scholarly journals Concentrated Solar Power (CSP) for Sustainable Architecture to Supply Domestic Hot Water and Heating Loads of Buildings

2021 ◽  
Vol 2042 (1) ◽  
pp. 012110
Author(s):  
Hamidreza Zarrinkafsh ◽  
Nasim Eslamirad ◽  
Francesco De Luca
Keyword(s):  
Energy Production ◽  
Tracking System ◽  
Hot Water ◽  
Production Operation ◽  
Concentrated Solar Power ◽  
Parabolic Trough ◽  
Solar Concentrators ◽  
Sustainable Architecture ◽  
Urban Contexts ◽  
Heating Loads

Abstract Parabolic Trough Concentrators (PTC) are the most common solar concentrators. However, the high cost of production, operation, sun- tracking system, and the environmental sensitivity made them unprofitable for urban contexts. Lenses are more efficient and effective, but the complexity of manufacturing made them less used in sustainable architecture. This research proposes a liquid lens to be integrated into buildings’ envelope and compared with a PTC based on the energy production and reduced CO2 emissions over a year. The output energy, temperature, and efficiency of concentrator are obtained by the physics of light equations, and Ray-tracing software simulation. The results show that water lenses are at least 6% more efficient, their output temperature is higher, their underneath greenhouse effect made them less sensitive to the environment, and are still productive in high latitudes where PTCs are not operative. The paper presents the full result of the research that was registered as a patent.

Design of a Solar Tunnel Dryer Combined Heat with a Parabolic Trough for Paddy Drying

2016 ◽  
Vol 851 ◽  
pp. 239-243 ◽  
Author(s):  
Krissadang Sookramoon
Keyword(s):  
Heat Exchanger ◽  
Performance Test ◽  
Focal Point ◽  
Tracking System ◽  
Cross Flow ◽  
Hot Water ◽  
Parabolic Trough ◽  
Tunnel Dryer ◽  
And Performance ◽  
Flat Plate Collector

This paper presents the design, build and performance test of a solar tunnel dryer combined heat with a parabolic trough for paddy drying. A 2.27 m² parabolic trough stainless steel made with a single-axis solar tracking system produced hot water and delivered to the cross flow heat exchanger equipped with a solar tunnel dryer with the size of flat plate collector of 2.112 m2. The system received solar radiation and reflected sunlight to the receiver at the focal point of a parabolic trough. At this point, a copper heat pipe with the inside diameter of 25.4 mm for water heating is placed. A parabolic trough is covered with plastic sheets for protecting the wind in order to prevent the heat loss by convection. The produced hot water is used to warm the air and is sent to the heat exchanger and the blower passes hot air through the drying chamber of solar tunnel to dry paddy. The average drying temperature was 57.73 °C. The paddy moisture content was assessed in a reduction from 49.96 to 15.61 MC (% d.b.) in 6 hours. The heated air was around 245.87 W, with the incoming heat in the solar tunnel dryer of 1271.84 W. The thermal efficiency of a solar tunnel dryer, a parabolic trough, and the overall efficiency were on the average of 28.31%, 8.73%, and 3.80%, respectively.

Approach to Designing a Solar Concentrator for Small Scale Remote Power Application

2010 ◽  
Author(s):  
Khaled Metwally ◽  
Lamyaa A. El-Gabry ◽  
Ahmed Makhlouf
Keyword(s):  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Hot Water ◽  
Heat Transfer Fluid ◽  
Working Fluid ◽  
Small Scale ◽  
Concentrated Solar Power ◽  
Parabolic Trough ◽  
Capstone Project ◽  
Power Application

A small-scale concentrated solar power unit was designed to provide electricity and hot water using an organic Rankine cycle for Egypt as part of an undergraduate capstone project. The system was designed for a target power output of 3 KW. It uses parabolic troughs to heat ethylene glycol used as the heat transfer fluid which absorbs heat in the trough collector and transfers it to the working fluid through a heat exchanger. The system consists of 9 parabolic troughs and a total aperture area of 67 square meters, providing the required 3 KW of energy to the ORC. One parabolic trough was manufactured to test its thermal efficiency according to ASHRAE standard 93-2003 and compare it to its calculated value. A simple microcontroller-based system was used to track the sun.

scholarly journals Performance Improvement of the Parabolic Trough Solar Collector Using Different Types of Fluids with Numerical Simulation

2018 ◽  
Vol 26 (6) ◽  
pp. 332-347
Author(s):  
Saad T. Hamidi ◽  
Fikrat A.K. Fattah ◽  
Mohammed S. Ghanam
Keyword(s):  
Solar Collector ◽  
Tracking System ◽  
Experimental Tests ◽  
Working Fluid ◽  
Distilled Water ◽  
Parabolic Trough ◽  
Solar Concentrators ◽  
Engineering Department ◽  
Useful Heat ◽  
Parabolic Trough Solar Collector

Solar concentrators are an important facility to utilize the solar energy. There are many kinds of solar concentrators. In this work  an experimental has been implemented to improve the thermal performance of Parabolic Trough Solar Collector (PTSC) using three different fluids as a working fluid (water, nanoparticles of  CuO  mixed with distilled water nanoparticles of   mixed with  distilled water) with concentration ratio 0.01% and mass flow rate 20Lt/hr without tracking system. The experimental tests have been carried out in electro-mechanical engineering department at university of technology in Baghdad city during October 2017 and daytime between (9am -15pm) hours. The obtained results for three different fluids are as follows:  - Using (CuO + distilled water) as a working fluid increases the average of the output temperatures by 10.4%,  the average of useful heat gains   increases  by 11%  and the average of the collector efficiencies increases by15%.    - Using ( +distilled water) as a working fluid increased the average of output temperatures by 4%, the average of useful heat gains is increased by 6.5% and the average of collector efficiencies is increased by 8.2%.  

Design of Parabolic Trough Solar Collector (PTC) and Numerical Simulation for Improving the Efficiency

2013 ◽  
Vol 291-294 ◽  
pp. 53-60
Author(s):  
A.A.M. Hassanein ◽  
Ling Qiu
Keyword(s):  
Solar Cells ◽  
Focal Point ◽  
Tracking System ◽  
Control Unit ◽  
Hot Water ◽  
Parabolic Trough ◽  
Lower Efficiency ◽  
Solar Altitude ◽  
Tracking Motion ◽  
Parabolic Trough Solar Collector

This research focus on two PTC designs, one in Runzhen-school, China (latitude 36.5°N, longitude110°E and 386m altitude) and the second PTC with tracking system. The study showed that, using one tube concentrate in the focal point with fixed PTC gives lower efficiency compared with using two vacuum tubes, as the variation of solar altitude angle is large. So using two focal points results a better heating. The new system uses PTC with sun tracking system to maximize solar radiation absorptions, that leading to increase the hot water temperature and has higher system efficiency. In addition, this system supplies two batteries by electricity coming from two solar-cells and it’s produced for the tracking system working during hours of sunlight. The photovoltaic electricity provided is stored in batteries and then used for tracking motion. The tracing motion receives orders from a control unit, which works at different voltage in two solar cells.

scholarly journals Life Cycle Assessment of the Use of Phase Change Material in an Evacuated Solar Tube Collector

Energies ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 4146
Author(s):  
Agnieszka Jachura ◽  
Robert Sekret
Keyword(s):  
Life Cycle Assessment ◽  
Life Cycle ◽  
Environmental Impact ◽  
Phase Change ◽  
Phase Change Material ◽  
Solar Collector ◽  
Hot Water ◽  
Production Operation ◽  
Management Scenarios ◽  
Change Material

This paper presents an environmental impact assessment of the entire cycle of existence of the tube-vacuum solar collector prototype. The innovativeness of the solution involved using a phase change material as a heat-storing material, which was placed inside the collector’s tubes-vacuum. The PCM used in this study was paraffin. The system boundaries contained three phases: production, operation (use phase), and disposal. An ecological life cycle assessment was carried out using the SimaPro software. To compare the environmental impact of heat storage, the amount of heat generated for 15 years, starting from the beginning of a solar installation for preparing domestic hot water for a single-family residential building, was considered the functional unit. Assuming comparable production methods for individual elements of the ETC and waste management scenarios, the reduction in harmful effects on the environment by introducing a PCM that stores heat inside the ETC ranges from 17 to 24%. The performed analyses have also shown that the method itself of manufacturing the materials used for the construction of the solar collector and the choice of the scenario of the disposal of waste during decommissioning the solar collector all play an important role in its environmental assessment. With an increase in the application of the advanced technologies of materials manufacturing and an increase in the amount of waste subjected to recycling, the degree of the solar collector’s environmental impact decreased by 82% compared to its standard manufacture and disposal.

scholarly journals Optimal design of the solar tracking system of parabolic trough concentrating collectors

2020 ◽  
Vol 15 (4) ◽  
pp. 613-619
Author(s):  
Li Kong ◽  
Yunpeng Zhang ◽  
Zhijian Lin ◽  
Zhongzhu Qiu ◽  
Chunying Li ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Solar Radiation ◽  
Tracking System ◽  
Low Cost ◽  
Parabolic Trough ◽  
The North ◽  
Tracking Mode ◽  
Solar Tracking ◽  
East West

Abstract The present work aimed to select the optimum solar tracking mode for parabolic trough concentrating collectors using numerical simulation. The current work involved: (1) the calculation of daily solar radiation on the Earth’s surface, (2) the comparison of annual direct solar radiation received under different tracking modes and (3) the determination of optimum tilt angle for the north-south tilt tracking mode. It was found that the order of solar radiation received in Shanghai under the available tracking modes was: dual-axis tracking > north-south Earth’s axis tracking > north-south tilt tracking (β = 15°) > north-south tilt tracking (β = 45) > north-south horizontal tracking > east-west horizontal tracking. Single-axis solar tracking modes feature simple structures and low cost. This study also found that the solar radiation received under the north-south tilt tracking mode was higher than that of the north-south Earth’s axis tracking mode in 7 out of 12 months. Therefore, the north-south tilt tracking mode was studied separately to determine the corresponding optimum tilt angles in Haikou, Lhasa, Shanghai, Beijing and Hohhot, respectively, which were shown as follows: 18.81°, 27.29°, 28.67°, 36.21° and 37.97°.

Microcontroller Based Single Axis Intelligent Control Sun Tracker for Parabolic Trough Collectors

2012 ◽  
Vol 562-564 ◽  
pp. 1772-1775
Author(s):  
Shakeel Akram ◽  
Farhan Hameed Malik ◽  
Rui Jin Liao ◽  
Bin Liu ◽  
Tariq Nazir
Keyword(s):  
Energy Efficiency ◽  
Embedded System ◽  
Alternative Energy ◽  
Power Plants ◽  
Tracking System ◽  
Appropriate Technology ◽  
Working Fluid ◽  
The Sun ◽  
Solar Collectors ◽  
Parabolic Trough

Due to the complex design and high costs of production, solar thermal systems have fallen behind in the world of alternative energy systems. Different mechanisms are applied to increase the efficiency of the solar collectors and to reduce the cost. Solar tracking system is the most appropriate technology to increase the efficiency of solar collectors as well as solar power plants by tracking the sun timely. In order to maximize the efficiency of collectors, one needs to keep the reflecting surface of parabolic trough collectors perpendicular to the sun rays. For this purpose microcontroller based real time sun tracker is designed which is controlled by an intelligent algorithm using shadow technique. The aim of the research project is to test the solar-to-thermal energy efficiency by tracking parabolic trough collector (PTC). The energy efficiency is determined by measuring the temperature rise of working fluid as it flows through the receiver of the collector when it is properly focused. The design tracker is also simulated to check its accuracy. The main purpose to design this embedded system is to increase the efficiency and reliability of solar plants by reducing size, complexity and cost of product.

Sign in / Sign up

Export Citation Format

Share Document