhmic contacts of power AlGaAs/GaAs-based photovoltaic converters were studied, and a technique for their fabrication was developed. Effect of the doping level of the contact layer on the free-carrier density and the contact resistivity was examined. A technique for fabrication of 2- to 4-μm-thick ohmic contacts with electrochemical deposition of gold layers was studied. The effect of deposition modes on the surface morphology of ohmic contacts and their solidity and conductivity was revealed.


2004 ◽  
Vol 831 ◽  
Author(s):  
R. Kröger ◽  
J. Dennemarck ◽  
T. Böttcher ◽  
S. Figge ◽  
D. Hommel

ABSTRACTThe effect of a highly Mg doped subcontact layer on top of GaN grown by metal organic vapor phase epitaxy and its interface to a Pd/Au contact layer was investigated by means of transmission electron microscopy and electrical characterization techniques. Use was made of prior investigations of the Mg doping characteristics, which showed the existence of a segregation related defect free layer even for doping levels as high as 5×10−19cm−3, which thickness depends on the Mg to Ga molar precursor flow ratio. For a given subcontact layer thickness of 15 nm a critical precursor molar flow ratio of 0.035 resulted in a smooth surface showing an interfacial layer indicating a Pd/Ga alloying. This layer resulted in a contact resistivity as low as 2×10−5 Ωcm2. For a flow ratio of 0.070 the surface was found to be rough due to defect formation resulting in a contact resistivity as high as 10−3 Ωcm2 similar to the value obtained without subcontact layer. Moreover, the metallization layer showed in all cases a texture of the {111} lattice planes with respect to the {0002} planes of the GaN.


2015 ◽  
Vol 24 (9) ◽  
pp. 096804 ◽  
Author(s):  
Xiao-Jing Li ◽  
De-Gang Zhao ◽  
De-Sheng Jiang ◽  
Ping Chen ◽  
Jian-Jun Zhu ◽  
...  

2012 ◽  
Vol 620 ◽  
pp. 453-457
Author(s):  
E. Azimah ◽  
Norzaini Zainal ◽  
Hassan Zainuriah ◽  
Ahmad Shuhaimi ◽  
Azlan Bahrin

Apossible evidence of Mg related emission in Mg doped GaN material is observed inoptical measurement, even without thermal annealing. Meanwhile, the electrical properties of the sample improve when Ni/Au contact layer was annealed up to 400°C, but degrade at further temperature. We propose that such behavior isrelated to degradation of surface morphology of metal contact at higher temperature.


1993 ◽  
Vol 318 ◽  
Author(s):  
P. Ressel ◽  
H. Strusny ◽  
D. Fritzsche ◽  
H. Kräutle ◽  
K. Mause

ABSTRACTThe development of shallow ohmic contacts for the thin p-InGaAs layer (p≤1*1019 cm−5) of InP-based heterojunction bipolar transistors is a severe challenge to contact technology. While standard metallizations reveal several drawbacks, Pd/Ge-based systems emerged as promising candidates. In this work, Zn or Cd was implanted into the inner Pd contact layer for lowering contact resistivity. We present a study of the electrical and metallurgical properties of Pd/Ge contacts to p-InGaAs, and the influence of Zn and Cd implanted into the metallization. The resistivity of implanted and annealed (450-575 °C) contacts is reduced up to one order of magnitude compared to the unimplanted contact. Backside SIMS measurements show that annealing leads to a very limited interdiffusion at the interface. Cd and Zn diffuse into the InGaAs layer to a depth of approx. 30 and 40 nm, respectively. Due to these features, this implanted Pd/Ge contact scheme is a promising candidate for shallow contacts to p-InGaAs.


Sign in / Sign up

Export Citation Format

Share Document