scholarly journals Applicability of DIN 5036-3 to Transmittance Haze Measurement

2022 ◽  
Vol 2149 (1) ◽  
pp. 012011
Author(s):  
Wen-Chun Liu ◽  
Hsueh-Ling Yu
Keyword(s):  
Incident Beam ◽  
Integrating Sphere ◽  
Total Transmittance ◽  
Theory And Experiment

Abstract This paper evaluates the applicability of the method described in DIN 5036-3 for transmittance haze measurement, theoretically and experimentally. It is shown that DIN 5036-3 is valid for total transmittance measurement. However, when applying to diffuse transmittance measurement, the measured value is lower than the theoretical one, resulting a lower value of calculated transmittance haze. The reflectance of the integrating sphere and collimation of the incident beam are the keys to achieve better agreement between theory and experiment. Further study is necessary to recommend solutions for the discovered issues.

scholarly journals Optical Scattering Properties of Intralipid Phantom in Presence of Encapsulated Microbubbles

2014 ◽  
Vol 2014 ◽  
pp. 1-9 ◽  
Author(s):  
Homa Assadi ◽  
Raffi Karshafian ◽  
Alexandre Douplik
Keyword(s):  
Contrast Agents ◽  
Volume Concentration ◽  
Optical Scattering ◽  
Imaging Systems ◽  
Integrating Sphere ◽  
Optical Contrast ◽  
Optical Contrast Agents ◽  
Diagnostic Modalities ◽  
Total Transmittance ◽  
Potential Use

In imaging, contrast agents are utilized to enhance sensitivity and specificity of diagnostic modalities. In ultrasound imaging, microbubbles (MBs)—a gas-core shell-encapsulated agent—are used clinically as contrast agents. The working hypothesis of this study is that microbubbles can be employed as an intravascular contrast agent in optical imaging systems. In this work, the interaction of light and microbubbles in a turbid medium (intralipid) was investigated, particularly, the effect of MBs on the reduced scattering and absorption coefficients. Diffuse reflectance (DR) and total transmittance (TT) measurements of highly scattering intralipid suspension (0.5–5%) were measured using spectroscopic integrating sphere system in the absence and presence of Definity microbubbles. The optical properties were computed using the inverse adding doubling (IAD) software. The presence of microbubbles increased DR and decreased TT of intralipid phantoms. In the presence of MBs (0.5% volume concentration), the reflectance of the intralipid phantom increased from 35% to 100%. The reduced scattering coefficient increased significantly (30%) indicating potential use of MBs as optical contrast agents in light based modalities.

scholarly journals Alternative Measurement Configurations for Extracting Bulk Optical Properties Using an Integrating Sphere Setup

2016 ◽  
Vol 71 (2) ◽  
pp. 224-237 ◽  
Author(s):  
Suresh N. Thennadil ◽  
Yi-chieh Chen
Keyword(s):  
Optical Properties ◽  
Near Infrared ◽  
Scattered Light ◽  
Integrating Sphere ◽  
Reflectance Measurement ◽  
Bulk Absorption ◽  
Bulk Scattering ◽  
Doubling Method ◽  
Reflectance Measurements ◽  
Total Transmittance

The usual approach for estimating bulk optical properties using an integrating sphere measurement setup is by acquiring spectra from three measurement modes namely collimated transmittance (Tc), total transmittance (Td), and total diffuse reflectance (Rd), followed by the inversion of these measurements using the adding–doubling method. At high scattering levels, accurate acquisition of Tc becomes problematic due to the presence of significant amounts of forward-scattered light in this measurement which is supposed to contain only unscattered light. In this paper, we propose and investigate the effectiveness of using alternative sets of integrating sphere measurements that avoid the use of Tc and could potentially increase the upper limit of concentrations of suspensions at which bulk optical property measurements can be obtained in the visible–near-infrared (Vis-NIR) region of the spectrum. We examine the possibility of replacing Tc with one or more reflectance measurements at different sample thicknesses. We also examine the possibility of replacing both the collimated (Tc) and total transmittance (Td) measurements with reflectance measurements taken from different sample thicknesses. The analysis presented here indicates that replacing Tc with a reflectance measurement can reduce the errors in the bulk scattering properties when scattering levels are high. When only multiple reflectance measurements are used, good estimates of the bulk optical properties can be obtained when the absorption levels are low. In addition, we examine whether there is any advantage in using three measurements instead of two to obtain the reduced bulk scattering coefficient and the bulk absorption coefficient. This investigation is made in the context of chemical and biological suspensions which have a much larger range of optical properties compared to those encountered with tissue.

Instrumentation for detecting channelling radiation in the high-voltage electron microscope

1983 ◽  
Vol 41 ◽  
pp. 318-319
Author(s):  
J. H. Butler ◽  
C. J. Humphreys
Keyword(s):  
Monochromatic Light ◽  
Incident Beam ◽  
Laboratory Frame ◽  
Relativistic Electrons ◽  
Voltage Electron ◽  
Dipole Emission ◽  
Sinusoidal Oscillations ◽  
Pass Through ◽  
Incident Beam Energy ◽  
Increasing Function

Electromagnetic radiation is emitted when fast (relativistic) electrons pass through crystal targets which are oriented in a preferential (channelling) direction with respect to the incident beam. In the classical sense, the electrons perform sinusoidal oscillations as they propagate through the crystal (as illustrated in Fig. 1 for the case of planar channelling). When viewed in the electron rest frame, this motion, a result of successive Bragg reflections, gives rise to familiar dipole emission. In the laboratory frame, the radiation is seen to be of a higher energy (because of the Doppler shift) and is also compressed into a narrower cone of emission (due to the relativistic “searchlight” effect). The energy and yield of this monochromatic light is a continuously increasing function of the incident beam energy and, for beam energies of 1 MeV and higher, it occurs in the x-ray and γ-ray regions of the spectrum. Consequently, much interest has been expressed in regard to the use of this phenomenon as the basis for fabricating a coherent, tunable radiation source.

Arsenic segregation in polysilicon

1983 ◽  
Vol 41 ◽  
pp. 154-155 ◽  
Author(s):  
P.E. Batson ◽  
C.R.M. Grovenor ◽  
D.A. Smith ◽  
C. Wong
Keyword(s):  
Incident Beam ◽  
Silicon Wafers ◽  
Chemical Polishing ◽  
Bright Field Image ◽  
Beam Size ◽  
Stem Analysis ◽  
Bright Field ◽  
Twin Boundaries ◽  
X Ray ◽  
Line Scan

In this work As doped polysilicon was deposited onto (100) silicon wafers by APCVD at 660°C from a silane-arsine mixture, followed by a ten minute anneal at 1000°C, and in one case a further ten minute anneal at 700°C. Specimens for TEM and STEM analysis were prepared by chemical polishing. The microstructure, which is unchanged by the final 700°C anneal,is shown in Figure 1. It consists of numerous randomly oriented grains many of which contain twins.X-ray analysis was carried out in a VG HB5 STEM. As K α x-ray counts were collected from STEM scans across grain and twin boundaries, Figures 2-4. The incident beam size was about 1.5nm in diameter, and each of the 20 channels in the plots was sampled from a 1.6nm length of the approximately 30nm line scan across the boundary. The bright field image profile along the scanned line was monitored during the analysis to allow correlation between the image and the x-ray signal.

Resolution Attainable With the Present Day STEM

1973 ◽  
Vol 31 ◽  
pp. 230-231 ◽  
Author(s):  
J. S. Wall ◽  
J. P. Langmore ◽  
H. Isaacson ◽  
A. V. Crewe
Keyword(s):  
Spherical Aberration ◽  
Focal Length ◽  
Incident Beam ◽  
Scanning Transmission Electron Microscope ◽  
Aperture Size ◽  
Magnetic Lens ◽  
Peak Intensity ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
Half Angle

The scanning transmission electron microscope (STEM) constructed by the authors employs a field emission gun and a 1.15 mm focal length magnetic lens to produce a probe on the specimen. The aperture size is chosen to allow one wavelength of spherical aberration at the edge of the objective aperture. Under these conditions the profile of the focused spot is expected to be similar to an Airy intensity distribution with the first zero at the same point but with a peak intensity 80 per cent of that which would be obtained If the lens had no aberration. This condition is attained when the half angle that the incident beam subtends at the specimen, 𝛂 = (4𝛌/Cs)¼

Symmetries and Extinction Rules in CBED

1982 ◽  
Vol 40 ◽  
pp. 684-685
Author(s):  
K. Ishizuka
Keyword(s):  
Electron Diffraction ◽  
Incident Beam ◽  
Convergent Beam Electron Diffraction ◽  
Beam Direction ◽  
Beam Electron ◽  
Convergent Beam

The technique of convergent-beam electron diffraction (CBED) has been established. However there is a distinct discrepancy concerning the CBED pattern symmetries associated with translation symmetries parallel to the incident beam direction: Buxton et al. assumed no detectable effects of translation components, while Goodman predicted no associated symmetries. In this report a procedure used by Gjønnes & Moodie1 to obtain dynamical extinction rules will be extended in order to derive the CBED pattern symmetries as well as the dynamical extinction rules.

Remarks on the application of backscattered electron imaging (BEI) to the scanning electron microscopy (SEM) of biological structures

1983 ◽  
Vol 41 ◽  
pp. 484-487
Author(s):  
Etienne de Harven
Keyword(s):  
High Resolution ◽  
Incident Beam ◽  
Spot Size ◽  
Primary Electron ◽  
Critical Point Drying ◽  
Cell Shapes ◽  
High Resolution Images ◽  
Backscattered Electron ◽  
Electron Imaging ◽  
Scanning Electron

Biological ultrastructures have been extensively studied with the scanning electron microscope (SEM) for the past 12 years mainly because this instrument offers accurate and reproducible high resolution images of cell shapes, provided the cells are dried in ways which will spare them the damage which would be caused by air drying. This can be achieved by several techniques among which the critical point drying technique of T. Anderson has been, by far, the most reproducibly successful. Many biologists, however, have been interpreting SEM micrographs in terms of an exclusive secondary electron imaging (SEI) process in which the resolution is primarily limited by the spot size of the primary incident beam. in fact, this is not the case since it appears that high resolution, even on uncoated samples, is probably compromised by the emission of secondary electrons of much more complex origin.When an incident primary electron beam interacts with the surface of most biological samples, a large percentage of the electrons penetrate below the surface of the exposed cells.

Optimizing conditions for x-ray microchemical analysis in analytical electron microscopy

1978 ◽  
Vol 36 (1) ◽  
pp. 548-549 ◽  
Author(s):  
N. J. Zaluzec
Keyword(s):  
Solid Angle ◽  
Analytical Electron Microscopy ◽  
Incident Beam ◽  
Thin Foil ◽  
Experimental Conditions ◽  
X Ray ◽  
Microchemical Analysis ◽  
Analytical Electron ◽  
Image Position ◽  
Incident Beam Energy

The ultimate sensitivity of microchemical analysis using x-ray emission rests in selecting those experimental conditions which will maximize the measured peak-to-background (P/B) ratio. This paper presents the results of calculations aimed at determining the influence of incident beam energy, detector/specimen geometry and specimen composition on the P/B ratio for ideally thin samples (i.e., the effects of scattering and absorption are considered negligible). As such it is assumed that the complications resulting from system peaks, bremsstrahlung fluorescence, electron tails and specimen contamination have been eliminated and that one needs only to consider the physics of the generation/emission process.The number of characteristic x-ray photons (Ip) emitted from a thin foil of thickness dt into the solid angle dΩ is given by the well-known equation

A General Method for Spectrometer Design in the Scoff Approximation

1976 ◽  
Vol 34 ◽  
pp. 538-539
Author(s):  
J. R. Fields
Keyword(s):  
Electron Microscope ◽  
Transmission Electron Microscope ◽  
Energy Analysis ◽  
Incident Beam ◽  
Scanning Transmission Electron Microscope ◽  
Chemical Identification ◽  
Scanning Transmission Electron ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
General Method

The energy analysis of electrons scattered by a specimen in a scanning transmission electron microscope can improve contrast as well as aid in chemical identification. In so far as energy analysis is useful, one would like to be able to design a spectrometer which is tailored to his particular needs. In our own case, we require a spectrometer which will accept a parallel incident beam and which will focus the electrons in both the median and perpendicular planes. In addition, since we intend to follow the spectrometer by a detector array rather than a single energy selecting slit, we need as great a dispersion as possible. Therefore, we would like to follow our spectrometer by a magnifying lens. Consequently, the line along which electrons of varying energy are dispersed must be normal to the direction of the central ray at the spectrometer exit.

Analysis of Contrast Reversal in SEM Images

1972 ◽  
Vol 30 ◽  
pp. 398-399
Author(s):  
M. D. Coutts ◽  
E. R. Levin
Keyword(s):  
Incident Beam ◽  
Normal Incidence ◽  
Beam Current ◽  
Secondary Emission ◽  
Image Contrast ◽  
Sem Images ◽  
Secondary Electrons ◽  
Image Position

On tilting samples in an SEM, the image contrast between two elements, x and y often decreases to zero at θε, which we call the no-contrast angle. At angles above θε the contrast is reversed, θ being the angle between the specimen normal and the incident beam. The available contrast between two elements, x and y, in the SEM can be defined as,(1)where ix and iy are the total number of reflected and secondary electrons, leaving x and y respectively. It can easily be shown that for the element x,(2)where ib is the beam current, isp the specimen absorbed current, δo the secondary emission at normal incidence, k is a constant, and m the reflected electron coefficient.

Sign in / Sign up

Export Citation Format

Share Document